User Manual

Secure Network Access
Your machine’s default password is on the label on the back
of the machine (preceded by "Pwd").
We strongly recommend you change it to protect your
machine from unauthorised access.
NOTE
• Most of the illustrations in this Quick Setup Guide show the MFC-J890DW.
• Save all packing materials and the box in case for any reason you must
ship your machine.
• You must purchase the correct interface cable for the interface you
want to use. A USB cable is included with some models.
USB cable
We recommend using a USB 2.0 cable (Type A/B) that is no more than
2 metres long.
Ethernet (Network) cable (MFC-J690DW/J890DW only)
Use a straight-through Category5 (or greater) twisted-pair cable for
10BASE-T or 100BASE-TX Fast Ethernet Network.
2
Load paper in the paper tray
1
Unpack the machine and check the components
The components included in the box may differ depending on your country.
Remove the protective tape and film covering the machine and the touchscreen.
Connect the telephone line cord.
Use the socket marked LINE.
Follow the touchscreen
instructions to unpack and install
the ink cartridges.
The machine will prepare the ink
tube system for printing.
When the machine has finished the initial cleaning
process, follow the touchscreen instructions to
configure the machine’s settings.
• Check print quality
• Set Brother LCD Message defaults
• Print the installation sheet
Open the ink cartridge cover, and then
remove the orange protective part
from the machine.
After turning the machine on, you may need to set your
country or language (depending on your machine).
If required, follow the touchscreen instructions.
Connect the power cord. The machine will power
on automatically.
NOTE
If you are sharing one telephone line with an external
telephone, connect it as shown below.
NOTE
You can adjust the control panel angle to read the
touchscreen more easily.
NOTE
Do not throw away the orange protective part.
You will need it if you transport the machine.
a. Extension telephone
b. External telephone
Quick Setup Guide
DCP-J772DW / MFC-J690DW / MFC-J890DW
Read the Product Safety Guide first, then read this Quick Setup Guide
for the correct installation procedure.
3
Connect the power cord
6
Install the inbox ink cartridges
4
Select your country
or language
(Initial setup only)
7
Machine settings
D01D64001-01
OCE/ASA
Version C
(Australia
only)
(Hong Kong
only)
Inbox Ink Cartridges*
• Black
• Yellow
• Cyan
• Magenta
*
Ink cartridges contain
approximately the same
page yield as replacement
cartridges (Standard).
Quick Setup Guide
Product Safety Guide
Power Cord Telephone Line Cord
Adapter
(MFC models only)
Brother Installation Disc Telephone Line Cord
(MFC models only)
1. Press [Settings] > [All Settings] >
[Initial Setup] > [Local Language].
2. Press your language.
3. Press .
8
Select your language
(if needed and only for
certain models)
9
Connect the telephone line cord (MFC models only)
If you are not using your machine as a fax, go to
10
.
The latest manuals are available at the Brother Solutions Center:
support.brother.com/manuals
Watch our FAQ videos for help
with setting up your Brother
machine.
support.brother.com/videos
5
Set the date and time
Follow the touchscreen instructions to set the date and
time.
Quickly shake just the black
ink cartridge horizontally
15 times as shown, before
inserting it into the machine.
Pull the paper tray completely
out of the machine.
Open the output paper tray
cover a. Fan the paper well and load it in the tray.
Close the output paper tray cover, and
then slowly push the tray completely
into the machine.
Adjust the paper guides.
NOTE
Pull out the paper support a, and unfold
thepapersupportapb so that the
printed pages do not fall.



(Example for Australia)
(Example for
Australia)
1
2
(Example for Australia)