Network User's Guide
Table Of Contents
- NETWORK USER’S GUIDE
- Definitions of notes
- IMPORTANT NOTE
- Table of Contents
- 1 Introduction
- 2 Changing your machine’s network settings
- 3 Configuring your machine for a wireless network (For MFC-9560CDW and MFC-9970CDW)
- Overview
- Step by step chart for wireless network configuration
- Confirm your network environment
- Confirm your wireless network setup method
- Configuration using WPS or AOSS™ from the control panel menu to configure your machine for a wireless network (Automatic Wireless mode) (Infrastructure mode only) (Recommended)
- Configuration using the machine’s control panel Setup Wizard to configure your machine for a wireless network
- Configuration using the Brother installer application on the CD-ROM to configure your machine for a wireless network
- Configuration using the PIN Method of Wi-Fi Protected Setup to configure your machine for a wireless network (Infrastructure mode only)
- Configuring your machine for a wireless network (For Infrastructure mode and Ad-hoc mode)
- Using WPS or AOSS™ from the control panel menu to configure your machine for a wireless network (Automatic Wireless mode)
- Using the Setup Wizard from the control panel
- Configuring your machine when the SSID is not broadcast
- Configuring your machine for an enterprise wireless network
- Using the Brother installer application on the CD-ROM to configure your machine for a wireless network
- Using the PIN Method of Wi-Fi Protected Setup
- 4 Wireless configuration using the Brother installer application (For MFC-9560CDW and MFC-9970CDW)
- 5 Control panel setup
- Network menu
- TCP/IP
- Ethernet (wired network only)
- Status (For DCP-9055CDN, DCP-9270CDN, MFC-9460CDN and MFC-9465CDN)/Wired Status (For MFC-9560CDW and MFC-9970CDW)
- Setup Wizard (wireless network only)
- WPS or AOSS™ (wireless network only)
- WPS w/PIN Code (wireless network only)
- WLAN Status (wireless network only)
- MAC Address
- Set to Default (For MFC-9560CDW and MFC-9970CDW)
- Wired Enable (For MFC-9560CDW and MFC-9970CDW)
- WLAN Enable (For MFC-9560CDW and MFC-9970CDW)
- E-mail / IFAX (MFC-9970CDW and DCP-9270CDN (E-mail only))
- Fax to Server (For MFC-9970CDW)
- How to set a new default for Scan to FTP
- How to set a new default for Scan to Network
- Reset the network settings to the factory default
- Printing the Network Configuration List
- Printing the WLAN report (For MFC-9560CDW and MFC-9970CDW)
- Function table and default factory settings
- Network menu
- 6 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Password information
- Secure Function Lock 2.0
- Synchronize with SNTP server
- Store Print Log to Network
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser
- Changing the LDAP configuration using a web browser (For DCP-9270CDN and MFC-9970CDW)
- 7 LDAP operation (For DCP-9270CDN and MFC-9970CDW)
- 8 Internet fax (For MFC-9970CDW)
- 9 Security features
- Overview
- Managing your network machine securely using SSL/TLS
- Printing documents securely using SSL/TLS
- Sending or Receiving an E-mail securely
- Using IEEE 802.1x authentication
- Secure Management using BRAdmin Professional 3 (Windows®)
- Using Certificates for device security
- Managing multiple certificates
- 10 Troubleshooting
- Appendix A
- Index
- Network Glossary
- Table of Contents
- 1 Types of network connections and protocols
- 2 Configuring your machine for a network
- 3 Wireless network terms and concepts
- 4 Additional network settings from Windows®
- 5 Security terms and concepts
- Appendix A
- Index
Security features
104
9
Using IEEE 802.1x authentication 9
You can configure IEEE 802.1x authentication for a wired or a wireless network.
To use IEEE 802.1x authentication, you must install a certificate issued by a CA. Contact your network
administrator or your ISP (Internet Service Provider) whether a CA certificate import is necessary. (For how
to install a certificate, see Using Certificates for device security on page 107.)
IEEE 802.1x authentication configuration using Web Based Management (web
browser) 9
If you are configuring IEEE 802.1x authentication for a wired or a wireless network using Web Based
Management, follow the instructions.
You can also configure IEEE 802.1x authentication using:
(Wired network)
BRAdmin Professional 3
(Wireless network)
Wireless setup wizard from the control panel (For details, see Configuring your machine for an enterprise
wireless network on page 23.)
Wireless setup wizard on the CD-ROM (For details, see Wireless configuration using the Brother installer
application (For MFC-9560CDW and MFC-9970CDW) on page 35.)
BRAdmin Professional 3
Note
• If you configure your machine using EAP-TLS Authentication, you must install the Client Certificate before
you start configuration. If you have installed more than one certificate, we recommend you write down the
certificate you want to use. For installing the certificate, see Using Certificates for device security
on page 107.
• Before you verify the Server Certificate, you must import the CA certificate that has been issued by the CA
that signed the Server Certificate. Contact your system administrator about the CA certificate. For
importing the certificate, see Import and export a CA certificate on page 117.
• For the details of each certificate, see Using Certificates for device security on page 107.
a Start your web browser.
b Type “http://machine’s IP address/” into your browser (where “machine’s IP address” is
the machine’s IP address).
For example:
http://192.168.1.2/