Network User's Guide
Table Of Contents
- NETWORK USER’S GUIDE
- Definitions of notes
- IMPORTANT NOTE
- Table of Contents
- 1 Introduction
- 2 Changing your machine’s network settings
- 3 Configuring your machine for a wireless network (For MFC-9560CDW and MFC-9970CDW)
- Overview
- Step by step chart for wireless network configuration
- Confirm your network environment
- Confirm your wireless network setup method
- Configuration using WPS or AOSS™ from the control panel menu to configure your machine for a wireless network (Automatic Wireless mode) (Infrastructure mode only) (Recommended)
- Configuration using the machine’s control panel Setup Wizard to configure your machine for a wireless network
- Configuration using the Brother installer application on the CD-ROM to configure your machine for a wireless network
- Configuration using the PIN Method of Wi-Fi Protected Setup to configure your machine for a wireless network (Infrastructure mode only)
- Configuring your machine for a wireless network (For Infrastructure mode and Ad-hoc mode)
- Using WPS or AOSS™ from the control panel menu to configure your machine for a wireless network (Automatic Wireless mode)
- Using the Setup Wizard from the control panel
- Configuring your machine when the SSID is not broadcast
- Configuring your machine for an enterprise wireless network
- Using the Brother installer application on the CD-ROM to configure your machine for a wireless network
- Using the PIN Method of Wi-Fi Protected Setup
- 4 Wireless configuration using the Brother installer application (For MFC-9560CDW and MFC-9970CDW)
- 5 Control panel setup
- Network menu
- TCP/IP
- Ethernet (wired network only)
- Status (For DCP-9055CDN, DCP-9270CDN, MFC-9460CDN and MFC-9465CDN)/Wired Status (For MFC-9560CDW and MFC-9970CDW)
- Setup Wizard (wireless network only)
- WPS or AOSS™ (wireless network only)
- WPS w/PIN Code (wireless network only)
- WLAN Status (wireless network only)
- MAC Address
- Set to Default (For MFC-9560CDW and MFC-9970CDW)
- Wired Enable (For MFC-9560CDW and MFC-9970CDW)
- WLAN Enable (For MFC-9560CDW and MFC-9970CDW)
- E-mail / IFAX (MFC-9970CDW and DCP-9270CDN (E-mail only))
- Fax to Server (For MFC-9970CDW)
- How to set a new default for Scan to FTP
- How to set a new default for Scan to Network
- Reset the network settings to the factory default
- Printing the Network Configuration List
- Printing the WLAN report (For MFC-9560CDW and MFC-9970CDW)
- Function table and default factory settings
- Network menu
- 6 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Password information
- Secure Function Lock 2.0
- Synchronize with SNTP server
- Store Print Log to Network
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser
- Changing the LDAP configuration using a web browser (For DCP-9270CDN and MFC-9970CDW)
- 7 LDAP operation (For DCP-9270CDN and MFC-9970CDW)
- 8 Internet fax (For MFC-9970CDW)
- 9 Security features
- Overview
- Managing your network machine securely using SSL/TLS
- Printing documents securely using SSL/TLS
- Sending or Receiving an E-mail securely
- Using IEEE 802.1x authentication
- Secure Management using BRAdmin Professional 3 (Windows®)
- Using Certificates for device security
- Managing multiple certificates
- 10 Troubleshooting
- Appendix A
- Index
- Network Glossary
- Table of Contents
- 1 Types of network connections and protocols
- 2 Configuring your machine for a network
- 3 Wireless network terms and concepts
- 4 Additional network settings from Windows®
- 5 Security terms and concepts
- Appendix A
- Index
Security features
103
9
You will also need to check SMTP-AUTH of SMTP Server Authentication Method to enable the SMTP
server authentication.
SMTP settings
You can change the SMTP port number using Web Based Management. This is useful if your ISP (Internet
Service Provider) implements the “Outbound Port 25 Blocking (OP25B)” service.
By changing the SMTP port number to a specific number which your ISP is using for the SMTP server (for
example, port 587), you would then be able to send an E-mail via the SMTP server.
If you can use both POP before SMTP and SMTP-AUTH, we recommend choosing SMTP-AUTH.
If you choose POP before SMTP for the SMTP Server Authentication Method, you need to configure the
POP3 settings. You can also use the APOP method if needed.
Sending or Receiving an E-mail securely using SSL/TLS 9
This machine supports SSL/TLS methods to send or receive an E-mail via an E-mail server that requires
secure SSL/TLS communication. To send or receive E-mail via an E-mail server that is using SSL/TLS
communication, you must configure SMTP over SSL/TLS or POP3 over SSL/TLS correctly.
Verifying Server Certificate
If you choose SSL or TLS for SMTP over SSL/TLS or POP3 over SSL/TLS, the Verify Server Certificate
check box will be automatically checked to verify the Server Certificate.
• Before you verify the Server Certificate, you must import the CA certificate that has been issued by the
CA that signed the Server Certificate. Contact your system administrator about the CA certificate. For
importing the certificate, see Import and export a CA certificate on page 117.
• If you do not need to verify the Server Certificate, uncheck Verify Server Certificate.
Port Number
If you choose SSL or TLS, the SMTP Port or POP3 Port value will be changed to match the protocol. If
you want to change the port number manually, enter the port number after you choose SMTP over
SSL/TLS or POP3 over SSL/TLS.
You must configure the POP3/SMTP communication method to match the E-mail server. For details of the
E-mail server settings, contact your network administrator or Internet services provider.
In most cases, the secured webmail services require the following settings:
(SMTP)
SMTP Port: 587
SMTP Server Authentication Method: SMTP-AUTH
SMTP over SSL/TLS: TLS
(POP3)
POP3 Port: 995
POP3 over SSL/TLS: SSL