Basic User's Guide
Table Of Contents
- BASIC USER’S GUIDE MFC-9460CDN/ MFC-9560CDW
- Brother numbers
- Ordering accessories and supplies
- Notice - Disclaimer of Warranties (USA and Canada)
- Compilation and Publication Notice
- Brother™ Color Laser One-Year On-Site Limited Warranty (USA only)
- BROTHER LASER PRINTER / MULTIFUNCTION CENTER® / FAXON-SITE LIMITED WARRANTY (Canada Only)
- User's Guides and where do I find it?
- Table of Contents
- 1 General information
- 2 Loading paper
- Loading paper and print media
- Paper settings
- Acceptable paper and other print media
- 3 Loading documents
- 4 Sending a fax
- 5 Receiving a fax
- 6 Telephone services and external devices
- 7 Dialing and storing numbers
- 8 Making copies
- 9 Printing data from a USB Flash memory drive or digital camera supporting mass storage
- 10 How to print from a computer
- 11 How to scan to a computer
- A Routine maintenance
- B Troubleshooting
- Error and maintenance messages
- Document Jams and Paper Jams
- Document is jammed in the top of the ADF unit
- Document is jammed under the document cover
- Removing small documents jammed in the ADF
- Document is jammed at the output tray
- Paper is jammed in the MP tray
- Paper is jammed in paper tray 1 or tray 2
- Paper is jammed at the back of the machine
- Paper is jammed inside the machine
- Paper is jammed underneath paper tray 1
- If you are having difficulty with your machine
- Improving the print quality
- Machine Information
- C Menu and features
- D Specifications
- Index
- brother USA/CAN
Troubleshooting
97
B
Condensation One of the issues that can cause
this error is that condensation
may form inside the machine after
a room temperature change.
Leave switched ON. Fully open the front
cover. Wait 30 minutes, switch OFF and
close cover, then switch ON. If this does not
clear the error, call Brother Customer
Service.
Connection Fail You tried to poll a fax machine
that is not in Polled Waiting mode.
Check the other fax machine’s polling setup.
Cooling Down
Wait for a while
The temperature of the drum unit
or toner cartridge is too hot. The
machine will pause its current
print job and go into cooling down
mode. During the cooling down
mode, you will hear the cooling
fan running while the LCD shows
Cooling Down, and Wait for
a while.
Make sure that you can hear the fan in the
machine spinning and that the exhaust
outlet is not blocked by something.
If the fan is spinning, remove any obstacles
that surround the exhaust outlet, and then
leave the machine turned on but do not use
it for several minutes.
If the fan is not spinning, disconnect the
machine from the power for several minutes,
then reconnect it.
Cover is Open The front cover is not completely
closed.
Close the front cover of the machine.
Cover is Open The ADF cover is not completely
closed.
Close the ADF cover of the machine.
The ADF is open while loading a
document.
Close the ADF cover of the machine, then
press Stop/Exit.
Cover is Open The fuser cover is not completely
closed or paper was jammed in
the back of the machine when
you turned on the power.
Close the fuser cover of the machine.
Make sure paper is not jammed inside
the back of the machine, and then close
the fuser cover and press Black Start or
Color Start.
DIMM Error The DIMM is not installed
correctly.
The DIMM is broken.
The DIMM does not meet the
required specifications.
Turn off the machine and remove the
DIMM.
Confirm the DIMM meets the required
specifications. (See Memory board in
Appendix B of the Advanced User's
Guide.)
Re-install the DIMM correctly. Wait a few
seconds, and then turn it on again.
If this error message appears again,
replace the DIMM with a new one. (See
Installing extra memory in Appendix B of
the Advanced User's Guide.)
Disconnected The other person or other
person’s fax machine stopped the
call.
Try to send or receive again.
Error Message Cause Action