User`s guide
Table Of Contents
- NETWORK USER’S GUIDE
- Table of Contents
- 1 Introduction
- 2 Configuring your machine for a network
- Overview
- IP addresses, subnet masks and gateways
- Step by step chart
- Setting the IP address and subnet mask
- Changing the print server settings
- Using the BRAdmin Light utility to change the print server settings
- Using the BRAdmin Professional 3 utility to change print server settings (Windows®)
- Using the control panel to change the print server settings
- Using Web Based Management (web browser) to change the print/scan server settings
- Using Remote Setup to change the print server settings (Not available for Windows Server® 2003/2008) (Not available for DCP-8085DN)
- Using other methods to change print server settings
- 3 Control panel setup
- 4 Driver Deployment Wizard (Windows® only)
- 5 Network printing from Windows®: basic TCP/IP Peer-to-Peer printing
- 6 Internet printing for Windows®
- 7 Network printing from Macintosh using the BR-Script 3 driver
- 8 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Password information
- Secure Function Lock 2.0 (Not available for MFC-8370DN)
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser
- Changing the LDAP configuration using a web browser (For MFC-8880DN)
- 9 LDAP operation (For MFC-8880DN)
- 10 Internet fax and Scan to E-mail (E-mail server) (For MFC-8880DN)
- Internet fax Overview
- Getting connected
- Control panel key functions
- Sending an Internet fax
- Manually entering text
- Receiving E-mail or Internet fax
- Receiving an Internet fax to your computer
- Forwarding received E-mail and fax messages
- Relay broadcasting
- TX Verification Mail
- Setup Mail TX
- Setup Mail RX
- Error mail
- Important information on Internet fax
- Scan to E-mail (E-mail server) overview
- Internet fax Overview
- 11 Security features
- 12 Troubleshooting
- Appendix A
- Using services
- Other ways to set the IP address (for advanced users and administrators)
- Using DHCP to configure the IP address
- Using BOOTP to configure the IP address
- Using RARP to configure the IP address
- Using APIPA to configure the IP address
- Using ARP to configure the IP address
- Using the TELNET console to configure the IP address
- Using the Brother Web BRAdmin server software for IIS to configure the IP address
- Installation when using web services (Windows Vista®)
- Installation when using a Network Print Queue or Share (printer driver only)
- Appendix B
- Appendix C
- Index
20
3
3
Network menu 3
Before using your Brother product in a network environment, you need to configure the correct TCP/IP
settings.
In this chapter, you will learn how to configure the network settings using the control panel, located on the
front of the machine.
The Network menu selections of the control panel allow you to set up the Brother machine for your network
configuration. Press Menu, then press a or b to choose Network. Proceed to the menu selection you wish
to configure. For additional information on the menu, see Function table and default factory settings
on page 131.
Please note that the machine is supplied with the BRAdmin Light utility and Remote Setup applications, which
also can be used to configure many aspects of the network. (See Changing the print server settings
on page 17.)
TCP/IP 3
This menu has ten sections: Boot Method, IP Address, Subnet Mask, Gateway, Node Name,
WINS Config, WINS Server, DNS Server, APIPA and IPv6.
Boot Method 3
This selection controls how the machine obtains an IP address. The default setting is Auto.
Note
If you do not want your print server configured via DHCP, BOOTP or RARP, you must set the
Boot Method to Static so that the print server has a static IP address. This will prevent the print server
from trying to obtain an IP address from any of these systems. To change the Boot Method, use the
machine’s control panel, BRAdmin Light utility, Remote Setup or Web Based Management (web browser).
a Press Menu.
b Press a or b to choose Network.
Press OK.
c Press a or b to choose TCP/IP.
Press OK.
d Press a or b to choose Boot Method.
Press OK.
e Press a or b to choose Auto
1
, Static
2
, RARP
3
, BOOTP
4
or DHCP
5
.
Press OK.
If you chose Auto, RARP, BOOTP or DHCP, go to step f.
If you chose Static, go to step g.
Control panel setup 3