User's Manual
Table Of Contents
- USER’S GUIDE FAX-2820/FAX-2910/FAX-2920/MFC-7220/MFC-7225N
- Brother numbers
- Ordering accessories and supplies
- Safety precautions
- Quick Reference Guide
- Table of Contents
- 1 Introduction
- 2 Getting started
- Initial setup
- General Setup
- Setting the Mode Timer (FAX-2820, FAX-2910 and FAX-2920 only)
- Setting the Mode Timer (MFC-7220 and MFC-7225N only)
- Setting the Paper Type
- Setting the Paper Size
- Setting the Ring Volume
- Setting the Beeper Volume
- Setting the Speaker Volume
- Setting the Handset Volume
- Choosing the Handset Volume (For Volume Amplify)
- Setting Volume Amplify
- Turning on Automatic Daylight Savings Time
- Toner Save
- Sleep Time
- Setting the LCD Contrast
- Security
- TX Lock (FAX-2820, FAX-2910 and MFC-7220 only)
- Memory Security (FAX-2920 and MFC-7225N only)
- Setting Lock
- 3 Setup Send
- 4 Setup Receive
- 5 Quick-Dial numbers and dialing options
- 6 Remote Fax Options
- 7 Printing reports
- 8 Making copies
- 9 Software and Network Features (MFC-7220 and MFC-7225N only)
- 10 Important information
- Standard telephone and FCC Notices These notices are in effect on models sold and used in the United States only.
- Federal Communications Commission (FCC) Declaration of Conformity (USA only)
- Industry Canada Compliance Statement (Canada only)
- Disconnect device
- LAN connection (MFC-7225N only)
- Laser safety
- FDA regulations
- Important safety instructions
- Trademarks
- 11 Troubleshooting and routine maintenance
- Appendix A
- Appendix B
- Glossary
- Specifications
- Product description
- General
- Print media
- Copy
- Fax
- Scanner (MFC-7220 and MFC-7225N only)
- Printer (not available for FAX-2910)
- Interfaces (not available for FAX-2910)
- Download the optional software from the Brother Web Site (FAX-2820 and FAX-2920 users only)
- At the same time, you can download the manual for setting up and using the PC-Fax software.
- Computer requirements (not available for FAX-2910)
- Consumable items
- Network (LAN) (MFC-7225N only)
- Index
- Remote Retrieval Access card
- brother USA/CAN
Chapter 11
11 - 5
Unable to Init.
(Initialize)
Unable to Print
Unable to Scan
The machine has a mechanical
problem.
(For FAX-2820, FAX-2910 and MFC-7220)
When you turn off the machine's power switch its
memory will be cleared. To check whether the
machine has faxes in its memory see Checking if the
machine has faxes in its memory on page 11-6. If there
are faxes you need to save them before following the
suggestions below (To save the faxes, see Forwarding
faxes to another fax machine on page 11-6. For
MFC-7220 also see Transferring faxes to your PC
(MFC-7220 and MFC-7225N only) on page 11-6).
Turn off the machine's power switch and then turn it on
again. If the error message continues, leave the
machine for several minutes and try it again.
(For FAX-2920 and MFC-7225N)
Turn off the machine's power switch and then turn it on
again. If the error message continues leave the
machine for several minutes and then try it again. (The
machine can be turned off for up to 4 days without
losing faxes stored in the memory.)
Wrong Paper Size Paper is not the correct size. Load the correct size of paper (Letter, Legal or A4) and
then press Start.
ERROR MESSAGES
ERROR MESSAGE CAUSE ACTION