User's Manual
Table Of Contents
- USER’S GUIDE FAX-2820/FAX-2910/FAX-2920/MFC-7220/MFC-7225N
- Brother numbers
- Ordering accessories and supplies
- Safety precautions
- Quick Reference Guide
- Table of Contents
- 1 Introduction
- 2 Getting started
- Initial setup
- General Setup
- Setting the Mode Timer (FAX-2820, FAX-2910 and FAX-2920 only)
- Setting the Mode Timer (MFC-7220 and MFC-7225N only)
- Setting the Paper Type
- Setting the Paper Size
- Setting the Ring Volume
- Setting the Beeper Volume
- Setting the Speaker Volume
- Setting the Handset Volume
- Choosing the Handset Volume (For Volume Amplify)
- Setting Volume Amplify
- Turning on Automatic Daylight Savings Time
- Toner Save
- Sleep Time
- Setting the LCD Contrast
- Security
- TX Lock (FAX-2820, FAX-2910 and MFC-7220 only)
- Memory Security (FAX-2920 and MFC-7225N only)
- Setting Lock
- 3 Setup Send
- 4 Setup Receive
- 5 Quick-Dial numbers and dialing options
- 6 Remote Fax Options
- 7 Printing reports
- 8 Making copies
- 9 Software and Network Features (MFC-7220 and MFC-7225N only)
- 10 Important information
- Standard telephone and FCC Notices These notices are in effect on models sold and used in the United States only.
- Federal Communications Commission (FCC) Declaration of Conformity (USA only)
- Industry Canada Compliance Statement (Canada only)
- Disconnect device
- LAN connection (MFC-7225N only)
- Laser safety
- FDA regulations
- Important safety instructions
- Trademarks
- 11 Troubleshooting and routine maintenance
- Appendix A
- Appendix B
- Glossary
- Specifications
- Product description
- General
- Print media
- Copy
- Fax
- Scanner (MFC-7220 and MFC-7225N only)
- Printer (not available for FAX-2910)
- Interfaces (not available for FAX-2910)
- Download the optional software from the Brother Web Site (FAX-2820 and FAX-2920 users only)
- At the same time, you can download the manual for setting up and using the PC-Fax software.
- Computer requirements (not available for FAX-2910)
- Consumable items
- Network (LAN) (MFC-7225N only)
- Index
- Remote Retrieval Access card
- brother USA/CAN
8 - 1
8
8
‘
Using the machine as a
copier
You can use your machine as a copier,
making up to 99 copies at a time.
Enter Copy mode
Before making copies, make sure that
(Copy) is illuminated in green. If it is
not, press (Copy) to enter Copy mode.
The default setting is Fax mode. You can
change the number of seconds or minutes
that the machine stays in Copy mode. (See
Setting the Mode Timer (FAX-2820,
FAX-2910 and FAX-2920 only) on page 2-3
or Setting the Mode Timer (MFC-7220 and
MFC-7225N only) on page 2-3.)
The printable area of your machine begins at
approximately 0.16 in. (4 mm) from both
sides and 0.12 in. (3 mm) from the top or
bottom of the paper.
Note
This printable area shown above is for a
single copy or a 1 in 1 copy using Letter or
Legal size paper. The printable area changes
with the paper size.
Making a single copy
1
Press (Copy) to illuminate it in
green.
2
Load your document.
(See Load document on page 1-7.)
3
Press Start.
Making copies
Copy Ratio
The LCD shows the default copy setting
Quality
No. of Copies
0.16" (4 mm)
0.12" (3 mm)
Unprintable
area