User`s guide
Table Of Contents
- TABLE OF CONTENTS
- Chapter 1 How to Configure TCP/IP printing for Unix Systems
- Chapter 2 How to Configure TCP/IP printing for Windows NT, LAN Server and OS/2 Warp Server
- Chapter 3 How to Configure Peer-to-Peer Printing for Windows 95/98
- Chapter 4 How to Configure Peer-to-Peer (NetBIOS) printing for Windows 95/98/NT, LAN Server and OS/2 Warp Server
- Chapter 5 How to Configure Brother Internet Print for Windows 95/98/NT
- Chapter 6 How to Configure Novell Netware printing using IPX/SPX
- General Information
- Creating a Print Queue Using BRAdmin32
- Configuring the Brother Print Server (Queue Server Mode in Bindery emulation mode) using BRAdmin32
- Configuring the Brother Print Server (Queue Server Mode in NDS mode) using BRAdmin32
- Configuring the Brother Print Server (Queue Server Mode in NDS mode) using Novell NWADMIN and BRAdmin32
- Configuring the Brother Print Server (Remote Server Mode in NDS mode) using Novell NWAdmin and BRAdmin32
- Configuring the Brother Print Server (Queue Server Mode in Bindery emulation mode) using PCONSOLE and BRCONFIG
- Configuring the Brother Print Server (Queue Server Mode in NDS mode) using PCONSOLE and BRCONFIG
- Configuring the Brother Print Server (Remote Printer Mode using PCONSOLE and BRCONFIG
- Testing the Print Queue
- Configuring the Workstation (DOS-based NetWare drivers)
- Configuring the Workstation (Windows 3.1x)
- Configuring the Workstation (Windows 95/98)
- Chapter 7 How to Configure Macintosh printing using Appletalk
- Chapter 8 How to Configure DLC/LLC printing for Windows NT
- Chapter 9 How to use the Web based management function
- Chapter 10 TROUBLESHOOTING
- Overview
- Installation problems
- Intermittent Problems
- TCP/IP Troubleshooting
- UNIX Troubleshooting
- Windows NT/LAN Server (TCP/IP) Troubleshooting
- Windows 95/98 Peer to Peer Print (LPR) Troubleshooting
- Windows 95/98 (or later) Peer-to-Peer (HP JetAdmin compatible method) Troubleshooting
- Windows 95/98/NT 4.0 Peer-to-Peer Print (NetBIOS) Troubleshooting
- Internet Print (TCP/IP) Troubleshooting
- Novell NetWare Troubleshooting
- AppleTalk Troubleshooting
- DLC/LLC Troubleshooting
- Web Browser Troubleshooting (TCP/IP)
- APPENDIX
- INDEX
7-1
Chapter 7
How to Configure Macintosh printing using
Appletalk
Brother Print Server’s support the AppleTalk protocol running over Ethernet (also known as
EtherTalk). This allows Macintosh users to print at the same time as all other Ethernet
network users.
AppleTalk
Our AppleTalk capabilities allow a Brother Printer to appear as a shareable printer node on an
AppleTalk Phase 2 network. The print servers broadcast information to Macintoshes on the
network and automatically appear in the Chooser program of each Macintosh. Brother Print
Servers support ASCII and Binary printing.
Macintosh Configuration
Your Brother Print Server is compatible with Apple Laserwriter 8 drivers (earlier versions of
the LaserWriter drivers may crash or cause PostScript errors on large networks). If you do not
have these drivers you must install them. Consult your Macintosh documentation for
instructions on how to do this.
Before you try to use the Brother Print Server, you must firstly enable the EtherTalk protocol
from the Network Control Panel on the Macintosh. If the EtherTalk protocol is not selectable,
or the Network Control Panel does not exist, you must use Apple's Network Installer software
to add these capabilities.