User`s guide
Table Of Contents
- TABLE OF CONTENTS
- Chapter 1 How to Configure TCP/IP printing for Unix Systems
- Chapter 2 How to Configure TCP/IP printing for Windows NT, LAN Server and OS/2 Warp Server
- Chapter 3 How to Configure Peer-to-Peer Printing for Windows 95/98
- Chapter 4 How to Configure Peer-to-Peer (NetBIOS) printing for Windows 95/98/NT, LAN Server and OS/2 Warp Server
- Chapter 5 How to Configure Brother Internet Print for Windows 95/98/NT
- Chapter 6 How to Configure Novell Netware printing using IPX/SPX
- General Information
- Creating a Print Queue Using BRAdmin32
- Configuring the Brother Print Server (Queue Server Mode in Bindery emulation mode) using BRAdmin32
- Configuring the Brother Print Server (Queue Server Mode in NDS mode) using BRAdmin32
- Configuring the Brother Print Server (Queue Server Mode in NDS mode) using Novell NWADMIN and BRAdmin32
- Configuring the Brother Print Server (Remote Server Mode in NDS mode) using Novell NWAdmin and BRAdmin32
- Configuring the Brother Print Server (Queue Server Mode in Bindery emulation mode) using PCONSOLE and BRCONFIG
- Configuring the Brother Print Server (Queue Server Mode in NDS mode) using PCONSOLE and BRCONFIG
- Configuring the Brother Print Server (Remote Printer Mode using PCONSOLE and BRCONFIG
- Testing the Print Queue
- Configuring the Workstation (DOS-based NetWare drivers)
- Configuring the Workstation (Windows 3.1x)
- Configuring the Workstation (Windows 95/98)
- Chapter 7 How to Configure Macintosh printing using Appletalk
- Chapter 8 How to Configure DLC/LLC printing for Windows NT
- Chapter 9 How to use the Web based management function
- Chapter 10 TROUBLESHOOTING
- Overview
- Installation problems
- Intermittent Problems
- TCP/IP Troubleshooting
- UNIX Troubleshooting
- Windows NT/LAN Server (TCP/IP) Troubleshooting
- Windows 95/98 Peer to Peer Print (LPR) Troubleshooting
- Windows 95/98 (or later) Peer-to-Peer (HP JetAdmin compatible method) Troubleshooting
- Windows 95/98/NT 4.0 Peer-to-Peer Print (NetBIOS) Troubleshooting
- Internet Print (TCP/IP) Troubleshooting
- Novell NetWare Troubleshooting
- AppleTalk Troubleshooting
- DLC/LLC Troubleshooting
- Web Browser Troubleshooting (TCP/IP)
- APPENDIX
- INDEX
2
-
3
Configuring an IP address for the Print Server
You must now set an IP address into the Brother Print Server. There are several ways of doing
this:
If your printer has an LCD panel you can use the front panel buttons to change the IP address,
subnet mask and gateway addresses. Refer to Quick Setup Guide for instructions on how to do
this. You can also use the BRadmin32 Windows utility to change the IP address. The print
server also understand automatic IP address allocation methods such as DHCP, BOOTP and
RARP.
Changing the IP Address using the BRAdmin32 application
Start the BRAdmin32 utility (from Windows 95/98 or NT4.0)
The BRAdmin32 utility can use the IPX/SPX or TCP/IP protocols to communicate with the
Brother Print Server. As the default IP address of Brother print servers is 192.0.0.192, the print
server will probably be incompatible with the IP address numbering scheme on your network.
If you are not using DHCP, BOOTP or RARP, you will probably want to change the IP
address. There are two ways that you can do this from within BRAdmin32. 1) Use the
IPX/SPX protocol, 2) use the TCP/IP protocol and let BRAdmin32 find the Brother Print
Server as an un-configured device.