Quick Setup Guide Start Here (EU only) HL-5380DN Before you can use the printer, read this Quick Setup Guide for the correct setup and installation. To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/. IMPORTANT DO NOT connect the interface cable yet.
Note Keep a minimum gap around the printer as shown in the illustration. 100mm(4 in.) 100mm (4 in.) 100mm (4 in.) 130mm (5.12 in.) Symbols used in this guide WARNING WARNINGS tell you what to do to prevent possible personal injury. CAUTION CAUTIONS specify procedures you must follow or avoid to prevent possible minor injuries. IMPORTANT specify procedures you must follow or avoid to prevent possible damage to the printer or other objects.
2 Install the drum unit and toner cartridge assembly e Put the drum unit and toner cartridge assembly into the printer until it clicks into place. IMPORTANT DO NOT connect the interface cable yet. f a b Close the front cover of the printer. Remove the packing tape from the outside of the printer. Press the front cover release button and open the front cover a. 11 c d Unpack the drum unit and toner cartridge assembly.
a 3 Load paper in the paper tray c Pull the paper tray completely out of the printer. d b Fan the stack of paper well to avoid paper jams and misfeeds. Put paper in the tray, and make sure that the paper is below the maximum paper mark a. The side to be printed on must be face down. 11 While pressing the blue paper-guide release lever a, slide the paper guides to fit the paper size you are loading in the tray. Make sure that the guides are firmly in the slots.
4 Print a test page e Press Go. The printer prints a test page. Check that the test page has printed correctly. IMPORTANT DO NOT connect the interface cable yet. a Make sure that the printer power switch is off. Connect the AC power cord to the printer. Note This function will not be available after the first print job you send from your computer. 5 b Turn on the printer power switch. c Unfold support flap1. a d After the printer has finished warming up, the LCD shows READY.
Macintosh Windows®, go to page 8 Macintosh, go to page 11 USB For USB interface cable Windows® 6 Choose your connection type For Parallel interface cable Windows® Macintosh 7 Windows® Windows®, go to page 15 Macintosh, go to page 20 Wired Network For Wired Network Parallel Windows®, go to page 13
USB Windows® For USB Interface Cable Users 7 Install the printer driver and connect the printer to your computer d Put the supplied CD-ROM into your CD-ROM drive. The opening screen will appear automatically. Choose your printer model and the language. IMPORTANT DO NOT connect the USB interface cable yet. Note Note If the Found New Hardware Wizard appears on your computer, click Cancel.
USB f Click USB cable users. Windows® i • For Windows Vista®, when the User Account Control screen appears, click Continue. • If you want to install the PS driver (Brother’s BR-Script Driver), choose Custom setup and then follow the on-screen instructions. When the Select Components screen appears, check PS (PostScript Emulation) Driver, and then continue following the on-screen instructions. g h When the License Agreement window appears, click Yes if you agree to the License Agreement.
USB j Click Finish. Note • If you want to register your product on-line, check On-Line Registration. • If you do not want to set your printer as Default printer, uncheck Set as Default Printer. • If you want to disable the Status Monitor, uncheck Enable Status Monitor. Finish The installation is now complete.
USB Macintosh For USB Interface Cable Users Remove the label covering the USB interface connector. Click Install Printer Driver on the menu screen. Connect the USB cable to the USB connector marked with a symbol, and then connect the cable to your Macintosh. g Click USB cable users and follow the on-screen instructions. Then, restart your Macintosh. IMPORTANT DO NOT connect the printer to a USB port on a keyboard or a non-powered USB hub. c d Make sure the printer power switch is on.
USB i j Choose the printer you wish to connect, and then click OK. When this screen appears, click OK. Finish 12 The installation is now complete.
Parallel Windows® For Parallel Interface Cable Users 7 Install the driver and connect the printer to your computer d Put the supplied CD-ROM into your CD-ROM drive. The opening screen will appear automatically. Choose your printer model and the language. IMPORTANT DO NOT connect the parallel interface cable yet. Note Note If the Found New Hardware Wizard appears on your computer, click Cancel.
Parallel f Click Parallel cable users. Windows® h Click Finish. Note • If you want to register your product on-line, check On-Line Registration. • If you do not want to set your printer as Default printer, uncheck Set as Default Printer. • If you want to disable the Status Monitor, uncheck Enable Status Monitor. Note • For Windows Vista®, when the User Account Control screen appears, click Continue.
Wired Network Windows® For Wired Network Interface Cable Users 7 For Peer-to-Peer network printer users d Put the supplied CD-ROM into your CD-ROM drive. The opening screen will appear automatically. Choose your printer model and the language. 2 TCP/IP 1 TCP/IP a Router b Network printer Note If you are using Windows® Firewall or a firewall function of anti-spyware or antivirus applications, temporarily disable them.
Wired Network f Click Network cable users. Windows® i Choose Search the network for devices and choose from a list of discovered devices (Recommended). Or enter your printer's IP Address or its node name. Click Next. Note • For Windows Vista®, when the User Account Control screen appears, click Continue. Note You can find your printer’s IP Address and the node name by printing out the Printer Settings Page. See Print the Printer Settings Page on page 24.
Wired Network k Windows® Click Finish. Note • If you want to register your product on-line, check On-Line Registration. • If you do not want to set your printer as Default printer, uncheck Set as Default Printer. • If you want to disable the Status Monitor, uncheck Enable Status Monitor. • If you disabled your Personal Firewall software (e.g. Windows® Firewall), turn it back on. Finish The installation is now complete.
Wired Network 7 For shared network printer users Windows® c Click Install Printer Driver on the menu screen. Note Choose the Install Printer Driver icon for your region. 11 3 TCP/IP 21 4 11 a b c d Client computer Also known as “Server” or “Print server” TCP/IP or USB or Parallel Printer d Click Network cable users.
Wired Network f Choose Network Shared Printer, and then click Next. Windows® Note XML Paper Specification Printer Driver The XML Paper Specification Printer Driver is the most suitable driver when printing from the applications that use the XML Paper Specification documents. Please download the latest driver by accessing the Brother Solutions Center at http://solutions.brother.com/. g Choose your printer's queue, and then click OK.
Wired Network Macintosh For Wired Network Interface Cable Users 7 a Connect the printer to your Macintosh and install the driver e Connect the network interface cable to the LAN connector marked with a symbol and then connect it to a free port on your hub. f b c Click Install Printer Driver on the menu screen. Click Network cable users and follow the on-screen instructions. Then, restart your Macintosh. Make sure the printer power switch is on. Turn on your Macintosh.
Wired Network h Macintosh Choose the printer you wish to connect, and then click OK. Note • If there is more than one of the same printer model connected on your network, the MAC Address (Ethernet Address) will be displayed after the model name. You can also confirm your IP Address by scrolling to the right. • You can find your printer’s MAC Address (Ethernet Address) and the IP Address by printing out the Printer Settings Page. See Print the Printer Settings Page on page 24.
For Network Users BRAdmin Light utility (For Windows® users) The BRAdmin Light is a utility for initial setup of Brother network connected devices. It can also search for Brother products in a TCP/IP environment, view the status and configure basic network settings, such as IP Address. For more information on BRAdmin Light, visit us at http://solutions.brother.com/.
For Network Users BRAdmin Light utility (For Mac OS X users) The BRAdmin Light is a utility for initial setup of Brother network connected devices. It can also search for Brother products on your network, view the status and configure basic network settings, such as IP Address from a computer running Mac OS X 10.3.9 or greater. The BRAdmin Light software will be installed automatically when you install the printer driver. If you have already installed the printer driver, you don’t have to install it again.
For Network Users Web Based Management (web browser) Reset the network settings to the factory default The Brother print server is equipped with a web server that allows you to monitor its status or change some of its configuration settings, using HTTP (Hyper Text Transfer Protocol). To reset all network settings of the print server to its factory default, follow the steps below. a Note • The login name for the Administrator is “admin” (case sensitive) and the default password is “access”.
Other Information Safety precautions To use the printer safely If you DO NOT follow these safety instructions, there is a possibility of a fire, electrical shock, burn or suffocation. Please keep these instructions for later reference and read them before attempting any maintenance. WARNING There are high voltage electrodes inside the printer. Before you clean the inside of the printer, make sure that you have turned off the power switch and unplugged the printer from the AC power outlet.
Other Information CAUTION Lightning and power surges can damage this product! We recommend that you use a quality surge protection device on the AC power outlet, or unplug the cords during a lightning storm. After you have just used the printer, some internal parts of the printer will be extremely hot. When you open the front or back cover (back output tray) of the printer, DO NOT touch the shaded parts shown in the illustration.
Other Information Regulations Federal Communications Commission (FCC) Declaration of Conformity (For USA only) Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA Telephone: (908) 704-1700 declares, that the products Product name: Laser Printer HL-5380DN Model number: HL-53 comply with Part 15 of the FCC Rules.
Other Information International ENERGY STAR® Compliance Statement The purpose of the International ENERGY STAR® Program is to promote the development and popularization of energy-efficient office equipment. As an ENERGY STAR® Partner, Brother Industries, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. IEC 60825-1+A2:2001 Specification This machine is a Class 1 laser product as defined in IEC 60825-1+A2: 2001 specifications.
Other Information EU Directive 2002/96/EC and EN50419 Warning - This printer must be earthed. The wires in the mains lead are coloured in line with the following code: Green and Yellow: Earth Blue: Neutral Brown: Live This equipment is marked with the above recycling symbol. It means that at the end of the life of the equipment you must dispose of it separately at an appropriate collection point and not place it in the normal domestic unsorted waste stream. This will benefit the environment for all.
Other Information Shipment of the printer If for any reason you must ship your printer, carefully package the printer to avoid any damage during transit. We recommend that you save and use the original packaging. The printer should also be adequately insured with the carrier. CAUTION When shipping the printer, the DRUM UNIT and TONER CARTRIDGE assembly must be removed from the printer and put in a plastic bag.
Other Information Supplied CD-ROM You can find a variety of information on the CD-ROM. Windows® Macintosh Install Printer Driver Install the printer driver. Install Other Drivers or Utilities Install optional drivers, utilities and Network management tools. Documentation View the Printer User’s Guide and Network User's Guide in HTML format. You can also view the manuals in PDF format by accessing the Brother Solutions Center.
Other Information Control panel 5 1 4 2 3 a Menu buttons + Move forward through menus. Move backward through menus. Set Choose the control panel menu. Select the chosen menus and settings. Back Go back one level in the menu structure. b Go button Exit from the control panel menu and reprint setting. Clear error messages. Pause and Continue printing. c Job Cancel button Stop and cancel the print operation in progress.
Options and Consumables Options The printer has the following optional accessories. You can expand the capabilities of the printer by adding these items. For more details about the optional Lower Tray Unit and compatible SO-DIMM Memory, visit us at http://solutions.brother.com/. For installing these items, see Chapter 5 of the User's Guide on the CD-ROM. Lower Tray Unit SO-DIMM Memory LT-5300 Second lower paper tray unit can hold up to 250 sheets of paper.
Trademarks Brother and the Brother logo are registered trademarks and BRAdmin Light and BRAdmin Professional are trademarks of Brother Industries, Ltd. Microsoft, Windows, Windows Server and Internet Explorer are registered trademarks of Microsoft Corporation in the United States and/or other countries. Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. Apple, Macintosh and Safari are trademarks of Apple Inc.
