User Manual
Table Of Contents
- USER’S GUIDE HL-3045CN HL-3075CW
- Symbols and conventions used in the documentation
- Table of Contents
- 1 Printing Methods
- 2 Driver and Software
- Printer driver
- Features in the printer driver (for Windows®)
- Basic tab
- Paper Size
- Orientation
- Copies
- Media Type
- Print Quality
- Colour/Mono
- Settings Dialog
- Multiple Page
- Manual Duplex / Booklet
- Paper Source
- Advanced tab
- Scaling
- Reverse Print
- Use Watermark
- Header-Footer Print
- Toner Save Mode
- Secure Print
- Administrator
- User Authentication (HL-3075CW only)
- Other Print Options
- Colour Calibration
- Use Reprint
- Sleep Time
- Improve Print Output
- Tray Settings tab
- Support
- Using the custom monochrome printer driver (for Windows®)
- Using the BR-Script3 printer driver (PostScript® 3™ language emulation for Windows®) (HL-3075CW only)
- Features in the printer driver (for Macintosh)
- Features in the printer driver (for Windows®)
- Using the BR-Script3 printer driver (Post Script® 3™ language emulation for Macintosh) (HL-3075CW only)
- Uninstalling the printer driver
- Software
- Printer driver
- 3 Control Panel
- 4 Option
- 5 Routine Maintenance
- 6 Troubleshooting
- Appendix A
- Printer specifications
- Symbol and character sets (HL-3075CW only)
- Quick reference for bar code control commands (HL-3075CW only)
- Print bar codes or expanded characters
- Definition of parameters
- Bar code mode
- Bar code, expanded character, line block drawing and box drawing
- Bar code
- Bar code human readable line ON or OFF
- Quiet zone
- Bar code, expanded character unit, line block drawing and box drawing
- Bar code, expanded character, line block drawing and box drawing offset in X-axis
- Bar code & expanded character offset in Y-axis
- Bar code, expanded character, line block drawing and box drawing height
- Expanded character width, line block drawing and box drawing
- Expanded character rotation
- Bar code data start
- Box drawing
- Line block drawing
- Expanded character data start
- Print bar codes or expanded characters
- Libtiff Copyright and License
- Appendix B (for Europe and Other Countries)
- Appendix C (for USA and Canada)
- Index
Troubleshooting
143
6
No Toner Re-install the toner cartridge that is indicated on the LCD. (See Toner cartridges
on page 103)
Re-install the drum unit that is indicated on the LCD. (See Drum units on page 111)
No Waste Toner Re-install the Waste Toner Box. (See Waste toner box on page 121.)
Out of Memory If the LCD shows this error message when you print the secure data, Press Cancel and
delete the previously stored data.
Except in the case of printing secure data, add more memory. (See Installing extra memory
on page 99.)
Print Unable 1A Turn the power switch off and fully open the top cover. Leave the printer off and open for 30
minutes to remove any condensation from inside the machine, then close the top cover and
turn it on again. If this does not clear the error, call your dealer or a Brother Customer
Service.
Short Paper Open the back cover (back output tray) to let the printed paper out on the back out put tray.
Remove the printed pages and then press Go.
Size Mismatch Put the same size paper in the paper tray that is selected in the printer driver, and then press
Go, or select the size of paper you set in the Tray1 Size setting from the control panel.
Small Paper Open the back cover (back output tray) to let the printed paper out on the back out put tray
and then press Go.
Toner Error Pull out all the drum unit and toner cartridge assemblies. Take out the toner cartridge and
put it back into the printer again.
Unusable Device
(HL-3075CW only)
Remove the USB flash memory drive from the USB Direct Interface.
Error messages in Colour Correction
Call service message Action
Calibrate
<Scrolling message>
Calibration failed.
See Troubleshooting
chapter in User's
guide.
Turn off the printer. Wait a few seconds, then turn it on again.
Identify the colour causing the problem and put in a new drum unit. (See Replacing
the drum units on page 112.)
To identify the colour of the drum unit, visit us at http://solutions.brother.com/
to view
our FAQs and troubleshooting tips.
Put in a new belt unit. (See Replacing the belt unit on page 117.)
Put in a waste toner box. (See Replacing the waste toner box on page 122.)
If the problem continues, call your dealer or Brother Customer Service.
Registration
<Scrolling message>
Registration
failed. See
Troubleshooting
chapter in User's
guide.
Turn off the printer. Wait a few seconds, then turn it on again.
Put in a new belt unit. (See Replacing the belt unit on page 117.)
If the problem continues, call your dealer or Brother Customer Service.
Error messages (continued)
Error message Action