User Manual
Table Of Contents
- USER’S GUIDE HL-3045CN HL-3075CW
- Symbols and conventions used in the documentation
- Table of Contents
- 1 Printing Methods
- 2 Driver and Software
- Printer driver
- Features in the printer driver (for Windows®)
- Basic tab
- Paper Size
- Orientation
- Copies
- Media Type
- Print Quality
- Colour/Mono
- Settings Dialog
- Multiple Page
- Manual Duplex / Booklet
- Paper Source
- Advanced tab
- Scaling
- Reverse Print
- Use Watermark
- Header-Footer Print
- Toner Save Mode
- Secure Print
- Administrator
- User Authentication (HL-3075CW only)
- Other Print Options
- Colour Calibration
- Use Reprint
- Sleep Time
- Improve Print Output
- Tray Settings tab
- Support
- Using the custom monochrome printer driver (for Windows®)
- Using the BR-Script3 printer driver (PostScript® 3™ language emulation for Windows®) (HL-3075CW only)
- Features in the printer driver (for Macintosh)
- Features in the printer driver (for Windows®)
- Using the BR-Script3 printer driver (Post Script® 3™ language emulation for Macintosh) (HL-3075CW only)
- Uninstalling the printer driver
- Software
- Printer driver
- 3 Control Panel
- 4 Option
- 5 Routine Maintenance
- 6 Troubleshooting
- Appendix A
- Printer specifications
- Symbol and character sets (HL-3075CW only)
- Quick reference for bar code control commands (HL-3075CW only)
- Print bar codes or expanded characters
- Definition of parameters
- Bar code mode
- Bar code, expanded character, line block drawing and box drawing
- Bar code
- Bar code human readable line ON or OFF
- Quiet zone
- Bar code, expanded character unit, line block drawing and box drawing
- Bar code, expanded character, line block drawing and box drawing offset in X-axis
- Bar code & expanded character offset in Y-axis
- Bar code, expanded character, line block drawing and box drawing height
- Expanded character width, line block drawing and box drawing
- Expanded character rotation
- Bar code data start
- Box drawing
- Line block drawing
- Expanded character data start
- Print bar codes or expanded characters
- Libtiff Copyright and License
- Appendix B (for Europe and Other Countries)
- Appendix C (for USA and Canada)
- Index
Troubleshooting
142
6
LCD messages 6
If any problems occur, the printer automatically stops printing, diagnoses the problem, and displays the
resulting message on the LCD to alert you. Take the appropriate action, referring to the following tables. If
you cannot clear the problem, call the dealer you bought the printer from or Brother Customer Service.
Note
The LCD names for the paper trays are as follows.
• Standard paper tray: Tray 1
• Manual feed slot: Manual Feed
Error messages
Error message Action
Access Error
(HL-3075CW only)
The USB device was removed while data was processing. Press Cancel. Reinsert the USB
device and try to print with Direct Print or PictBridge.
Cartridge Error Take out the drum unit and toner cartridge assembly for the toner colour that is indicated on
the LCD. Remove the toner cartridge and then re-install it in the drum. Put the drum unit and
toner cartridge assembly back into the printer again. Repeat this process for each drum unit
and toner cartridge assembly until the error message is cleared from the LCD. If the problem
continues, call your dealer or Brother Customer Service.
Cover is Open Close the cover that is indicated on the LCD.
DIMM Error Turn off the printer. Re-install the DIMM correctly. Wait a few seconds, and then turn it on
again. If this error message appears again, replace the DIMM with a new one. (See
Installing extra memory on page 99.)
Drum Error
<Scrolling message>
Slide the Green
tab on Drum Unit.
Clean the corona wires. (See Cleaning the corona wires on page 130.)
Drum Error
<Scrolling message>
Replace the Drum
Unit.
Replace the drum unit with a new one for the colour that is indicated on the LCD. (See
Replacing the drum units on page 112.)
Fuser Error Turn the power switch off, wait a few seconds and then turn it again. Leave the printer for
15 minutes with the power on.
Jam XXX Carefully pull out the jammed paper from the area shown in Paper jams and how to clear
them on page 146.
Low Temperature Increase room temperature to allow the printer to operate.
Manual Feed Put the same size of paper in the manual feed slot as is shown on the LCD.
No Belt Unit Re-install the belt unit. (See Belt unit on page 117.)
No Paper Put the paper in the paper tray and then press Go, or put the paper in the manual feed slot.
If the problem is not solved, the paper pick-up roller may be stained. Clean the paper pick-
up roller. (See Cleaning the paper pick-up roller on page 139.)