Printer User Manual
Table Of Contents
- USER’S GUIDE HL-2130 HL-2132 HL-2135W HL-2220 HL-2230 HL-2240 HL-2240D HL-2242D HL-2250DN HL-2270DW
- Using this guide
- Table of Contents
- 1 Printing Methods
- 2 Driver and Software
- Printer driver
- Features in the printer driver (for Windows®)
- Basic tab
- Paper Size
- Orientation
- Copies
- Media Type
- Resolution
- Print Settings
- Multiple Page
- Duplex / Booklet
- Paper Source
- Advanced tab
- Scaling
- Reverse Print
- Use Watermark
- Header-Footer Print
- Toner Save Mode
- Administrator
- Other Print Options...
- Use Reprint
- Sleep Time
- Macro (HL-2250DN / HL-2270DW only)
- Density Adjustment
- Error Message Printout
- Improve Print Output
- Skip Blank Page
- Print Profiles tab
- Support
- Tray Settings
- Status Monitor
- Features in the printer driver (for Macintosh)
- Features in the printer driver (for Windows®)
- Uninstalling the printer driver
- Software
- Printer driver
- 3 Control Panel
- 4 Routine Maintenance
- 5 Troubleshooting
- A Appendix
- Machine specifications
- Symbol and character sets (HL-2250DN / HL-2270DW only)
- Quick reference for bar code control commands (HL-2250DN / HL-2270DW only)
- Print bar codes or expanded characters
- Definition of parameters
- Bar code mode
- Bar code, expanded character, line block drawing and box drawing
- Bar code
- Bar code human readable line ON or OFF
- Quiet zone
- Bar code, expanded character unit, line block drawing and box drawing
- Bar code, expanded character, line block drawing and box drawing offset in X-axis
- Bar code & expanded character offset in Y-axis
- Bar code, expanded character, line block drawing and box drawing height
- Expanded character width, line block drawing and box drawing
- Expanded character rotation
- Bar code data start
- Box drawing
- Line block drawing
- Expanded character data start
- Table of Code (EAN) 128 set C
- Print bar codes or expanded characters
- B Appendix (for Europe and Other Countries)
- C Appendix (for USA and Canada)
- Index
Troubleshooting
102
5
1
This message is for HL-2240D / HL-2242D / HL-2250DN / HL-2270DW only.
NO PAPER T1 The paper tray may be out of paper or not properly installed. If it is empty, put a
new stack of paper in the paper tray and then press Go. If the problem is still
unsolved, the paper pick-up roller may be dirty. Clean the paper pick-up roller. See
Cleaning the paper pick-up roller on page 94.
If there is paper in the paper tray, make sure it is straight. If the paper is curled,
straighten it before printing. Sometimes it is helpful to remove the paper, turn the
stack over and put it back in the paper tray.
Reduce the amount of paper in the paper tray, and then try again.
Make sure you use paper that meets Brother’s recommended paper
specifications. See Acceptable paper and other print media on page 3.
Load the same size paper that you selected in the current driver setting.
NO TONER Open the front cover, then install the toner cartridge.
PRINT OVERRUN Press Go to print the remaining data in the machine memory. Cancel the print job
if you want to delete the remaining data in the machine memory. See Go button
on page 60.
If this does not clear the error, reduce the complexity of your document or lower
the print resolution.
(HL-2250DN / HL-2270DW only)
Change the following settings in the supplied Windows
®
driver and try again. The
best combination of these settings will vary depending on your document:
•Graphics
1
• TrueType mode
1
• Use Printer TrueType
®
Fonts
1
1
Choose the Basic tab, choose Manual in Print Settings, and then click the Manual Settings....
REPLACE DRUM Replace the drum unit with a new one. See Replacing the drum unit on page 79
REPLACE TONER See Replacing the toner cartridge on page 71.
Service call error Check the LED indication to identify the error. See Service call indications
on page 58.
SIZE ERROR DX
1
Choose a paper size which is supported by the duplex tray. (See Type and size of
paper on page 4.)
TONER ENDED Replace the toner cartridge with a new one. See Replacing the toner cartridge
on page 71
TONER LOW Buy a new toner cartridge and have it ready for when the REPLACE TONER
status is indicated.
Error message Action