Setting Up Your Printer Step 1 Setting Up Your Printer Windows® USB Step 2 Windows® Parallel Installing the Driver Parallel page 12 page 14 USB Mac® OS 8.6 – 9.2 page 16 Mac® OS X 10.1 – 10.2 page 17 Macintosh® USB USB Installing the Driver Quick Setup Guide HL-1430/HL-1435 Read this Quick Setup Guide before using the printer. Before you can use the printer, you must set up the hardware and install the driver.
Safety Precautions To Use the Printer Safely Warning Indicates warnings that must be observed to prevent possible personal injury. Note Indicates cautions that must be observed to use the printer properly or prevent damage to the printer. Hint Indicates notes and useful tips to remember when using the printer. User's Guide Indicates reference to the User's Guide that is on the CD-ROM we have supplied. Warning There are high voltage electrodes inside the printer.
Table of Contents Regulations ........................................................................................................... 2 ■ Getting Started Carton Components ............................................................................................. 4 Control Panel ........................................................................................................ 5 Supplied CD-ROM .................................................................................................
Regulations Federal Communications Commission (FCC) Declaration of Conformity (For USA) Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard P.O. Box 6911 Bridgewater, NJ 08807-0911 USA Telephone: (908) 704-1700 declares, that the products Product name: Model number: Laser Printer HL-1430, HL-1435 HL-14 complies with Part 15 of the FCC Rules.
FDA Regulations (100 to 120 volt Model Only) U.S. Food and Drug Administration (FDA) has implemented regulations for laser products manufactured on and after August 2, 1976. Compliance is mandatory for products marketed in the United States. One of the following labels on the back of the printer indicates compliance with the FDA regulations and must be attached to laser products marketed in the United States. MANUFACTURED: Brother Industries, Ltd.
■ Getting Started Carton Components Printer 2 1 Face-down Output Tray Support Flap (Support Flap) 2 Face-down Output Tray (Top Output Tray) 3 Front Cover 4 Paper Tray 5 Manual Feed Paper Guides 6 Manual Feed Slot 7 Control Panel 1 7 3 6 5 CD-ROM (including User's Guide) 4 Quick Setup Guide Drum Unit Assembly (with Toner Cartridge included) AC Power Cord Carton components may differ from one country to another. Save all packing materials and the printer carton.
Control Panel Cancel Printing Button Reprinting Drum Ready Paper Alarm Toner Data Press the button one time and the printer will stop printing and eject the paper When the Data LED is off, press and hold the button until all the LEDs light. The printer will reprint the last job.
Supplied CD-ROM You can find a variety of information on the CD-ROM. 3 Mac® OS 8.6 to 9.2 Users Mac® OS X 10.1 to 10.2 Users 1 4 3 2 5 4 1 5 6 2 1 Initial Setup Instructional movie for printer setup and driver installation. 2 Install Software Installs the printer driver and utilities. 3 Documentation View the Printer User's Guide and Quick Setup Guide in PDF format. (Viewer included) 4 Brother Solutions Center The Brother Solutions Center (http://solutions.brother.
Step 1 Setting Up Your Printer For Windows® Users Setting Up Your Printer 1 Insert the CD-ROM into the CD-ROM Drive For Macintosh® Users Do NOT connect the interface cable. Connecting the interface cable is done when installing the driver. Windows® USB Do NOT connect the interface cable. Connecting the interface cable is done when installing the driver. 1 Insert the CD-ROM into your CD-ROM drive. Double-click the Start Here icon or Start Here OS X icon. Follow the on-screen instructions. Mac® OS 8.
Step 1 Setting Up Your Printer 2 Install the Drum Unit Assembly Do NOT connect the interface cable. Connecting the interface cable is done when installing the driver. 1 4 Put the drum unit assembly into the printer. 5 Close the front cover of the printer. Open the front cover. Front cover 2 Unpack the drum unit assembly. Remove the protective part. Drum unit assembly Protective part 3 8 Rock it from side to side several times to distribute the toner evenly inside the assembly.
1 Pull the paper tray completely out of the printer. 4 Setting Up Your Printer 3 Load Paper in the Paper Tray Put paper in the paper tray. Check that the paper is flat in the tray and below the maximum paper mark. Windows® USB Up to here. Paper guide release lever Windows® Parallel While pressing the paper guide release lever, slide the adjusters to fit the paper size. Check that the guides are firmly in the slots. 5 Put the paper tray firmly back in the printer.
Step 1 Setting Up Your Printer 4 Print a Test Page Do NOT connect the interface cable. Connecting the interface cable is done when installing the driver. 4 After the printer has finished warming up, the Ready LED stops blinking and stays green. Extend the Support flap. Ready Paper Alarm Toner Data 1 Make sure that the printer power switch is off. 5 Press the control panel button. The printer prints a test page. Check that the test page has printed correctly.
Step 2 Installing the Driver Setting Up Your Printer Follow the appropriate instructions on this page for your operating system and interface cable. The screens for Windows® in this Quick Setup Guide are based on Windows® XP. The screens for Mac® OS X in this Quick Setup Guide are based on Mac® OS X 10.1. Windows® USB For USB Interface Cable Users ............................Go to page 12 Windows® Parallel For Parallel Interface Cable Users.......................
Step 2 Installing the Driver For USB Interface Cable Users 1. Installing the Driver and Connecting the Printer to Your PC If the Found New Hardware Wizard appears on your PC, click the Cancel button. 1 2 A C L E C N 3 Select the USB interface. 4 Click the Install button. 5 Click the Next button. Follow the on-screen instructions. Make sure the USB interface cable is NOT connected to the printer, and then begin installing the driver. If you have already connected the cable, remove it.
Setting Up Your Printer When this screen appears, make sure the printer power switch is on. Connect the USB interface cable to your PC, and then connect it to the printer. Click the Next button. 2. Setting Your Printer as the Default Printer (For Windows® 2000/XP Users Only) 1 Click Start and then Printers and Faxes. 2 Select the Brother HL-14XX series icon. 3 From the File menu, select Set as Default printer. Installing the Driver Windows® USB 6 7 Click the Finish button.
Step 2 Installing the Driver For Parallel Interface Cable Users Connecting the Printer to Your PC and Installing the Driver 1 Click Connect the interface cable & Install the driver/utility from the Initial Setup menu. 2 Select the Parallel interface. 3 5 If the Found New Hardware Wizard appears on your PC, click the Cancel button. C Turn off the printer power switch. 6 4 Turn on the printer power switch. N A L E C Click the Next button when the movie finishes.
8 Click the Next button. Follow the on-screen instructions. 9 Click the Finish button. Setting Up Your Printer Click the Install button. Installing the Driver Windows® Parallel 7 The Setup is now complete.
Step 2 Installing the Driver For USB Interface Cable Users For Mac® OS 8.6 to 9.2 Users Installing the Driver & Connecting the Printer to your Macintosh 1 Click Connect the interface cable & Install the driver/utility from the Initial Setup menu. 4 Connect the USB interface cable to your Macintosh, and then connect it to the printer. Do not connect the USB cable to the keyboard USB Port or a non-powered USB Hub. 2 3 Follow the on-screen instructions, and restart your Macintosh.
Setting Up Your Printer For USB Interface Cable Users For Mac® OS X 10.1 to 10.2 Users Installing the Driver & Connecting the Printer to your Macintosh 1 Click Connect the interface cable & Install the driver/utility from the Initial Setup menu. 4 Connect the USB interface cable to your Macintosh, and then connect it to the printer. Do not connect the USB cable to the keyboard USB Port or a non-powered USB Hub. 5 Select Applications from the Go menu. 6 Open the Utilities folder.
Step 2 Installing the Driver For USB Interface Cable Users 7 Open the Print Center icon. 8 Click the Add Printer... button. A Select Quit Printer Center from the Printer Center menu. The setup is now complete. 18 9 Select USB. 0 Select HL-14XX series, and then click the Add button.
■ Other Information Shipment of the Printer If for any reason you must ship your Printer, carefully package the Printer in the original packing to avoid any damage during transit. It is strongly recommended that you save and use the original packaging. The Printer should also be adequately insured with the carrier. When shipping the Printer, the DRUM UNIT assembly and TONER CARTRIDGE must be removed from the Printer and placed in the foil bag.
■ Options Options You can expand the capability of the printer by adding IR-1000. User's Guide Chapter 4. Ir-DA Interface (Windows® 95/98/2000/Me and Windows NT® 4.0 only) IR-1000 The IR-1000 connects to the parallel interface for infrared wireless printing. Optional accessories may differ from one country to another.
LJ7226001 Printed in China ©2003 Brother Industries, Ltd.
