User Manual

ManualsBrandsBrother ManualsAll in One PrinterDCP-J125

LX6274054

CEE-ENG

Printed in China

Before you can use the machine, read this Quick Setup Guide

for the correct setup and installation.

Turn the sheet over.

Quick Setup Guide

DCP-J125

Install the ink cartridges

d. Unpack the ink cartridge.

Turn the green knob on the protective yellow cap clockwise until it clicks to release the vacuum

seal, then remove the cap a.

If all lines are clear and visible, o

press (Yes) to finish the quality

check.

If you can see missing short lines, o

press

(No) and follow the steps

on the LCD.

Set the LCD contrast (if needed)

Check the print quality

c. Remove the green protective part a.

Poor

Set the date and time

a. Press Menu.

b. Press a or b to choose

General Setup, and then press OK.

c. Press a or b to choose

LCD Settings, and press OK.

d. Press a or b to choose

LCD Contrast, and then press OK.

e. Press d or c to choose the contrast level,

and then press OK.

f. Press Stop/Exit.

a. Press Menu.

b. Press a or b to choose

Initial Setup, and

then press OK.

c. Press a or b to choose

Date&Time, and then

press OK.

Unpack the machine and check the components

Inbox Ink

Cartridges [x4]

Black

Yellow

Cyan

Magenta

Power Cord

Installation CD-ROM

Documentation CD-ROM

Control Panel

The components of your box may differ depending on your country.

Approx. 65% yield of the replacement cartridge. For details, see Consumable items in the Basic

User’s Guide.

Plastic bags are used in the packaging of your machine. To avoid

danger of suffocation, please keep these bags away from babies

and children.

WARNING

a. Pull out the paper tray. b. Lift the output paper tray cover a.

Load plain A4 paper

c. Press and slide the

paper side guides

a and paper length

guide b to fit the

paper size.

Make sure that the

triangular marks c

on the paper side

guides a and paper

length guide b line

up with the mark for

the paper size you

are using.

d. Fan the stack of paper well.

e. Gently put the paper into

the paper tray. Check that

the paper is flat in the tray.

f. Gently adjust the paper side

guides to the paper with

both hands.

Make sure the paper side

guides touch the edges of

the paper.

g. Close the output paper tray

cover and slowly push the

paper tray back into the

machine.

h. Pull out the paper support a

until it clicks, and then unfold

the paper support flap b.

IMPORTANT

DO NOT push the paper in too far.

a. Connect the power cord.

The machine must be ﬁ tted with an earthed plug.

WARNING

Connect the power cord

Choose your language

a. Press a or b to choose your

language and press OK.

b. Press a or b to choose Yes

or No and press OK.

Note

If you set the wrong language,

you can change it again after

setting the date and time.

(For details see Changing LCD

language in chapter 1 in the

Advanced User’s Guide on the

documentation CD-ROM.)

e. Install each ink cartridge in the direction of the arrow on the label.

Take care to match the colour of the lever a with the cartridge

colour b.

Start Here

WARNING

WARNING indicates a

potentially hazardous

situation which, if not

avoided, could result in

death or serious injuries.

a. The LCD shows No Ink Cartridge.

b. Open the ink cartridge cover a.

a. When the preparation process has

finished, the LCD shows

Set Paper and Press Start.

Press Colour Start.

Note

Save all packing materials and the box in case for any •

reason you must ship your machine.

A USB cable is not included. •

You need to purchase a USB 2.0 cable that is no more

than 2 metres long.

a. Remove the protective tape and film covering the

machine, and also from the LCD.

b. Remove the plastic bag a containing the ink cartridges

from on top of the paper tray.

c. Make sure you have all components.

f. Gently push the ink cartridge until it clicks. After all the ink

cartridges are installed close the ink cartridge cover.

d. To enter the last two digits of the year, press

a, b, d or c to select a number and press OK.

To save the year, press a, b, d or c to select

and press OK.

1 23

789

Year:2010

(e.g. Enter 10 for 2010.)

IMPORTANT

DO NOT connect the

USB cable yet.

Note

The Warning LED on the

control panel will stay on

until you have installed

the ink cartridges.

Note

Make sure you install the Inbox Ink Cartridges

included with your machine ﬁ rst.

e. Repeat for month/day/time in 24-hour format.

f. Press Stop/Exit.

Note

If you make a mistake and want to start again,

press Stop/Exit to go back to step a.

b. Check the quality of the four colour blocks a

on the sheet.

(black/yellow/cyan/magenta)

Note

Do not throw away the green protective part.

You will need it if you transport the machine.

Note

The machine will prepare the ink tube system for printing.

This process will take approximately four minutes.

Do not turn off the machine.

a. Attach the cover of the control

panel to the machine.

Attachment of the cover of

the control panel

Summary of content (2 pages)

PAGE 1
Quick Setup Guide Before you can use the machine, read this Quick Setup Guide for the correct setup and installation. DCP-J125 LX6274054 CEE-ENG Printed in China Attachment of the cover of the control panel Unpack the machine and check the components 1 Start Here WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injuries. Note • Save all packing materials and the box in case for any reason you must ship your machine.
PAGE 2
What is Innobella™? Get inspired. Double-click the Brother CreativeCenter icon on your desktop to access a FREE web site with many ideas and resources for personal and professional use. LX6274054 For Innobella™ is a range of genuine consumables offered by Brother. The name “Innobella™” derives from the words “Innovation” and “Bella” (meaning “Beautiful” in Italian) and is a representation of the “innovative” technology providing you with beautiful and long lasting print results. http://www.brother.