User`s guide
Table Of Contents
- SOFTWARE USER’S GUIDE
- Table of Contents
- 1 Using the machine as a printer
- Using the Brother printer driver
- How to print your document
- Simultaneous printing and faxing
- Printer operation key
- Printer driver settings (For Windows®)
- How to access the printer driver settings (For Windows®)
- Features in the PCL printer driver (For Windows®)
- Features in the PS (PostScript®) Brother printer driver (DCP-7025, MFC-7225N and MFC-7820N only) (For Windows®)
- Status Monitor (Windows® only)
- 2 How to scan using Windows®
- Scanning a document using WIA driver (For Windows® XP only)
- Scanning a document using the TWAIN driver
- Using the Scan key (For USB or Parallel cable users)
- Using ScanSoft® PaperPort® 9.0SE and OmniPage® OCR
- 3 Using ControlCenter2.0 (For Windows®)
- 4 Using MFC Remote Setup (For Windows®) (not available for DCP-7010 and DCP-7025)
- 5 Using Brother PC-FAX software (For Windows®) (not available for DCP-7010 and DCP-7025)
- PC-FAX sending
- Speed-Dial setup
- Brother Address Book
- Setting up a Member in the Address Book
- Setting up a Group for Broadcasting
- Editing Member information
- Deleting a Member or Group
- Exporting the Address Book
- Importing to the Address Book
- Sending a file as a PC-FAX using the Facsimile style user interface
- Sending a file as a PC-FAX using the Simple style user interface
- Setting up PC-FAX receiving
- 6 Network Scanning (For Windows®) (MFC-7225N, MFC-7820N or models with the optional NC-2200w Only)
- 7 Using your machine with a Macintosh®
- Setting up your USB-equipped Apple® Macintosh®
- Using the Brother printer driver with your Apple® Macintosh® (Mac OS® X)
- Using the Brother printer driver with your Apple® Macintosh® (Mac OS® 9.1 to 9.2)
- Using the PS driver with your Apple® Macintosh® (DCP-7025, MFC-7225N and MFC-7820N only)
- Sending a fax from your Macintosh® application (not available for DCP-7010 and DCP-7025)
- Scanning from a Macintosh®
- Configuring Network Scanning
- Using Presto!® PageManager®
- Using ControlCenter2.0 (For Mac OS® X 10.2.4 or greater)
- MFC Remote Setup (Mac OS® X 10.2.4 or greater) (not available for DCP-7010 and DCP-7025)
- Index
- brother ARL/ASA/NZ
How to scan using Windows
®
2 - 4
2
Scanning a document into the PC
(DCP-7010, DCP-7025, MFC-7420 and MFC-7820N Only)
There are two ways in which you can scan a whole page. You can either use the ADF (automatic document
feeder) or the Flatbed scanner glass. (ADF is not available for DCP-7010.)
If you would like to scan and then crop a portion of the page after pre-scanning the document, you will need
to use the scanner glass (Flatbed). (See Pre-Scanning to crop a portion you want to scan on page 2-9.)
Scanning a document using the ADF (not available for DCP-7010)
1
Load your document.
2
Select the Document Feeder from the Paper source
drop-down list box (A).
3
Select the picture type (B).
4
Select the Paper size from the drop-down list box (D).
5
If you require advanced settings, click on the tab Adjust
the quality of the scanned picture (C). You can select
Brightness, Contrast, Resolution and Picture Type
from the Advanced Properties. Click the OK button
after you choose your settings.
Note
■
You can select a resolution of up to 1200 dpi.
■
For resolutions greater than 1200 dpi, use the Brother Scanner Utility. (See
Brother Scanner Utility (not
available for MFC-7220 and MFC-7225N)
on page 2-6.)
6
To start scanning your document, click the Scan button in the Scan dialog box.
A
B
C
D