Brother Laser Printer USER’S GUIDE HL-2140 HL-2150N HL-2170W For visually-impaired users You can read this manual with Screen Reader ‘text-to-speech’ software. You must set up the hardware and install the driver before you can use the printer. Please use the Quick Setup Guide to set up the printer. You can find a printed copy in the box. Please read this User’s Guide thoroughly before you use the printer. Keep the CD-ROM in a convenient place so you can use it quickly if you need to.
Using this guide Symbols used in this guide We use the following icons throughout this User’s Guide: Warnings tell you what to do to prevent possible personal injury. Electrical Hazard icons alert you to a possible electrical shock. Hot Surface icons warn you not to touch machine parts that are hot. Cautions specify procedures you must follow or avoid to prevent possible damage to the printer or other objects. Improper Setup icons alert you to devices and operations that are not compatible with the printer.
Safety precautions To use the printer safely WARNING There are high voltage electrodes inside the printer. Before you clean the inside of the printer, make sure that you have turned off the power switch and unplugged the printer from the AC power outlet. DO NOT handle the plug with wet hands. Doing this might cause an electrical shock. Always make sure the plug is fully inserted. After you have just used the printer, some internal parts of the printer will be extremely hot.
DO NOT remove or damage the caution labels located on or around the fuser. DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner dust to ignite inside the vacuum cleaner, potentially starting a fire. Carefully clean the toner dust with a dry, lint-free cloth and dispose of it according to local regulations. DO NOT use flammable substances or any type of spray to clean the inside or outside of the machine. Doing this may cause a fire or electrical shock.
Trademarks The Brother logo is a registered trademark of Brother Industries, Ltd. Apple, the Apple Logo, Macintosh and TrueType are registered trademarks of Apple Inc. in the United States and other countries. Hewlett Packard is a registered trademark and HP LaserJet 6P, 6L, 5P, 5L, 4, 4L 4P, III, IIIP, II, and IIP are trademarks of Hewlett-Packard Company. Microsoft, MS-DOS, Windows are registered trademarks of Microsoft Corporation in the U.S. and other countries.
Table of Contents 1 About this Printer 1 What is in the box? ....................................................................................................................................1 Interface cable .....................................................................................................................................1 Front view ............................................................................................................................................
Toner cartridge ..................................................................................................................................61 Drum unit ...........................................................................................................................................68 Cleaning ..................................................................................................................................................73 Cleaning the outside of the printer..................
C Appendix (for USA and Canada) 122 Brother numbers ....................................................................................................................................122 Important information: regulations .........................................................................................................125 Federal Communications Commission (FCC) Declaration of Conformity (USA only) .....................125 Industry Canada Compliance Statement (Canada only) ........................
1 About this Printer 1 1 What is in the box? 1 When you unpack the printer, make sure that you have all of the following parts. Printer Quick Setup Guide CD-ROM Drum unit and starter toner cartridge assembly AC power cord Interface cable 1 The interface cable is not a standard accessory. Purchase the appropriate cable for the interface you are using. USB cable Please make sure you use a USB 2.0 interface cable that is no longer than 6 feet (2 meters).
About this Printer Front view 1 1 1 2 11 3 10 4 9 5 8 6 7 1 Face-down output tray support flap 2 (support flap 2) 1 2 Face-down output tray support flap 1 (support flap 1) 3 Control panel 2 4 Manual feed paper guide 5 Manual feed slot 6 Manual feed slot cover 7 Paper tray 8 Front cover 9 Power switch 10 Ventilation hole 11 Face-down output tray 1 For details about the support flap 2, see page 96. 2 For details about the control panel, see Chapter 4.
About this Printer Back view 1 1 1 6 5 2 4 3 1 Back cover (back output tray) 2 AC power connector 3 HL-2150N / HL-2170W: Network status LEDs (Light Emitting Diodes) 4 HL-2150N / HL-2170W: 10/100BASE-TX port 5 HL-2170W: Wireless setup button 6 USB interface connector 3
About this Printer Positioning the printer 1 1 Read the following before you use the printer. Power supply 1 Use the printer within the recommended power range. Power source: USA and Canada: AC 110 to 120 V, 50/60 Hz Europe and Australia: AC 220 to 240 V, 50/60 Hz The power cord, including extensions, should be no longer than 5 meters (16.5 feet). Do not share the same power circuit with other high-powered appliances, such as an air conditioner, copier, shredder and so on.
2 Printing Methods 2 About paper 2 2 Type and size of paper 2 The printer loads paper from the installed paper tray or the manual feed slot. The names for the paper trays in the printer driver and this guide are as follows: Paper tray Tray 1 Manual feed slot Manual When looking at this page in the electronic file, you can jump to the page for each printing method by clicking p in the table.
Printing Methods Tray 1 Paper size 1 Manual A4, Letter, Legal , B5 (ISO), Executive, A5, A6, B6 (ISO), Folio, Post Card Width: 76.2 to 220mm (3 to 8.7 in.) Number of sheets (80 g/m2 / 20 lb) 250 sheets Single sheet Envelope size N/A COM10 1 Length: 116 to 406.4 mm (4.57 to 16 in.) 2 Legal size paper is not available in some regions outside the USA and Canada.
Printing Methods Types of envelopes 2 Most envelopes will be suitable for your printer. However, some envelopes may have feed and print quality problems due to the way they have been made. A suitable envelope should have edges with straight, wellcreased folds and the leading edge should not be thicker than two pieces of paper. The envelope should lie flat and not be of baggy or flimsy construction.
Printing Methods Unprintable area 2 The area of the paper that cannot be printed on is shown in the table below: Portrait 2 1 2 4 3 A4 Letter Legal B5 (ISO) Executive A5 A6 B6 1 4.23 mm (0.16 in.) 4.23 mm (0.16 in.) 4.23 mm (0.16 in.) 4.23 mm (0.16 in.) 4.23 mm (0.16 in.) 4.23 mm (0.16 in.) 4.23 mm (0.16 in.) 4.23 mm (0.16 in.) 2 6.01 mm (0.24 in.) 6.35 mm (0.25 in.) 6.35 mm (0.25 in.) 6.01 mm (0.24 in.) 6.35 mm (0.25 in.) 6.01 mm (0.24 in.) 6.01 mm (0.24 in.) 6.01 mm (0.
Printing Methods Printing methods Printing on plain paper, bond paper and transparencies Printing on plain paper, bond paper and transparencies from the paper tray 2 2 2 (For the recommended paper to use, see About paper on page 5.) a Pull the paper tray completely out of the printer. b While pressing the green paper-guide release lever, slide the paper guides to fit the paper size. Make sure that the guides are firmly in the slots.
Printing Methods Note For Legal size paper, press in the inside latches and pull out the back of the paper tray. (Legal size paper is not available in some regions.) 2 c Put paper in the tray, and make sure that the paper is below the maximum paper mark (1). The side to be printed on must be face down. 1 d e Put the paper tray firmly back in the printer. Make sure that it is completely inserted into the printer.
Printing Methods f Choose the following from the printer driver: Paper Size ............................ (1) Media Type ........................... (2) Paper Source ....................... (3) and any other settings.
Printing Methods g Send the print data to the printer. Note • The Error LED on the control panel will light up to indicate No paper if the power switch is turned on before you put paper or transparencies in the tray. You can clear this error indication by pressing Go. • When printing on transparencies, remove each transparency as soon as it has been printed. Stacking the printed transparencies may cause a paper jam or the transparency to curl.
Printing Methods Printing on plain paper, bond paper or transparencies from the Manual feed slot 2 (For the recommended paper to use, see About paper on page 5.) Note The printer automatically turns on the Manual Feed mode when you put paper in the manual feed slot. a 2 Lift up the support flap 1 (1) to prevent paper from sliding off the face-down output tray, or remove each page as soon as it comes out of the printer. 1 b Open the manual feed slot cover.
Printing Methods d Using both hands, put one piece of paper or one transparency in the manual feed slot until the front edge of the paper or transparency touches the paper feed roller. When you feel the machine pull in the paper, let go. 2 Note • Put the paper into the manual feed slot with the side to be printed face up. • Make sure that the paper or transparency is straight and in the correct position on the manual feed slot.
Printing Methods e Choose the following from the printer driver: Paper Size ............................ (1) Media Type ........................... (2) Paper Source ....................... (3) and any other settings.
Printing Methods f g Send the print data to the printer. After the printed page comes out of the printer, put in the next sheet of paper or transparency as in Step d above. Repeat for each page that you want to print. Note • The Error LED on the control panel will flash to indicate No paper in the manual feed slot until you put a sheet of paper or transparency in the manual feed slot. • When printing on transparencies, remove each transparency as soon as it has been printed.
Printing Methods Printing on thick paper, labels and envelopes 2 When the back output tray is pulled down, the printer has a straight paper path from the manual feed slot through to the back of the printer. Use this paper feed and output method when you want to print on thick paper, labels or envelopes. (For the recommended paper to use, see About paper on page 5 and Types of envelopes on page 7.) Note The printer automatically turns on the Manual Feed mode when you put paper in the manual feed slot.
Printing Methods d Using both hands, put one piece of paper or one envelope in the manual feed slot until the front edge of the paper or envelope touches the paper feed roller. When you feel the machine pull in the paper, let go. 2 Note • Put the paper into the manual feed slot with the side to be printed face up. • Make sure that the paper or envelope is straight and in the proper position on the manual feed slot.
Printing Methods Note • When you use Envelope #10, choose Com-10 for the Paper Size. • For other envelopes which are not listed in the printer driver, such as Envelope #9 or Envelope C6, choose User Defined... (For more information on envelope sizes, see Paper size on page 106.) 2 Macintosh® printer driver Paper Size ............................ (1) Media Type ........................... (2) Paper Source ....................... (3) and any other settings.
Printing Methods f g Send the print data to the printer. After the printed page comes out of the printer, put in the next sheet of paper or envelope as shown in Step d. Repeat for each page that you want to print. Note • The Error LED on the control panel will flash to indicate No paper in the manual feed slot until you put a sheet of paper or envelope in the manual feed slot. • Remove each sheet or envelope as soon as it has been printed. Stacking sheets or envelopes may cause the paper to jam or curl.
Printing Methods Note • If an envelope is creased after it is printed, turn the next one around 180° when you put it in the manual feed slot, and then in the printer driver choose the Advanced tab, select Page Setting, and check the Reverse Print box. As an alternative you can change the printing direction in your software application. • If the DL size double flap envelope is creased after printing, choose DL Long Edge in Paper Size, from the Basic tab.
Printing Methods Duplex printing 2 The supplied printer drivers for Windows® 2000/XP/XP Professional x64 Edition, Windows Vista™, Windows Server® 2003/Windows Server® 2003 x64 Edition and Mac OS® X 10.3 or greater all enable duplex printing. For more information about how to choose the settings, see the Help text in the printer driver. Guidelines for printing on both sides of the paper 2 2 If the paper is thin, it may wrinkle.
Printing Methods c Remove the printed even-numbered pages from the output tray and put them back in the paper tray with the side to be printed on (blank side) face down. Follow the instructions on the computer screen. 2 d The printer will now automatically print all the odd-numbered pages on the other side of the paper. Note When you put paper in the paper tray, first empty the tray. Next, put the printed pages in the tray, with the printed side face up.
Printing Methods c Using both hands, slide the manual feed slot paper guides to the width of the paper that you are going to use. 2 d Using both hands put the paper in the manual feed slot with the side that is going to be printed on first facing up. Follow the instructions on the computer screen. Repeat this step until you have printed all the even-numbered pages.
Printing Methods Paper orientation for manual duplex printing 2 The printer prints the second page first. If you print 10 pages on 5 sheets of paper, it will print page 2 and then page 1 on the first sheet of paper. It will print page 4 and then page 3 on the second sheet of paper. It will print page 6 and then page 5 on the third sheet of paper, and so on.
3 Driver and Software 3 Printer driver 3 A printer driver is software that translates data from the format used by a computer to the format that a particular printer needs. Typically, this format is page description language (PDL). 3 The printer drivers for the supported versions of Windows® and Macintosh® are on the CD-ROM we have supplied or on the Brother Solutions Center at http://solutions.brother.com. Install the drivers by following the Quick Setup Guide.
Driver and Software Windows® printer driver (HL-2150N/ HL-2170W Only) Windows® 2000 Professional p p Windows® XP Home Edition p p Windows® XP Professional p p Windows Vista™ p p Windows Server® 2003 p p Windows® XP Professional x64 Edition p p Windows Server® 2003 x64 Edition p p Mac OS® X 10.2.
Driver and Software You can change the following printer settings when you print from your computer. Paper Size Multiple Page Orientation Copies 3 Media Type Paper Source Resolution Toner Save Mode Print Setting Manual Duplex printing 1 Watermark 2 Scaling Job Spooling 2 Quick Print Setup 2 Sleep Time Macro 2 3 Header-Footer Print 2 Density adjustment 2 Error Message Printout 2 Improve Print Output 1 These settings are not available with the Mac OS® 10.2.4.
Driver and Software Features in the printer driver (for Windows®) 3 (For more information, see the Help text in the printer driver.) Note • The screens in this section are from Windows® XP. The screens on your computer will vary depending on your operating system. Windows® 3 ® • If you are using 2000, XP, Windows Vista™ or Windows Server 2003, you can access the Printing Preferences dialog box by clicking Printing Preferences... in the General tab of the Printer Properties dialog box.
Driver and Software Paper Size 3 From the drop-down box choose the Paper Size you are using. Multiple Page 3 The Multiple Page selection can reduce the image size of a page allowing multiple pages to be printed on one sheet of paper or can enlarge the image size for printing one page on multiple sheets of paper. 3 Page Order 3 When N in 1 option is selected, the page order can be selected from the drop-down list.
Driver and Software Media Type 3 You can use the following types of media in your printer. For the best print quality, select the type of media that you wish to use. Plain Paper Thin Paper Thick Paper Thicker Paper Envelopes Env. Thick Env. Thin Recycled Paper Bond Paper Transparencies 3 Note • When using ordinary plain paper (72.5 g/m2 to 95 g/m 2 / 19 to 25 lb) choose Plain Paper. When using heavier weight paper or rough paper choose Thick Paper or Thicker Paper.
Driver and Software Advanced tab 3 1 2 3 4 5 3 Change the tab settings by clicking one of the following icons: Print Quality (1) Duplex (2) Watermark (3) Page Setting (4) Device Options (5) Print Quality 3 Resolution You can change the resolution as follows: • HQ 1200 • 600 dpi • 300 dpi Toner Save Mode You can save running costs by turning on the Toner Save Mode, which reduces the print density (print appears lighter).
Driver and Software Print Setting You can manually change the print setting. • General This is a printing mode for general printing of documents. • Graphics 3 This is the best mode for printing documents that contain graphics. • Office Document This is the best mode for printing office documents. • Manual You can change the settings manually by choosing Manual and clicking the Setting... button. You can set brightness, contrast and other settings.
Driver and Software Device Options 3 3 You can set the following in Printer Function: Job Spooling Quick Print Setup Sleep Time Macro (HL-2150N / HL-2170W only) Header-Footer Print Density adjustment Error Message Printout Improve Print Output 34
Driver and Software Job Spooling The printer keeps the last print job sent to it in memory. To reprint the last document, press the Go button and hold it down for about 4 seconds until all the LEDs light up in order (Toner, Drum, Error, Ready), and then release the Go button. Within 2 seconds press the Go button the number of times you want to reprint. If you don’t press the Go button within 2 seconds, a single copy will be printed.
Driver and Software Header-Footer Print When this feature is enabled, it will print the date and time on your document from your computer’s system clock and the PC login user name or the text you entered. By clicking Setting, you can customize the information. • ID Print If you select Login User Name, your PC login user name will print. If you select Custom and enter the text in the Custom edit box, the text you entered will print. Density adjustment Increase or decrease the print density.
Driver and Software Tray Settings tab 3 You can define the paper size for each paper tray and auto detect the serial number in the Tray Settings tab as follows. 3 1 2 Paper Source Setting (1) This feature identifies the paper size defined for each paper tray. • Paper Size This setting allows you to define which paper size is used for the tray and manual feed slot. Highlight the paper source you want to define and then choose the paper size from the pull-down menu.
Driver and Software Support tab 3 2 3 3 4 5 1 Visit the Genuine Supplies website (1) You can visit our website for original/genuine Brother supplies by clicking this button. Brother Solutions Center (2) The Brother Solutions Center (http://solutions.brother.com) is a website offering information about your Brother product including FAQs (Frequently Asked Questions), User’s Guides, driver updates and tips for using your printer.
Driver and Software Features in the printer driver (for Macintosh®) 3 This printer supports Mac OS® X 10.2.4 or greater. Note The screens in this section are from Mac OS® X 10.4. The screens on your Macintosh® will vary depending on your operating system. Page Setup 3 3 You can set the Paper Size, Orientation and Scale. Copies & Pages 3 You can set the Copies and Pages.
Driver and Software Cover Page (for Mac OS® X 10.4) 3 You can make the following cover page settings: 3 Print Cover Page If you want to add a cover page to your document, use this function. Cover Page Type Choose a template for the cover page. Billing Info If you want to add the billing information to the cover page, enter text in the Billing Info box. Layout 3 Pages per Sheet Choose how many pages will appear on each side of the paper.
Driver and Software Duplex Printing 3 Manual duplex (for Mac OS® X 10.3 or greater) Select Paper Handling. Choose Odd numbered pages and print, and then choose Even numbered pages and print.
Driver and Software Toner Save Mode You can conserve toner using this feature. When you set Toner Save Mode to On, print appears lighter. The default setting is Off. Note • We do not recommend Toner Save Mode for printing Photo or Gray Scale images. 3 • Toner Save Mode is not available for HQ 1200 resolution. Media Type You can change the media type to one of the following: • Plain Paper • Thin Paper • Thick Paper • Thicker Paper • Bond Paper • Transparencies • Envelopes • Env. Thick • Env.
Driver and Software Advanced tab 3 Print Quality You can change the print quality as follows: • Photo This is a photograph mode (gradation priority). Choose this setting for printing photographs that have continuous gradation. You can represent soft contrasts between various shades of gray. • Graphics This is a graphics mode (contrast priority). Choose this setting for printing text and figures, such as business and presentation documents. You can represent sharp contrasts between shaded areas.
Driver and Software Improve Print Output This feature allows you to improve a print quality problem. • Reduce Paper Curl If you choose this setting, the paper curl may be reduced. If you are printing only a few pages, you do not need to choose this setting. We recommend that you change the printer driver setting in Media Type to a thin setting. 3 • Improve Toner Fixing If you choose this setting, the toner fixing on paper may be improved.
Driver and Software Uninstalling the printer driver 3 You can uninstall the printer driver that you have installed with the following steps. Note • This is not available if you installed the printer driver from the Windows Add a printer function. • After uninstalling, we recommend that you restart your computer to remove files that were in use during the uninstall.
Driver and Software Software 3 Software for network models (HL-2150N / HL-2170W only) 3 BRAdmin Light 3 BRAdmin Light is a utility for initial setup of Brother network connected devices. This utility can search for Brother products on your network, view the status and configure basic network settings, such as IP address. The BRAdmin Light utility is available for Windows® 2000/XP and Windows Vista™ and Windows Server® 2003, and Mac OS® X 10.2.4 or greater computers.
Driver and Software Automatic interface selection (HL-2150N / HL-2170W only) 3 This printer has an automatic interface selection feature that is turned on by default. This lets it automatically change the interface to USB or Ethernet depending on which interface is receiving data. Since the default setting is on for the automatic interface selection mode, simply connect the interface cable to the printer. Always turn off both your computer and printer when connecting or disconnecting the cable.
4 Control Panel 4 LEDs (Light Emitting Diodes) 4 This section refers to three LEDs Toner, Drum and Error, and a dual function Ready LED & Go button on the control panel. 1 Toner LED The Toner LED indicates when the Toner is low or at the end of its life. 2 Drum LED 1 2 3 The Drum LED indicates when the Drum is nearing the end of its life.
Control Panel LED Printer status Off The power switch is off. 4 Sleep mode The printer is in sleep mode. Pressing the Go button wakes up the printer from sleep mode to ready mode. Ready to print The printer is ready to print.
Control Panel LED Printer status Warming up The printer is warming up. Cooling down The printer is cooling down. Wait for a few seconds until the inside of the printer has cooled down. Receiving data The printer is either receiving data from the computer, processing data in memory or printing the data. Data remaining in memory There is remaining print data in the printer memory.
Control Panel LED Printer status Drum life end soon The drum unit is near the end of its life. We recommend that you get a new drum unit to replace the current one. See Replacing the drum unit on page 69. The Drum LED will turn on for 2 seconds and off for 3 seconds. 4 No paper fed tray1 Put paper in the tray. Then press the Go button. See Printing on plain paper, bond paper and transparencies on page 9. No paper fed manual feed slot Put paper in the manual feed slot.
Control Panel LED Printer status Drum error The corona wire needs to be cleaned. See Cleaning the corona wire on page 77. Put in a new drum unit. See Replacing the drum unit on page 69.
Control Panel Service call indications 4 If there is an error that cannot be cleared by the user, the printer will show that a service call is needed by lighting up all the LEDs as shown below. 4 If you see the service call indication shown above, turn off the power switch, and then turn it back on and try to print again.
Control Panel For example, the LED indication below shows a fuser unit failure. 4 Make a note of the indication, referring to the table on page 53, and report the error status to your dealer or Brother Customer Service. Note Make sure that the front cover is completely closed before you report a service call.
Control Panel Go button 4 The Go button has the following functions: Cancel printing Cancel only the printing job: While printing press the Go button for about 4 seconds until all the LEDs light up. The Ready and Error LEDs will flash as the job is being canceled. Cancel all the received jobs: To delete all jobs, press the Go button for about 4 seconds until all the LEDs light up and then release it. Press the Go button again. The Ready and Error LEDs will flash as the job is being canceled.
Control Panel Print a test page 4 You can use the Go button or the printer driver to print a test page. Using the Go button a b c d 4 Turn off the printer. Make sure that the front cover is closed and the power cord is plugged in. 4 Hold down the Go button as you turn on the power switch. Keep the Go button pressed down until the Toner, Drum and Error LEDs light up. Release the Go button. Make sure that the Toner, Drum and Error LEDs are off. Press the Go button again.
Control Panel Print a Printer Settings page 4 You can print the current settings using the control panel button or printer driver. Using the Go button a b c 4 Make sure that the front cover is closed and the power cord is plugged in. Turn on the printer and wait until the printer is in the Ready state. Press the Go button three times within 2 seconds. The printer will print the current printer settings page.
Control Panel Print Fonts (HL-2150N / HL-2170W only) 4 You can print a list of the internal fonts using the control panel button or printer driver. Using the Go button a b c d 4 Turn off the printer. Make sure that the front cover is closed and the power cord is plugged in. 4 Hold down the Go button as you turn on the power switch. Keep the Go button pressed down until the Toner, Drum and Error LEDs light up. Release the Go button. Make sure that the Toner, Drum and Paper LEDs are off.
Control Panel Network default settings (HL-2150N / HL-2170W only) 4 If you want to reset the print server back to its default settings (resetting all information such as the password and IP address information), follow these steps: Using the Go button a b c d 4 Turn off the printer. Make sure that the front cover is closed and the power cord is plugged in. 4 Hold down the Go button as you turn on the power switch. Keep the Go button pressed down until the Toner, Drum and Error LEDs light up.
5 Routine Maintenance 5 You will need to replace certain parts and clean the printer regularly. WARNING When you replace certain parts or clean the inside of the printer, remember the following: • If your clothes are smeared with toner, wipe off the toner with a dry cloth and immediately wash the clothes in cold water to avoid stains. • Be careful not to inhale toner. • After you have just used the printer, some internal parts of the printer will be extremely hot.
Routine Maintenance Toner cartridge 5 The life of the original toner cartridge that came with the printer may be either a starter 1, standard 2 or high yield 3 toner cartridge, and depends on the model and country you bought the printer in. 1 The starter toner cartridge will print approximately 1,000 A4 or Letter-size single-sided pages. Approx. cartridge yield is declared in accordance with ISO/IEC 19752.
Routine Maintenance Toner Life End message 5 The printer will stop printing until you replace the toner cartridge with a new one. 5 Replacing the toner cartridge 5 Note • To ensure high quality printing, we recommend that you use only genuine Brother toner cartridges. When you want to buy toner cartridges, call your dealer or Brother Customer Service. • We recommend that you clean the printer when you replace the toner cartridge. See Cleaning on page 73. a Make sure that the printer is turned on.
Routine Maintenance CAUTION We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner. To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration. 5 c Push down the green lock lever and take the toner cartridge out of the drum unit.
Routine Maintenance CAUTION DO NOT put a toner cartridge into a fire. It could explode, resulting in injuries. Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold water at once. To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations. 5 Note • Be sure to seal up the toner cartridge tightly in a suitable bag so that toner powder does not spill out of the cartridge. • Go to http://www.brother-usa.
Routine Maintenance CAUTION Wait to unpack the toner cartridge until immediately before you put it in the printer. If toner cartridges are left unpacked for a long time the toner life will be shortened. If an unpacked drum unit is put in direct sunlight or room light, the unit may be damaged. Put the toner cartridge in the drum unit immediately after you have removed the protective cover. To prevent any degradation to the print quality, DO NOT touch the shaded parts shown in the illustrations.
Routine Maintenance CAUTION For UK and other countries Brother machines are designed to work with toner of a particular specification and will work to a level of optimum performance when used with genuine Brother branded toner cartridges. Brother cannot guarantee this optimum performance if toner or toner cartridges of other specifications are used. Brother does not therefore recommend the use of cartridges other than genuine Brother branded cartridges with this machine.
Routine Maintenance g Clean the primary corona wire inside the drum unit by gently sliding the green tab from right to left and left to right several times. 1 5 CAUTION Be sure to return the tab to the home position (a) (1). If you do not, printed pages may have a vertical stripe. h Put the drum unit and toner cartridge assembly back in the printer. Close the front cover. CAUTION DO NOT turn off the printer power switch or open the front cover until the Ready LED lights up.
Routine Maintenance Drum unit 5 A new drum unit can print approximately 12,000 A4 or Letter size single-sided pages at 1 per/ job. Note • There are many factors that determine the actual drum life, such as the temperature, humidity, type of paper, type of toner used, number of pages per print job and so on. Under ideal conditions, the average drum life is estimated at approximately 12,000 pages. The actual number of pages that your drum will print may be significantly less than this estimate.
Routine Maintenance Replacing the drum unit 5 CAUTION While removing the drum unit, handle it carefully because it may contain toner. Every time you replace the drum unit, clean the inside of the printer. See Cleaning on page 73. When you replace the drum unit with a new one, you need to reset the drum counter by completing the following steps: 5 a Make sure that the printer is turned on and the Drum LED is blinking. Open the front cover.
Routine Maintenance c Take out the drum unit and toner cartridge assembly. CAUTION We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner. To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration. d Push down the green lock lever and take the toner cartridge out of the drum unit.
Routine Maintenance CAUTION Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold water at once. To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations. 5 Note • Be sure to seal up the drum unit tightly in a suitable bag so that toner powder does not spill out of the unit. • Go to http://www.brother-usa.com/environment/ for instructions on how to return the used toner cartridge to the brother collection program.
Routine Maintenance CAUTION Make sure that you put in the toner cartridge properly, or it may separate from the drum unit. g Put the drum unit and toner cartridge assembly back in the printer. 5 h i Close the front cover. Make sure that the Drum LED is now off.
Routine Maintenance Cleaning 5 Clean the outside and inside of the printer regularly with a dry, lint-free cloth. When you replace the toner cartridge or the drum unit, make sure that you clean the inside of the printer. If printed pages are stained with toner, clean the inside of the printer with a dry, lint-free cloth. Cleaning the outside of the printer 5 CAUTION Use neutral detergents. Cleaning with volatile liquids such as thinner or benzine will damage the surface of the printer.
Routine Maintenance c Wipe the outside of the printer with a dry, lint-free cloth to remove dust. d e Remove anything that is stuck inside the paper tray. f g Put the paper tray back in the printer. 5 Wipe the inside of the paper tray with a dry, lint-free cloth to remove dust. Plug the printer back in, and then turn on the power switch. Cleaning the inside of the printer a Turn off the printer power switch and then unplug the printer. b Open the front cover.
Routine Maintenance c Take out the drum unit and toner cartridge assembly. HOT SURFACE 5 After you have just used the printer, some internal parts of the printer will be extremely hot. Wait for the printer to cool down before you touch the internal parts of the printer. CAUTION We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner. Handle the toner cartridge carefully.
Routine Maintenance d Wipe the scanner window with a dry, lint-free cloth. 5 e f g Put the drum unit and toner cartridge assembly back in the printer. Close the front cover. Plug the printer back in, and then turn on the power switch.
Routine Maintenance Cleaning the corona wire 5 If you have print quality problems, clean the corona wire as follows: a Open the front cover. 5 b Take out the drum unit and toner cartridge assembly. CAUTION We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner. To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration.
Routine Maintenance c Clean the primary corona wire inside the drum unit by gently sliding the green tab from right to left and left to right several times. 1 5 CAUTION Be sure to return the tab to the home position (a) (1). If you do not, printed pages may have a vertical stripe. d Put the drum unit and toner cartridge assembly back in the printer. Close the front cover.
6 Troubleshooting 6 You can correct most problems by yourself. If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at http://solutions.brother.com. Identifying your problem First, check the following: 6 6 The AC power cord is connected properly and the printer is turned on. All of the protective parts have been removed. The toner cartridges and drum unit are installed properly. The front cover and fuser cover are fully closed.
Troubleshooting Error messages in the Status Monitor 6 The Status Monitor will report problems with the printer. Take the proper action by referring to the following table. The default setting for the Status Monitor is off. If you want to turn the status monitor on, follow these steps: For Windows® users Click the Start button, All Programs 1, your printer (e.g Brother HL-2140), and then Status Monitor. 1 Programs for Windows® 2000 users For Macintosh® users (Mac OS® X 10.
Troubleshooting Error message No Paper Fed Manual Slot Action If the manual feed slot is empty, put a piece of paper in it. Make sure you use paper that meets Brother’s recommended paper specifications. See About paper on page 5. Load the same size paper that you selected in the current driver setting. Paper Jam Tray 1 Paper Jam Inside Clear the jammed paper from the indicated area. See Paper jams and how to clear them on page 85.
Troubleshooting Error message printout 6 The printer can also report problems by printing an error message. Use the table below to identify and clear the error message. Error message MEMORY FULL Action Press the Go button to print the remaining data in the printer memory. Cancel the print job if you want to delete the remaining data in the printer memory. See Go button on page 55. Reduce the complexity of your document or reduce the print resolution.
Troubleshooting Paper handling 6 First, make sure that you are using paper that meets Brother’s recommended paper specifications. (See About paper on page 5.) Problem The printer does not feed paper. Recommendation If there is paper in the paper tray, make sure it is straight. If the paper is curled, flatten it before printing. Sometimes it is helpful to remove the paper. Turn the stack over and put it back in the paper tray. Reduce the amount of paper in the paper tray, and then try again.
Troubleshooting Problem Recommendation The paper slides off the back output tray. Follow these steps: a Remove the output tray support flap 1 (1) from the top of the printer by first lifting the flap up. Then push the flap to the left or right to release one of the posts (2) on the flap and pull up. 1 6 2 b Attach the support flap 1 (1) to the back output tray by inserting the posts of the support flap one at a time into the holes of the back output tray.
Troubleshooting Paper jams and how to clear them 6 If a paper jam occurs, the printer will flash the Error LED as shown below. 6 HOT SURFACE After you have just used the printer, some internal parts of the printer will be extremely hot. When you open the front cover or back cover (back output tray) of the printer, DO NOT touch the shaded parts shown in the illustrations. Clear the jammed paper as follows.
Troubleshooting a Open the front cover. b Slowly take out the drum unit and toner cartridge assembly. The jammed paper will be pulled out with the drum unit and toner cartridge assembly. 6 CAUTION We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner. To prevent damage to the printer caused by static electricity, DO NOT touch the electrodes shown in the illustration. c Close the front cover.
Troubleshooting d Pull the paper tray completely out of the printer. 6 e Pull the jammed paper down and out of the printer. f Open the back cover (back output tray).
Troubleshooting g Pull the tab toward you to open the fuser cover (1). 1 6 h Pull the jammed paper out of the fuser unit. HOT SURFACE After you have just used the printer, some internal parts of the printer will be extremely hot. Wait for the printer to cool down before you touch the internal parts of the printer. i Close the back cover (back output tray).
Troubleshooting j Push down the green lock lever and take the toner cartridge out of the drum unit. Clear the jammed paper if there is any inside the drum unit. 6 CAUTION Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold water at once. To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
Troubleshooting k Put the toner cartridge back into the drum unit until you hear it lock into place. If you put the cartridge in properly, the green lock lever will lift automatically. l Open the front cover. Put the drum unit and toner cartridge assembly back in the printer. m n o Put the paper tray firmly back in the printer. 6 Close the front cover. Make sure that the Error LED is now off.
Troubleshooting Improving the print quality 6 If you have a print quality problem, print a test page first (see Print a test page on page 56). If the printout looks good, the problem is probably not the printer. Check the interface cable or try the printer on another computer. This section gives information on the following topics. Examples of poor print quality ABCDEFGH CDEF abcdefghijk defg ABCD abcde 01234 Faint Recommendation Check the printer’s environment.
Troubleshooting Examples of poor print quality Recommendation Make sure that you use paper that meets our specifications. See About paper on page 5. Choose Thick paper mode in the printer driver, or use thinner paper than what you are now using. Check the printer’s environment. Conditions such as high humidity can cause hollow print. See Positioning the printer on page 4. Hollow print Clean the primary corona wire inside the drum unit by sliding the green tab.
Troubleshooting Examples of poor print quality Recommendation If the problem is not solved after printing a few pages, the drum unit may have glue from a label stuck on the OPC drum surface. 75 mm (2.95 in.) 75 mm (2.95 in.) Clean the drum unit as follows: a 6 Put the print sample in front of the drum unit, and find the exact position of the poor print. White Spots on black text and graphics at 75 mm (2.95 in.) intervals 6 75 mm (2.95 in.) 75 mm (2.95 in.
Troubleshooting Examples of poor print quality Recommendation The drum unit may be damaged. Put in a new drum unit. See Replacing the drum unit on page 69. ABCDEFGH abcdefghijk ABCD abcde 01234 Black toner marks across the page The toner cartridge may be damaged. Put in a new toner cartridge. See Replacing the toner cartridge on page 62. Make sure that you use paper that meets our specifications. See About paper on page 5.
Troubleshooting Examples of poor print quality Recommendation Make sure that the paper is loaded properly. See Printing on plain paper, bond paper and transparencies from the paper tray on page 9. B DEFGH abc efghijk Check the paper type and quality. See About paper on page 5. A CD bcde 1 34 Turn over the stack of paper in the tray or try rotating the paper 180° in the input tray.
Troubleshooting Examples of poor print quality Recommendation Turn the paper over in the paper tray, and print again. (Excluding Letterhead paper) If the problem remains, lift up the support flaps as follows: a Lift up the output tray support flap 1 (1). 1 Curled 6 b Lift up the output tray support flap 2 (2). 2 c 1 Fold down the output tray support flap 1 (1) and fold down the output tray support flap 2 (2).
Troubleshooting Solving print problems Problem The printer prints unexpectedly or it prints garbage data. 6 Recommendation Make sure that the printer cable is not too long. We recommend that you use a USB cable that is no longer than 2 meters (6.5 feet). Make sure that the printer cable is not damaged or broken. If you are using an interface-switching device, remove it. Connect your computer directly to your printer, and then try again.
Troubleshooting Network problems (HL-2150N / HL-2170W only) 6 For problems concerning using your printer on a Network, see the Network User’s Guide on the CD-ROM we have supplied. Click Documentation on the menu screen. The Network User’s Guide in HTML format will be installed automatically when you install the driver. Click the Start button, All Programs 1, your printer, and then User’s Guide. You can also view the manuals in PDF format by accessing the Brother Solutions Center (http://solutions.
A Appendix A Printer specifications A Engine A Model HL-2140 Technology Print speed HL-2170W Electrophotographic 12 (A4 size/ Letter size) First print time Resolution HL-2150N Up to 22 ppm (A4 size) 3,Up to 23 ppm (Letter size) 3 Less than 10 sec Windows® 2000/XP/ XP Professional x64 Edition, Windows Vista™, Windows Server ® 2003/ Windows Server ® 2003 x64 Edition HQ1200 DOS N/A Mac OS ® X 10.2.
Appendix Controller A Model HL-2140 HL-2150N HL-2170W Processor 181MHz Memory Interface 8 MB 16 MB 32 MB USB 1 USB 1, USB 1, 10BASE-T/100BASETX Ethernet, Wireless LAN IEEE 802.
Appendix Software A Model Printer driver HL-2140 HL-2150N HL-2170W Windows® GDI printer driver for Windows® 2000/XP/XP Professional x64 Edition, Windows Vista™, Windows Server® 2003/Windows Server® 2003 x64 Edition PCL printer driver for Windows® 2000/XP/XP Professional x64 Edition, Windows Vista™, Windows Server® 2003/Windows Server® 2003 x64 Edition Macintosh® Macintosh printer driver for Mac OS® X 10.2.
Appendix Media specifications A Model Media types Media weights Media sizes HL-2140 HL-2150N HL-2170W Manual feed slot Plain paper, Bond paper, Recycled paper, Thin paper, Thick paper, Envelopes, Labels, Transparencies Paper tray Plain paper, Bond paper, Recycled paper, Thin paper, Transparencies 1 Manual feed slot 60 to 163 g/m2 (16 to 43 lb) Paper tray 60 to 105 g/m2 (16 to 28 lb) Manual feed slot Width: 76.2 to 220mm (3.0 to 8.66 in.) Length: 116 to 406.4 mm (4.57 to 16 in.
Appendix Other A Model HL-2140 Power consumption Noise level Printing Sound Pressure Sound power Ecology Power save Toner 1 save 1 HL-2150N HL-2170W Average 460 W at 25 °C (77 °F) Standby Average 80 W at 25 °C (77 °F) Sleep Average 5 W Printing 51 dB (A) Standby 30 dB (A) Printing LWAd = 6.7 Bell (A) Standby LWAd = 4.5 Bell (A) Average 7 W Average 8 W Yes Yes We do not recommend Toner Save Mode for printing Photo or Gray Scale images.
Appendix Important information for choosing your paper A This section gives information to help you choose paper to use with this printer. Note If you use paper that is not recommended, a paper jam or misfeed may occur in the printer. (See Recommended paper on page 6.) Before you buy a large quantity of paper A Make sure that the paper is suitable for the printer. Paper for plain paper copies A Paper is divided by usage, such as paper for printing and paper for copying.
Appendix Print surface A The characteristics of the face side and reverse side of a sheet of paper may vary a little. Usually, the opening side of the paper ream package is the print side. Follow the indications on the paper package. Typically, the print side is indicated by an arrow. Moisture content A Moisture content is the amount of water left in the paper after manufacture. It is one of the important characteristics of the paper.
Appendix Paper size Paper size A mm in. Letter 8.5 × 11 in. Legal 8.5 × 14 in. Executive 7.25 × 10.5 in. A4 210 × 297 mm A5 148 × 210 mm A5 Long Edge 210 × 148 mm A6 105 × 148 mm Envelope Monarch 3.875 × 7.5 in. Envelope Com-10 4.12 × 9.5 in. Envelope DL 110 × 220 mm Envelope C5 162 × 229 mm B5 (JIS) 182 × 257 mm B5 (ISO) 176 × 250 mm B6 (ISO) 125 × 176 mm 8.5 × 13 in. Folio Post Card 100 × 148 mm A4 Long 210 × 405 mm Envelope DL-L 220 × 110 mm 3×5 A 3 × 5 in.
Appendix Symbol and character sets (HL-2150N / HL-2170W only) A For the HP LaserJet emulation modes, you can choose the symbol and character sets using Web Based Management (Web browser) when connected to a network or the control panel buttons. How to use Web Based Management (web browser) A To use Web Based Management (Web browser), follow the steps below. Note We recommend Microsoft Internet Explorer 6.0® (or greater) or Firefox® 1.0 (or greater) for Windows® and Safari™ 1.0 for Macintosh®.
Appendix Symbol and character sets list A OCR symbol sets A When you choose the OCR-A or OCR-B font, the matching symbol set is always used.
Appendix HP LaserJet mode PS Text (10J) Roman8 (8U) Roman9 (4U) Roman Extension (0E) Russian-GOST (12R) Symbol (19M) A 109
Appendix Quick reference for bar code control commands (HL-2150N / HL-2170W only) A The printer can print bar codes in the HP LaserJet emulation modes. Print bar codes or expanded characters Code ESC i Dec 27 105 Hex 1B 69 A Format: ESC i n ... n \ Creates bar codes or expanded characters according to the segment of parameters ‘n ... n’. For more information about parameters, see the following Definition of Parameters. This command must end with the ‘ \ ’ code (5CH).
Appendix This parameter selects the bar code mode as shown above. When n is ‘t5’ or ‘T5’ the bar code mode (EAN 8, EAN 13, or UPC A) varies according to the number of characters in the data. Bar code, expanded character, line block drawing and box drawing n = ‘s0’ or ‘S0’ 3: 1 (default) n = ‘s1’ or ‘S1’ 2: 1 n = ‘s3’ or ‘S3’ 2.5: 1 A This parameter chooses the bar code style as above.
Appendix Bar code human readable line ON or OFF n = ‘r0’ or ‘R0 Human readable line OFF n = ‘r1’ or ‘R1 Human readable line ON Preset: A Human readable line ON (1) ‘T5’ or ‘t5’ (2) ‘T6’ or ‘t6’ (3) ‘T130’ or ‘t130’ (4) ‘T131’ or ‘t131’ Preset: Human readable line OFF All others This parameter shows whether the printer prints the human readable line below the bar code.
Appendix Bar code & expanded character offset in Y-axis A n = ‘ynnn’ or ‘Ynnn’ This parameter shows the downward offset from the current print position in the ‘u’- or ‘U’-specified unit. Bar code, expanded character, line block drawing and box drawing height A n = ‘hnnn’, ‘Hnnn’, ‘dnnn’, or ‘Dnnn’ 1 EAN13, EAN8, UPC-A, ISBN (EAN13, EAN8, UPC-A), ISBN (UPC-E): 22 mm 2 UPC-E: 18 mm 3 Others: 12 mm Expanded characters i 2.
Appendix When Interleaved 2 of 5 is selected with the parameter ‘t1’ or ‘T1’: Ten numerical characters ‘0’ to ‘9’ can be accepted as bar code data. Other characters cause a data error. The number of characters for bar codes is not limited. This mode of bar codes needs even characters. If the bar code data has odd characters, ‘0’ is automatically added to the end of the bar code data.
Appendix When ISBN (UPC-E) is selected with the parameter ‘t131’ or ‘T131’: The same rules apply as for ‘t6’ or ‘T6’. When EAN 128 set A, set B or set C is selected with the parameter ‘t132’ or ‘T132’, ‘t133’ or ‘T133’ or ‘t134’ or ‘T134’ The same rules apply as for ‘t12’ or ‘T12’, ‘t13’ or ‘T13’, or ‘t14’ or ‘T14’. Box drawing A ESC i ... E (or e) ‘E’ or ‘e’ is a terminator. Line block drawing A ESC i ... V (or v) ‘V’ or ‘v’ is a terminator.
Appendix 'Codabar LPRINT CHR$(27);"it9r1s0o0x00y100bA123456A\"; 'Code 128 set A LPRINT CHR$(27);"it12r1o0x00y120bCODE128A12345?\"; 'Code 128 set B LPRINT CHR$(27);"it13r1o0x00y140bCODE128B12345?\"; 'Code 128 set C LPRINT CHR$(27);"it14r1o0x00y160b";CHR$(1);CHR$(2);"?\"; 'ISBN(EAN) LPRINTCHR$(27);"it130r1o0x00y180b123456789012?+12345\"; 'EAN 128 set A LPRINT CHR$(27);"it132r1o0x00y210b1234567890?\"; LPRINT CHR$(12) A END 116
B Appendix (for Europe and Other Countries) B Brother numbers B IMPORTANT For technical and operational help, you must call the country where you bought the printer. Calls must be made from within that country. Register your product B By registering your Brother product, you will be recorded as the original owner of the product.
Appendix (for Europe and Other Countries) Important information: regulations B Radio interference (220 to 240 volt model only) B This printer follows EN55022 (CISPR Publication 22)/Class B. International ENERGY STAR® Compliance Statement B The purpose of the International ENERGY STAR ® Program is to promote the development and popularization of energy-efficient office equipment. As an ENERGY STAR ® Partner, Brother Industries, Ltd.
Appendix (for Europe and Other Countries) For Finland and Sweden B LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT Varoitus! B Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. Varning B Om apparaten används på annat sätt än i denna Bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
Appendix (for Europe and Other Countries) IMPORTANT - for your safety B To ensure safe operation, the supplied three-pin plug must be inserted only into a standard three-pin power outlet that is properly grounded through the standard electrical wiring. Extension cords used with this printer must be three-pin plug type and correctly wired to provide grounding. Incorrectly wired extension cords may cause personal injury and equipment damage.
Appendix (for Europe and Other Countries) EC Declaration of Conformity B B 121
C Appendix (for USA and Canada) C Brother numbers C IMPORTANT For technical and operational help, you must call the country where you bought the printer. Calls must be made from within that country. Register your product C By registering your product with Brother International Corporation, you will be recorded as the original owner of the product.
Appendix (for USA and Canada) Customer Service In USA: 1-877-BROTHER (1-877-276-8437) In Canada: 1-877-BROTHER C If you have comments or suggestions, please write us at: In USA: Printer Customer Support Brother International Corporation 26250 Enterprise Ct. # 250 Lake Forest, CA 92630 In Canada: Brother International Corporation (Canada), Ltd. - Marketing Dept.
Appendix (for USA and Canada) Ordering supplies C For best quality results use only genuine Brother supplies, which are available at most Brother retailers. If you cannot find the supplies you need and you have a Visa, MasterCard, Discover, or American Express credit card, you can order supplies directly from Brother. (You can visit us online for a complete selection of the Brother accessories and supplies that are available for purchase.) Note In Canada, only Visa and MasterCard are accepted.
Appendix (for USA and Canada) Important information: regulations C Federal Communications Commission (FCC) Declaration of Conformity (USA only) Responsible Party: C Brother International Corporation 100 Somerset Corporate Boulevard P.O. Box 6911 Bridgewater, NJ 08807-0911 USA Telephone: (908) 704-1700 declares, that the products Product name: Laser Printer HL-2140, HL-2150N and HL-2170W Model number: HL-21 complies with Part 15 of the FCC Rules.
Appendix (for USA and Canada) International ENERGY STAR® Compliance Statement C The purpose of the International ENERGY STAR ® Program is to promote the development and popularization of energy-efficient office equipment. As an ENERGY STAR ® Partner, Brother Industries, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
Appendix (for USA and Canada) Laser notices C Laser safety (110 to 120 volt model only) C This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. This means that the printer does not produce hazardous laser radiation.
Appendix (for USA and Canada) IMPORTANT - for your safety C To ensure safe operation, the supplied three-pin plug must be inserted only into a standard three-pin power outlet that is properly grounded through the standard electrical wiring. Extension cords used with this printer must be three-pin plug type and correctly wired to provide proper grounding. Incorrectly wired extension cords may cause personal injury and equipment damage.
D Index A J Automatic Interface Selection ................................... 47 Job cancel ................................................................. 55 B L Bar code control ...................................................... 110 BRAdmin Light .......................................................... 46 BRAdmin Professional .............................................. 46 Brother Numbers (USA/Canada) ....................122, 123 LEDs ....................................................
Index S Scanner window ........................................................ 76 Service call ................................................................ 53 Service centers (USA/Canada) ............................... 123 Service centres (Europe and other countries) ........ 117 Software .................................................................... 46 Specifications ............................................................ 99 Status Monitor .................................................
