Service manual
Table Of Contents
- HL-2140/2150N/2170W SERVICE MANUAL
- PREFACE
- TABLE OF CONTENTS
- REGULATION
- SAFETY INFORMATION
- CHAPTER 1 TROUBLESHOOTING
- CHAPTER 2 PERIODICAL MAINTENANCE
- CHAPTER 3 DISASSEMBLY AND ASSEMBLY
- 1. SAFETY PRECAUTIONS
- 2. PACKING
- 3. SCREW TORQUE LIST
- 4. LUBRICATION
- 5. OVERVIEW OF GEARS
- 6. HARNESS ROUTING
- 7. DISASSEMBLY FLOW
- 8. DISASSEMBLY PROCEDURE
- 8.1 PAPER TRAY UNIT / SEPARATION PAD ASSY
- 8.2 FRONT COVER ASSY / SW KEY
- 8.3 BACK COVER / OUTER CHUTE ASSY
- 8.4 FUSER COVER ASSY
- 8.5 INNER CHUTE ASSY
- 8.6 FUSER UNIT
- 8.7 SIDE COVER R ASSY
- 8.8 CORNER COVER
- 8.9 SIDE COVER L ASSY
- 8.10 ROLLER HOLDER ASSY
- 8.11 WIRELESS LAN PCB ASSY (only HL-2170W)
- 8.12 MAIN SHIELD COVER PLATE
- 8.13 MAIN PCB ASSY
- 8.14 TOP COVER ASSY
- 8.15 SW SUPPORTER
- 8.16 PANEL PCB ASSY
- 8.17 HIGH-VOLTAGE PS PCB ASSY
- 8.18 NEW TONER SENSOR HARNESS ASSY
- 8.19 FILTER ASSY
- 8.20 LASER UNIT
- 8.21 FAN MOTOR 60 UNIT / COVER SENSOR HARNESS ASSY / TONER LED PCB ASSY
- 8.22 LVPS
- 8.23 REGISTRATION FRONT SENSOR PCB ASSY
- 8.24 REGISTRATION REAR SENSOR PCB ASSY
- 8.25 DRIVE SUB ASSY
- 8.26 DEV JOINT / DEV GEAR JOINT/53R / REGISTRATION PENDULUM GEAR SPRING
- 8.27 TONER SENSOR PCB UNIT ASSY
- 8.28 REGISTRATION SOLENOID / T1 SOLENOID
- 8.29 MAIN SHIELD PLATE / EJECT SENSOR PCB ASSY
- 8.30 RUBBER FOOT
- 8.31 MAIN FRAME L ASSY
- CHAPTER 4 ADJUSTMENTS AND UPDATING OF SETTINGS, REQUIRED AFTER PARTS REPLACEMENT
- CHAPTER 5 SERVICE SUPPORT SOFTWARE
- CHAPTER 6 CIRCUIT DIAGRAMS, WIRING DIAGRAM
- APPENDIX 1 SERIAL NUMBERING SYSTEM
- APPENDIX 2 SCREW CATALOGUE
- APPENDIX 3 DELETION OF PERSONAL INFORMATION
- APPENDIX 4 REFERENCES
- APPENDIX 5 GLOSSARY
1-26
Confidential
■ All black
Step Cause Check
Result
Remedy
1
Corona wire
failure
Are the electrodes on
the drum unit and
machine body dirty?
Ye s
Clean both electrodes.
2
Is the corona wire
damaged?
Ye s
Replace the drum unit.
3
Scanner harness
of the laser unit
connection
failure
Is the scanner harness
of the laser unit
connected securely?
No
Reconnect the scanner
harness of the laser unit.
4
FG harness
ASSY connection
failure
Is the FG harness ASSY
between the laser unit
and main PCB ASSY
connected securely?
No
Reconnect the FG harness
ASSY between the laser
unit and main PCB ASSY
securely.
5
HVPS PCB
failure
Is the problem solved
after replacing the
HVPS PCB ASSY?
Ye s
Replace the HVPS PCB
ASSY.
6
Main PCB failure Is the problem solved
after replacing the main
PCB ASSY?
Ye s
Replace the main PCB
ASSY.
7
Laser unit failure Is the problem solved
after replacing the laser
unit?
Ye s
Replace the laser unit.