Service manual
Table Of Contents
- HL-2140/2150N/2170W SERVICE MANUAL
- PREFACE
- TABLE OF CONTENTS
- REGULATION
- SAFETY INFORMATION
- CHAPTER 1 TROUBLESHOOTING
- CHAPTER 2 PERIODICAL MAINTENANCE
- CHAPTER 3 DISASSEMBLY AND ASSEMBLY
- 1. SAFETY PRECAUTIONS
- 2. PACKING
- 3. SCREW TORQUE LIST
- 4. LUBRICATION
- 5. OVERVIEW OF GEARS
- 6. HARNESS ROUTING
- 7. DISASSEMBLY FLOW
- 8. DISASSEMBLY PROCEDURE
- 8.1 PAPER TRAY UNIT / SEPARATION PAD ASSY
- 8.2 FRONT COVER ASSY / SW KEY
- 8.3 BACK COVER / OUTER CHUTE ASSY
- 8.4 FUSER COVER ASSY
- 8.5 INNER CHUTE ASSY
- 8.6 FUSER UNIT
- 8.7 SIDE COVER R ASSY
- 8.8 CORNER COVER
- 8.9 SIDE COVER L ASSY
- 8.10 ROLLER HOLDER ASSY
- 8.11 WIRELESS LAN PCB ASSY (only HL-2170W)
- 8.12 MAIN SHIELD COVER PLATE
- 8.13 MAIN PCB ASSY
- 8.14 TOP COVER ASSY
- 8.15 SW SUPPORTER
- 8.16 PANEL PCB ASSY
- 8.17 HIGH-VOLTAGE PS PCB ASSY
- 8.18 NEW TONER SENSOR HARNESS ASSY
- 8.19 FILTER ASSY
- 8.20 LASER UNIT
- 8.21 FAN MOTOR 60 UNIT / COVER SENSOR HARNESS ASSY / TONER LED PCB ASSY
- 8.22 LVPS
- 8.23 REGISTRATION FRONT SENSOR PCB ASSY
- 8.24 REGISTRATION REAR SENSOR PCB ASSY
- 8.25 DRIVE SUB ASSY
- 8.26 DEV JOINT / DEV GEAR JOINT/53R / REGISTRATION PENDULUM GEAR SPRING
- 8.27 TONER SENSOR PCB UNIT ASSY
- 8.28 REGISTRATION SOLENOID / T1 SOLENOID
- 8.29 MAIN SHIELD PLATE / EJECT SENSOR PCB ASSY
- 8.30 RUBBER FOOT
- 8.31 MAIN FRAME L ASSY
- CHAPTER 4 ADJUSTMENTS AND UPDATING OF SETTINGS, REQUIRED AFTER PARTS REPLACEMENT
- CHAPTER 5 SERVICE SUPPORT SOFTWARE
- CHAPTER 6 CIRCUIT DIAGRAMS, WIRING DIAGRAM
- APPENDIX 1 SERIAL NUMBERING SYSTEM
- APPENDIX 2 SCREW CATALOGUE
- APPENDIX 3 DELETION OF PERSONAL INFORMATION
- APPENDIX 4 REFERENCES
- APPENDIX 5 GLOSSARY

xi
Confidential
SAFETY INFORMATION
■ Caution for Laser Product (WARNHINWEIS fur Laser drucker)
CAUTION: When the machine during servicing is operated with the cover open, the
regulations of VBG 93 and the performance instructions for VBG 93 are
valid.
CAUTION: In case of any trouble with the laser unit, replace the laser unit itself. To
prevent direct exposure to the laser beam, do not try to open the enclosure
of the laser unit.
ACHTUNG: Im Falle von Störungen der Lasereinheit muß diese ersetzt werden. Das
Gehäuse der Lasereinheit darf nicht geöffnet werden, da sonst
Laserstrahlen austreten können.
<Location of the laser beam window>
■ Additional Information
When servicing the optical system of the machine, be careful not to place a screwdriver or
other reflective object in the path of the laser beam. Be sure to take off any personal
accessories such as watches and rings before working on the machine. A reflected beam,
though invisible, can permanently damage the eyes.
Since the beam is invisible, the following caution label is attached on the laser unit.