Service manual
Table Of Contents
- HL-2140/2150N/2170W SERVICE MANUAL
- PREFACE
- TABLE OF CONTENTS
- REGULATION
- SAFETY INFORMATION
- CHAPTER 1 TROUBLESHOOTING
- CHAPTER 2 PERIODICAL MAINTENANCE
- CHAPTER 3 DISASSEMBLY AND ASSEMBLY
- 1. SAFETY PRECAUTIONS
- 2. PACKING
- 3. SCREW TORQUE LIST
- 4. LUBRICATION
- 5. OVERVIEW OF GEARS
- 6. HARNESS ROUTING
- 7. DISASSEMBLY FLOW
- 8. DISASSEMBLY PROCEDURE
- 8.1 PAPER TRAY UNIT / SEPARATION PAD ASSY
- 8.2 FRONT COVER ASSY / SW KEY
- 8.3 BACK COVER / OUTER CHUTE ASSY
- 8.4 FUSER COVER ASSY
- 8.5 INNER CHUTE ASSY
- 8.6 FUSER UNIT
- 8.7 SIDE COVER R ASSY
- 8.8 CORNER COVER
- 8.9 SIDE COVER L ASSY
- 8.10 ROLLER HOLDER ASSY
- 8.11 WIRELESS LAN PCB ASSY (only HL-2170W)
- 8.12 MAIN SHIELD COVER PLATE
- 8.13 MAIN PCB ASSY
- 8.14 TOP COVER ASSY
- 8.15 SW SUPPORTER
- 8.16 PANEL PCB ASSY
- 8.17 HIGH-VOLTAGE PS PCB ASSY
- 8.18 NEW TONER SENSOR HARNESS ASSY
- 8.19 FILTER ASSY
- 8.20 LASER UNIT
- 8.21 FAN MOTOR 60 UNIT / COVER SENSOR HARNESS ASSY / TONER LED PCB ASSY
- 8.22 LVPS
- 8.23 REGISTRATION FRONT SENSOR PCB ASSY
- 8.24 REGISTRATION REAR SENSOR PCB ASSY
- 8.25 DRIVE SUB ASSY
- 8.26 DEV JOINT / DEV GEAR JOINT/53R / REGISTRATION PENDULUM GEAR SPRING
- 8.27 TONER SENSOR PCB UNIT ASSY
- 8.28 REGISTRATION SOLENOID / T1 SOLENOID
- 8.29 MAIN SHIELD PLATE / EJECT SENSOR PCB ASSY
- 8.30 RUBBER FOOT
- 8.31 MAIN FRAME L ASSY
- CHAPTER 4 ADJUSTMENTS AND UPDATING OF SETTINGS, REQUIRED AFTER PARTS REPLACEMENT
- CHAPTER 5 SERVICE SUPPORT SOFTWARE
- CHAPTER 6 CIRCUIT DIAGRAMS, WIRING DIAGRAM
- APPENDIX 1 SERIAL NUMBERING SYSTEM
- APPENDIX 2 SCREW CATALOGUE
- APPENDIX 3 DELETION OF PERSONAL INFORMATION
- APPENDIX 4 REFERENCES
- APPENDIX 5 GLOSSARY

x
Confidential
■ Industry Canada Compliance Statement (For Canada)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
■ Laser Safety (110 to 120 volt model only)
This machine is certified as a Class 1 laser product under the U.S. Department of Health
and Human Services (DHHS) Radiation Performance Standard according to the Radiation
Control for Health and Safety Act of 1968. This means that the machine does not produce
hazardous laser radiation.
Since radiation emitted inside the machine is completely confined within protective housings
and external covers, the laser beam cannot escape from the machine during any phase of
user operation.
■ FDA Regulations (110 to 120 volt model only)
The U.S. Food and Drug Administration (FDA) has implemented regulations for laser
products manufactured on and after August 2, 1976. Compliance is mandatory for products
marketed in the United States. The following label on the back of the machine indicates
compliance with the FDA regulations and must be attached to laser products marketed in the
United States.
■ Internal laser radiation
Maximum radiation power: 10 mW
Wave length: 780 - 800 nm
Laser class: Class 3B
MANUFACTURED:
Brother Technology (Shenzhen) Ltd.
NO6 Gold Garden Ind., Nanling Buji, Longgang, Shenzhen, China
This product complies with FDA performance standards for laser products except for
deviations pursuant to Laser Notice No.50, dated Jun 24, 2007.