User's Guide
BKH600 User Guide
09/06/2019
If the earbuds are not linking with each other, or not
working properly, try doing a factory reset by following
the steps below.
1. Place both earbuds inside the Charging Case and make
sure they are charging (the LED of both earbuds should
be solid WHITE).
2. While in the Charging Case, touch and HOLD the
multifunction touchpad of either earbud for 8 seconds
until the LED of that earbud flashes RED 3 times. This
will clear the pairing information.
Charging using the USB Type-C cable
Insert the USB Type-C cable into the USB port of the
charging case as shown below and connect the other
end to any USB Charger or charging device. The Charging
Case’s LED indicators will flash while charging and become
solid when fully charged.
See pages 12 and 13 for more details regarding the
charging case’s LED indicators.
Qi Charging
Wirelessly charge the case by placing it on any Qi wireless
Charging Pad (not included) as shown below.
Follow the steps below to pair and connect the earbuds
to your Bluetooth enabled device.
Connecting
1. The earbuds will automatically
be in Bluetooth pairing mode
when taken out of the case for
the first time.
2. After the earbuds link with each
other, the LED of the right earbud
will quickly flash RED while the
LED of the left earbud will slowly
flash WHITE indicating they are
in Bluetooth pairing mode.
3. Open your device’s Bluetooth
menu and find Brookstone
BKH600 and select it to pair.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modications to this unit not expressly approved
by the party responsible for compliance could void the user's authority
to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help
Information Regarding Exposure to Radio Frequency Energy
Your device is designed and manufactured not to exceed the emission
limits for exposure to RF energy set by the Federal Communications
Commission of the United States (FCC). Information on your Device is
on le with the FCC and can be found under the Display Grant section
of http://www.fcc.gov/oet/ea/ after searching on the FCC ID for your
Device, which can be found on the back of the Device.
LITHIUM POLYMER BATTERY WARNINGS
This device contains a non-removable Lithium-
Polymer battery. The battery must be recycled
or disposed of properly. Contact your local waste
management oce for information on battery
recycling or disposal.
Rating Label Denitions
Direct current symbol.
This symbol signies the product must not be discarded
as household waste, and should be delivered to an
appropriate collection facility for recycling. Proper disposal
and recycling helps protect natural resources, human
health and the environment.
This symbol signies and declares that this equipment
has battery charging which complies with California
CEC and energy eciency.
This symbol signies that this is a wireless device powered
by Bluetooth® technology. The Bluetooth® word mark
and logos are registered trademarks owned by Bluetooth
SIG, Inc., used under license.
1-Year Limited Warranty Territory: United States/Canada
LIMITED WARRANTY TO ORIGINAL CONSUMER
This product (including any accessories included in the original packaging) as supplied
and distributed new by an authorized retailer is warranted by Southern Telecom, Inc.
to the original consumer purchaser against defects in materials and workmanship
(“Warranty”) as follows:
To obtain warranty service:
• Visit our website at www.southerntelecom.com
• Click on Product Support
• Select the Brand of your device
• Select Service Request and fill out the form to begin your inquiry
Or call the Customer Support number below:
1-877-668-4839 (Toll Free)
Monday - Friday: 8AM - 10PM (EST)
Your product will be repaired or replaced, at our option, for the same or similar model
of equal value if examination by the service center determines this product is defective.
Products received damaged as a result of shipping will require you to file a claim with
the carrier.
Warranty service not provided
This warranty does not cover damage resulting from accident, misuse, abuse, improper
installation or operation, lack of reasonable care, unauthorized modification including
software modifications such as the installation of custom firmware. This warranty is
voided in the event any unauthorized person opens, alters or repairs this product.
All products being returned to the authorized service center for repair must be
suitably packaged.
NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, OTHER THAN THOSE EXPRESSLY DESCRIBED ABOVE SHALL APPLY. DISTRIBUTOR
The Ear Detection feature conveniently pauses the audio
playback when either earbud is taken out of your ear.
Just place the earbud back into your ear to resume the
audio playback.
The earbuds include a multifunction touchpad. Just
touch the earbuds to control the audio playback and
answer calls.
Multifunction Touchpad Operation
Play/Pause:
Double-tap the Left earbud.
Next track:
Double-tap the Right earbud.
Answer/End call:
Double-tap the Right or Left earbud
during an incoming call to answer, and
double-tap again during the call to
end it.
Rejecting a call:
Press and HOLD the Right or Left earbud during an
incoming call.
Voice Assistant:
Press and HOLD the Right or Left earbud. Press and
HOLD once again to cancel the Voice Assistant.
3. Repeat step 2 with the other earbud.
4. Take both earbuds out of the case, then put them back
into the case for 10 seconds.
5. Remove both earbuds from the Charging Case and let
them link with each other (this will occur automatically).
6. Once linked, they will automatically go into pairing
mode. The LED of the Right earbud will quickly flash
WHITE while the LED of the left earbud will slowly
flash WHITE.
7. Open your device’s Bluetooth list and delete Brookstone
BKH600 from your paired devices list.
8. Turn off the Bluetooth feature of your device and then
turn it back on and search for Brookstone BKH600
to connect.
IN THE BOX CHARGING BLUETOOTH PAIRINGPOWER ON/OFF EAR DETECTION
You can use the Right earbud alone to make or answer
calls while the Left earbud is in the case but the Left earbud
cannot be used alone while the Right earbud is in the case.
USING ONE EARBUD
TOUCH CONTROL LED INDICATORS FACTORY RESET
FCC INFORMATION LIMITED WARRANTY
TRUE WIRELESS EARBUDS
When you take out an earbud,
the music pauses
Qi Wireless Charging Pad
FURTHER DISCLAIMS ALL WARRANTIES AFTER THE EXPRESS WARRANTY PERIOD STATED
ABOVE. NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR
ENTITY WITH RESPECT TO THE PRODUCT SHALL BE BINDING ON DISTRIBUTOR. REPAIR,
REPLACEMENT, OR REFUND OF THE ORIGINAL PURCHASE PRICE - AT DISTRIBUTOR’S
SOLE DISCRETION - ARE THE EXCLUSIVE REMEDIES OF THE CONSUMER. IN NO EVENT
WILL DISTRIBUTOR OR ITS MANUFACTURERS BE LIABLE FOR ANY INCIDENTAL, DIRECT,
INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT
LIMITED TO, DAMAGES FOR LOSS OF PROFITS, BUSINESS, SAVINGS, DATA OR RECORDS)
CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE PRODUCT. EXCEPT AS STATED
HEREIN, NO OTHER WARRANTIES SHALL APPLY. NOTWITHSTANDING THE FOREGOING,
CONSUMER’S RECOVERY AGAINST DISTRIBUTOR SHALL NOT EXCEED THE PURCHASE
PRICE OF THE PRODUCT SOLD BY DISTRIBUTOR. THIS WARRANTY SHALL NOT EXTEND
TO ANYONE OTHER THAN THE ORIGINAL CONSUMER WHO PURCHASED THE PRODUCT
AND IS NOT TRANSFERABLE.
Some countries, states or provinces do not allow the exclusion or limitation of incidental
or consequential damages or allow limitations on warranties, so limitation or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have
other rights that vary from state to state or province to province. Contact your authorized
retailer to determine if another warranty applies.
The BROOKSTONE® trademarks, names and logos are owned by BKST Brand Holdings
LLC. ©2019 All rights reserved. www.brookstone.com
Manufactured, marketed and distributed by Southern Telecom Inc. under license.
Airphones is a registered trademark of Southern Telecom, Inc.
The "Qi" symbol is a trademark of the Wireless Power Consortium.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.
All other trademarks and trade names are those of their respective owners.
Made in China v1.0 08-2019
The earbuds and charging case include LED indicators
that are used to explain their different states.
4. Once paired, the voice prompt “Connected” will be
heard and the LEDs of both earbuds will slowly flash
WHITE.
Note: After taking the earbuds out of the case, they will
automatically link to each other and then try to connect
to a previously paired Bluetooth enabled device. If they
do not find a device to connect to, they will automatically
be in Bluetooth pairing mode.
Disconnecting
Open the Bluetooth settings on your device, and select
“Disconnect” to disconnect from an already connected
device. You'll hear a voice prompt "Disconnected" and
the earbuds will go into pairing mode.
Note: Do not select “Forget this device” or you will have
to go through the pairing process again.
The earbuds will automatically power
on when taken out of the charging
case and power off when placed back
into the charging case.
To manually power the earbuds ON
or OFF follow the instructions below:
Power ON:
Press and HOLD the Multifunctional
Touchpad on both earbuds for 2 seconds.
Power OFF:
Press and HOLD the Multifunctional
Touchpad of any earbud for 8 seconds.
Note: If not connected to a Bluetooth enabled device,
the earbuds will automatically power off after 3 minutes.
BKH600
Bluetooth Profiles:
A2DP V1.3, AVRCP V1.6
HFP V1.7, HSP V1.2
Charging Case (while charging)
Charging Case (not charging, when the cover is opened or closed) Earbuds (not in the Charging Case) Earbuds (in the Charging Case)
Charging Case
User GuideEarbud Tips
Charging Case
True Wireless Earbuds
USB Type-C cable
Ear Detection
Multifunction
Touchpad
LED Indicator
Charging
Connector
Microphone
TOP
USB Type-C port
LED Indicators
Multifunction
Touchpad
Wall outlet
USB Charger
(not included)
USB Type-C Cable
USB Type-C port
Charging Case
Battery Level LED
The first LED will slowly flash WHITE.
The first LED is solid WHITE while the
second LED is slowly flashing WHITE.
The first two LEDs are solid WHITE while
the third LED is slowly flashing WHITE.
All three LEDs are solid WHITE.
Battery Level LED
Less than 5%
5% – 30%
30% – 70%
More than 70%
The first LED will slowly flash WHITE
for 5 seconds.
The first LED is solid WHITE for 5
seconds, then it will turn off.
The first and second LEDs are solid
WHITE for 5 seconds, then they will
turn off.
All three LEDs are solid WHITE for 5
seconds, then they will turn off.
Multifunction
Touchpad
LED Indicator
TOP of the Earbud
Charging Case
Multifunction
Touchpad
Charging Case
LED IndicatorsCharging Case
USB Type-C Cable
Earbud Status LED
Low Battery Quickly flashes RED twice every minute.
The LED indicators of both earbuds are
slowly flashing WHITE.
Connected
The Right earbud LED is quickly flashing
RED and the Left earbud LED is slowly
flashing WHITE.
Bluetooth
Pairing
Charging Status LED
Charging
Fully Charged
Solid WHITE.
Solid WHITE for 1 minute and
then turns off.
R
Quickly flashSlowly flash
L
Earbud
Bluetooth menu
Brookstone BKH600
DEVICES
Bluetooth
i
Ear Detection
RL
Charging Case
LED Indicators
Brookstone BKH600
DEVICES
Bluetooth
i
Disconnect
Forget this device
<
Bluetooth
0% – 30%
30% – 70%
More than 70%
Fully charged
LED Indicators
TOP of the Charging Case
L R
TRUE WIRELESS EARBUDS
Correct
Wrong
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20 21