User's Manual
Table Of Contents
- 1 Identification
- 2 Declaration of Conformity
- 3 General Instructions
- 4 Safety Instructions
- 5 Product Specifications
- 6 Installation
- 7 Operation
- 7.1 Operating personnel
- 7.2 Protocol change
- 7.3 Operation of the ASC-I1 protocol
- 7.3.1 Structure of the communication protocol
- 7.3.2 Package contents
- 7.3.3 Commands of protocol
- Commands host to reader
- Commands reader to host
- Message items
- X - Read data
- W - Write data
- R - Automatic read
- G - Request parameter value
- P - Set parameter
- N - Reset
- e - Error message
- H - Heartbeat
- V - Query software version
- L - Lock a page of the transponder
- I - Set tuning of the RF module
- J - Request tuning settings of RF module
- A - Sensor event
- 7.3.4 Parameters
- 7.3.5 Message examples
- 7.4 Operation of SECS/HSMS Protocol
- 7.4.1 Introduction
- 7.4.2 SECS-I implementation
- 7.4.3 HSMS option
- 7.4.4 HSMS implementation
- 7.4.5 SECS-II implementation
- 7.4.6 Parameters
- Parameter 0 (0x00)
- Parameter 1 (0x01)
- Parameter 2 (0x02)
- Parameter 3 (0x03)
- Parameter 4 (0x04)
- Parameter 5 (0x05)
- Parameter 6 (0x06)
- Parameter 7 (0x07)
- Parameter 8 (0x08)
- Parameter 9 (0x09)
- Parameter 11 (0x0B)
- Parameter 12 (0x0C)
- Parameter 20 (0x14)
- Parameter 22 (0x16)
- Parameter 23 (0x17)
- Parameter 24 (0x18)
- Parameter 25 (0x19)
- Parameter 26 (0x1A)
- Parameter 27 (0x1B)
- Parameter 29 (0x1D)
- Parameter 30 (0x1E)
- Parameter 31 (0x1F)
- Parameter 32 (0x20)
- Parameter 33 (0x21)
- Parameter 34 (0x22)
- Parameter 35 (0x23)
- Parameter 36 (0x24)
- Parameter 37 (0x25)
- Parameter 38 (0x26)
- Parameter 40 (0x28)
- Parameter 41 (0x29)
- Parameter 42 (0x2A)
- Parameter 43 (0x2B)
- Parameter 44 (0x2C)
- Parameter 45 (0x2D)
- Parameter 98 (0x62)
- Parameter 99 (0x63)
- 7.4.7 SEMI E99
- 7.4.8 Message details
- 7.4.9 HSMS message examples
- 7.4.10 SECS-I message examples
- 8 Service and Troubleshooting
- 9 Dismantling and Storage
- 10 Transport and Disposal
- 11 Accessories
Product Manual - RFID Reader LF60C SoliD 99
Chapter 7
Operation
Parameter 9
(0x09)
Heartbeat time
The reader offers the option of generating a regular heartbeat. This means the
reader sends an S1F1 message to the host at the defined interval.
0 … No heartbeat
1 … 255 10 s (10 s - 2,550 s)
Default: 0 no heartbeat
Parameter 11
(0x0B)
ReaderID
The reader ID is a part of the device ID. In the message header, it corresponds to
the 7 LSB (last significant bits) of the "upper message ID".
00 .. 127
Default: 0x01
The BROOKS reader works simultaneously as a gateway and a reader (CIDRW
with integrated head). Therefore the reader ID is predefined as 0x01. Of course,
the ID can be changed within the valid scope.
Parameter 12
(0x0C)
HeadID
If you use a 2-byte TARGETID, this parameter corresponds to TARGETID.
00 .. 31
Default: 0x01
The head ID is predefined as 0x01. Of course, the ID can be changed within the
valid scope.
Parameter 20
(0x14)
Sensor delay for presence sensor
Delay time for sensor signal to start an automatic read.
0 .. 255 1/10 s
Default: (10) 1 s
Parameter 22
(0x16)
Sensor-triggered action for presence sensor
0: Read all transponders
1: Read page 1 of a multipage transponder
...
17: Read page 17 of a multipage transponder
240: Read a read/only transponder
241: Read a read/write transponder
Default: (0) read all transponders