User's Manual
Table Of Contents
- 1 Identification
- 2 Declaration of Conformity
- 3 General Instructions
- 4 Safety Instructions
- 5 Product Specifications
- 6 Installation
- 7 Operation
- 7.1 Operating personnel
- 7.2 Protocol change
- 7.3 Operation of the ASC-I1 protocol
- 7.3.1 Structure of the communication protocol
- 7.3.2 Package contents
- 7.3.3 Commands of protocol
- Commands host to reader
- Commands reader to host
- Message items
- X - Read data
- W - Write data
- R - Automatic read
- G - Request parameter value
- P - Set parameter
- N - Reset
- e - Error message
- H - Heartbeat
- V - Query software version
- L - Lock a page of the transponder
- I - Set tuning of the RF module
- J - Request tuning settings of RF module
- A - Sensor event
- 7.3.4 Parameters
- 7.3.5 Message examples
- 7.4 Operation of SECS/HSMS Protocol
- 7.4.1 Introduction
- 7.4.2 SECS-I implementation
- 7.4.3 HSMS option
- 7.4.4 HSMS implementation
- 7.4.5 SECS-II implementation
- 7.4.6 Parameters
- Parameter 0 (0x00)
- Parameter 1 (0x01)
- Parameter 2 (0x02)
- Parameter 3 (0x03)
- Parameter 4 (0x04)
- Parameter 5 (0x05)
- Parameter 6 (0x06)
- Parameter 7 (0x07)
- Parameter 8 (0x08)
- Parameter 9 (0x09)
- Parameter 11 (0x0B)
- Parameter 12 (0x0C)
- Parameter 20 (0x14)
- Parameter 22 (0x16)
- Parameter 23 (0x17)
- Parameter 24 (0x18)
- Parameter 25 (0x19)
- Parameter 26 (0x1A)
- Parameter 27 (0x1B)
- Parameter 29 (0x1D)
- Parameter 30 (0x1E)
- Parameter 31 (0x1F)
- Parameter 32 (0x20)
- Parameter 33 (0x21)
- Parameter 34 (0x22)
- Parameter 35 (0x23)
- Parameter 36 (0x24)
- Parameter 37 (0x25)
- Parameter 38 (0x26)
- Parameter 40 (0x28)
- Parameter 41 (0x29)
- Parameter 42 (0x2A)
- Parameter 43 (0x2B)
- Parameter 44 (0x2C)
- Parameter 45 (0x2D)
- Parameter 98 (0x62)
- Parameter 99 (0x63)
- 7.4.7 SEMI E99
- 7.4.8 Message details
- 7.4.9 HSMS message examples
- 7.4.10 SECS-I message examples
- 8 Service and Troubleshooting
- 9 Dismantling and Storage
- 10 Transport and Disposal
- 11 Accessories
Product Manual - RFID Reader LF60C SoliD 102
Chapter 7
Operation
Parameter 33
(0x21)
Automatic antenna adjustment
The parameter defines the permitted causes for an antenna adjustment.
0 Automatic adjustment is not activated
1 Automatic adjustment only by DIP8
2 Automatic adjustment only by external command
3 Automatic adjustment by DIP8 or external command
Default: (3) automatic antenna adjustment by DIP8 or external command
Parameter 34
(0x22)
Sensor type for presence sensor
Type of sensor signal to start an automatic read.
0 Automatic read starts if sensor is covered
1 Automatic read starts if sensor is not covered
Default: (0) sensor is covered
Parameter 35
(0x23)
Special features
After a hardware reset, the reader offers an automatic read if the presence sensor
is covered.
bit 0: value 0: Effect auto read after reset, if sensor is covered
value 1: Effect no auto read after reset, if sensor is coverd (default)
bit 1: value 0: Effect a sensor triggered auto read (default)
value 1: Effect no sensor triggerd auto read
bit 2: Without function
bit 3: Without function
bit 4: The setting of the LEDs by S18F13 "SetLED" is prioritized
Default: 0x01 (0000 0001)
Parameter 36
(0x24)
DIP switch activation
Bits 0 to bit 4 define the behavior of DIP switches 8 down to 5. DIP switches 4
down to 1 have no function at this time.
bit0: DIP 8 for tuning is active in test mode
bit1: DIP 8 for tuning is active in normal mode
bit2: DIP 7 (activate test mode) activation
bit3: DIP 6 (type of test mode) activation
bit4: DIP 5 can be used for protocol change
Default: 0x1F (0001 1111)