User's Manual
Table Of Contents
- 1 Identification
- 2 Declaration of Conformity
- 3 General Instructions
- 4 Safety Instructions
- 5 Product Specifications
- 6 Installation
- 7 Operation
- 7.1 Operating personnel
- 7.2 Protocol change
- 7.3 Operation of the ASC-I1 protocol
- 7.3.1 Structure of the communication protocol
- 7.3.2 Package contents
- 7.3.3 Commands of protocol
- Commands host to reader
- Commands reader to host
- Message items
- X - Read data
- W - Write data
- R - Automatic read
- G - Request parameter value
- P - Set parameter
- N - Reset
- e - Error message
- H - Heartbeat
- V - Query software version
- L - Lock a page of the transponder
- I - Set tuning of the RF module
- J - Request tuning settings of RF module
- A - Sensor event
- 7.3.4 Parameters
- 7.3.5 Message examples
- 7.4 Operation of SECS/HSMS Protocol
- 7.4.1 Introduction
- 7.4.2 SECS-I implementation
- 7.4.3 HSMS option
- 7.4.4 HSMS implementation
- 7.4.5 SECS-II implementation
- 7.4.6 Parameters
- Parameter 0 (0x00)
- Parameter 1 (0x01)
- Parameter 2 (0x02)
- Parameter 3 (0x03)
- Parameter 4 (0x04)
- Parameter 5 (0x05)
- Parameter 6 (0x06)
- Parameter 7 (0x07)
- Parameter 8 (0x08)
- Parameter 9 (0x09)
- Parameter 11 (0x0B)
- Parameter 12 (0x0C)
- Parameter 20 (0x14)
- Parameter 22 (0x16)
- Parameter 23 (0x17)
- Parameter 24 (0x18)
- Parameter 25 (0x19)
- Parameter 26 (0x1A)
- Parameter 27 (0x1B)
- Parameter 29 (0x1D)
- Parameter 30 (0x1E)
- Parameter 31 (0x1F)
- Parameter 32 (0x20)
- Parameter 33 (0x21)
- Parameter 34 (0x22)
- Parameter 35 (0x23)
- Parameter 36 (0x24)
- Parameter 37 (0x25)
- Parameter 38 (0x26)
- Parameter 40 (0x28)
- Parameter 41 (0x29)
- Parameter 42 (0x2A)
- Parameter 43 (0x2B)
- Parameter 44 (0x2C)
- Parameter 45 (0x2D)
- Parameter 98 (0x62)
- Parameter 99 (0x63)
- 7.4.7 SEMI E99
- 7.4.8 Message details
- 7.4.9 HSMS message examples
- 7.4.10 SECS-I message examples
- 8 Service and Troubleshooting
- 9 Dismantling and Storage
- 10 Transport and Disposal
- 11 Accessories
Product Manual - RFID Reader LF60C SoliD 101
Chapter 7
Operation
Parameter 29
(0x1D)
Transponder load duration (read mode)
The time required to load a transponder during a read process.
The default value (50 ms) should not be changed.
00 .. 255 ms
Default: (50) 50 ms
Parameter 30
(0x1E)
r/w synchronize
Enables/disables reader synchronization. If synchronization is enabled, the reader
takes notice of interference or other active readers and synchronizes the reading
cycle.
00 … Synchronization disabled
01 … Synchronization enabled
Default: (01) enabled
Parameter 31
(0x1F)
Auto-adjust value (read mode)
The influence of interferences in the environment of the readers can be minimized
by using the automatic adjustment during the operation. If the parameter is set
to defined values (0x00 - 0x08), the reader starts the adjustment.
In case of automatic adjustment, the reader requires up to two seconds. During
this time the reader cannot receive any serial data.
00 ... 0x07 Range of manual adjustment (read mode only)
0x08 Start automatic adjustment (read and write mode)
Parameter 32
(0x20)
Auto-adjust value (write mode)
The influence of interferences in the environment of the readers can be minimized
by using the automatic adjustment during the operation. If the parameter is set
to defined values (0x00 - 0x08), the reader starts the adjustment.
In the case of automatic adjustment, the reader requires up to two seconds.
During this time the reader cannot receive any serial data.
00 ... 0x07 Range of manual adjustment (write mode only)
0x08 Start automatic adjustment (read and write mode)
IMPORTANT
Automatic adjustment changes the adjustment of the read and write modes
(parameters 31 and 32).