TM ® SIMP HOME LIFE BY DESIG N TM DRAPER / BAXTER / TIERNEY FLOOR STORAGE CABINET MODEL # AXCBCDRP-01 1/18
TM ® SIMP HOME LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION A MODEL # AXCBCDRP-01 . . BL BR /onFrt ntaAv ntaAv /onFrt ntaAv /onFrt TOP QTY 1 . LEFT SIDE QTY 1 . C RIGHT SIDE QTY 1 . D E ntaAv /onFrt BOTTOM SHELF QTY 1 . MIDDLE SHELF QTY 1 . F . G1 G2 LEG (L&R Same) QTY 2 DOOR QTY 1 . SHELF QTY 1 LEG (L&R Same) QTY 2 . H I TOP BACK PANEL QTY 1 BOTTOM BACK PANEL QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION . MODEL # AXCBCDRP-01 HARDWARE DESCRIPTION 1 2 . CAM LOCK PIN CAM LOCK QTY 12 SETS . . 3 MAGNET AND PLATE QTY 1 SET ADJUSTABLE HINGE QTY 2 . 4 . 5 PHILLIPS SCREW M4 X 15mm QTY 16 SHELF SUPPORT QTY 4 . 6 . 7 . 8 . 9 ALLENKEYBOLTM : 6X50mmQ - TY8 LOCKWASHERØ : 10/Ø6X15.mmQ - TY8 WASHERØ : 16/Ø6X1mmQ - TY8 PHILLIPS SCREW ROUND HEAD M4 X 15mm QTY 2 PHILLIPS SCREW M3 X 15mm QTY 4 QTY 8 SETS ALLEN KEY QTY 1 . 10 11 a.M4X25mm-QTY2 (1siextra) b.M4X15mm-QTY1 c.
COMPONENTS-KEY DIAGRAM /onFrt MODEL # AXCBCDRP-01 A ntaAv H /onFrt /onFrt ntaAv D ntaAv BR BL E I /onFrt ntaAv C F G1 G2 G1 G2 7/18
ASSEMBLY MODEL # AXCBCDRP-01 STEP-1 9 8 G2 G1 G1 C G2 1. Attach Legs G1, G2 to Bottom C . 2. Use eight Allen Key Bolts 8 , eight Lock Washers 8 and eight Washers 8 to secure part C and G1 ,G2. 3. Use Allen Key 9 to tighten Bolts. Do not over-tighten P STEP-2 1 X 1 C 1 Avant For/nt 1. Attach Cam Lock Pins 1 into pre-drilled holes on part C . 2. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten.
ASSEMBLY MODEL # AXCBCDRP-01 P STEP-3 X 1 1 1 A Avant Fron/t 1 BR Avant Fron/t 6 1 BL 4 Avant Fron/t 1. Attach Cam Lock Pins 1 into pre-drilled holes on parts A , BL , BR . 2.AttachMagnet4usingPhilpsScrews6intopre-driledholesonLeftSideBL. 3. Use Phillips screwdriver to secure Cam Lock Pins and Screws. Do not over-tighten.
ASSEMBLY MODEL # AXCBCDRP-01 STEP-4 1 D D tnavA BL tnavA BL / ontrF / ontrF 1. Align Cam Lock Pins with guide holes on part D and attach part D to Left Side BL . 2. Insert two Cam Locks 1 into guide holes on part D . 3. Use Phillips screwdriver to secure Cam Locks. STEP-5 1 D D / ontrF tnavA tnavA BR tnavA tnavA BL / ontrF / ontrF BL / ontrF BR 1. Repeat Step-4 for the Right Side BR .
ASSEMBLY MODEL # AXCBCDRP-01 STEP-6 1 tnavA /ontrF tnavA /ontrF tnavA /ontrF tnavA /ontrF BL BR BR BL tnavA tnavA /ontrF /ontrF C C 1. Align Cam Lock Pins with guide holes on parts BL , BR and attach parts BL , BR to part C . 2. Insert two Cam Locks 1 into guide holes on each part BL , BR . 3. Use Phillips screwdriver to secure Cam Locks. H tnavA /ontrF BL I BR C 4.SlideBackPanelsH,Ifirmlyinto slotsonSidesBL,BRandBottomShelfC.
ASSEMBLY MODEL # AXCBCDRP-01 STEP-7 A tnavA /ontrF H tnavA /ontrF tnavA tnavA /ontrF /ontrF BL BR tnavA /ontrF tnavA /ontrF A BL BR 1 1. Align Cam Lock Pins with guide holes on parts BL , BR and attach part A to parts BL , BR . 2. Insert two Cam Locks 1 into guide holes on each part BL , BR . 3. Use Phillips screwdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCBCDRP-01 STEP-8 H 7 BR I BL 5 C 10 1. Attach the Back Panels H , I to back frame using Phillips Screws Round Head 7 through guide holes from Back Panels. 2. Attach the Corners Support 10 to back frame using Phillips Screws 5 through guide holes from Corners Support 10 . 3. Use Phillips Screwdriver to tighten screws. Do not over-tighten. STEP-9 4 E 1. Use four Shelf Supports 4 for Cabinet Shelf E in desired location .
ASSEMBLY MODEL # AXCBCDRP-01 STEP-10 3 6 F 5 2 1. Attach Adjustable Hinges 2 to Door F using Phillips Screws 5 into pre-drilled holes on Door F . 2.AttachMagnetPlate3totopcornerofDoorFusingPhilpsScrews6into pre-driledholesonDoorF. STEP-11 BR 2 F 5 1. Attach Adjustable Hinges 2 on Door F to Right Side BR using Phillips Screws 5 into pre-drilled holes on Right Side BR . 2. Use Phillips screwdriver to snugly tighten screws.
ASSEMBLY MODEL # AXCBCDRP-01 STEP-12 IMPORTANT NOTE: 5 II I Tighten the Screw marked II to fasten hinge. The door may need to be adjusted so that all the spaces between the door and the unit sides are equal. To adjust, follow instructions: 1. Side adjustment 4 mm To move the door towards the side panel, loosen screw I and tighten screw II . To move the door away from the side panel, loosen screw II and tighten screw I . 2.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-13 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. P x 3. 4. 5. 6. 7. Drill a 3/16 inch hole in the wall.
TM ® SIMP HOME LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.
