PLATINUM SMART-HEAT™ ELECTRIC HEATER SERIES II BY BROMIC INSTALLATION, INSTRUCTION AND SERVICE MANUAL AVAILABLE IN 2300W & 3400W VERSION ! IMPORTANT Original Instructions Version 3.2 AU READ THIS MANUAL CAREFULLY. SEE INSIDE COVER FOR IMPORTANT INFORMATION ABOUT THIS MANUAL. KEEP INSTRUCTION WITH APPLIANCE FOR FUTURE REFERENCE.
! IMPORTANT This manual contains important information about the installation, operation, and maintenance of Platinum Smart-Heat™ Electric Heaters. Please pay close attention to the important safety information shown throughout this instruction manual. Any safety information will be accompanied by the following safety alert symbols: ! DANGER, ! WARNING, ! IMPORTANT • READ THIS MANUAL CAREFULLY before installing or servicing this product.
CONTENTS IMPORTANT NOTES & WARNINGS 4 PRODUCT OVERVIEW 5 PRODUCT DESCRIPTION 5 SPECIFICATIONS 5 PRODUCT FEATURES 5 HEATER INSTALLATION INSTRUCTIONS 6 CEILING & WALL MOUNTING 6 CEILING RECESS 9 TUBE SUSPENSION 10 ELECTRICAL INSTALLATION 11 SERVICING 11 TROUBLESHOOTING 11 bromic.
IMPORTANT NOTES AND WARNINGS ! • IMPORTANT - Installation MUST be carried out by a licensed and authorised person. • • Improper installation, adjustment, or alteration and failure to follow the warnings and instructions in this manual could result in severe personal injury, death or property damage. Do not perform maintenance until heater has been turned off, power disconnected, and heater temperature has cooled to room temperature.
IMPORTANT NOTES AND WARNINGS CONTINUED ... or swimming pool. Any switches or controls must not be within reach of a person in the bathtub, shower or swimming pool. • To maintain Ingress Protection Rating (IPX4), only IP44 rated conduit fittings should be used for electrical installation. • This product does not have a switch for electrical disconnection. A means for disconnection of the heater must be incorporated in the fixed wiring according to the local electrical codes.
HEATING INSTALLATION INSTRUCTIONS CEILING & WALL MOUNTING • • Heaters must be away from the fourth wall. CEILING MOUNTING (FACE DOWN) WALL MOUNTING CEILING CEILING 165 150 CEILING CEILING MOUNTING (ANGLED) 245 Heaters must be installed according to the minimum installation clearances shown in these diagrams Minimum distance between heaters measured from edge of heater must be at least 500mm.
HEATING INSTALLATION INSTRUCTIONS CONTINUED... OPTION 1 To exit the cable through the side of the wall mounting bracket, start from step 1. e 1. Unscrew and remove plug-in wall bracket (a). b 2. Attach extra supplied cable gland into the same hole from the outside of the bracket. Fasten in place with the metal cable gland nut from inside the bracket (b).
9. Fit the smaller cover over the heater bracket so that the slots pass over the shafts of the M6x14mm mountingINSTRUCTIONS screws (i). Fit the larger cover over the HEATING INSTALLATION CONTINUED... smaller cover in the same way from the opposite side of the bracket (j). 8. To fix heater at desired angle, fully insert M3x10mm positioning screws (included with wall bracket) on Use angled covers if heater is angled.
HEATING INSTALLATION INSTRUCTIONS CONTINUED... CEILING RECESS (SOLD SEPARATELY) ! WARNING Instructions below are suitable for ceiling surfaces 10-30mm thick. For ceiling surfaces thicker than 30mm, contact Bromic for alternative installation options. ! WARNING The heater shall, under no circumstance, be covered with insulating material or similar material. ! ! WARNING ! WARNING In ceiling recess installation, the heater must be completely protected against water contact from above.
HEATING INSTALLATION INSTRUCTIONS CONTINUED... 1. Prepare ceiling cut-out with dimensions from images on P.9 to fit ceiling recess frame (a). Heater must be installed with heater surface at least 2400mm above the floor level, with 500mm clearance to the nearest wall on all sides of the heater. Minimum distances to combustibles within cavity must be according to only one of the two options shown. " 9.1 / 0 " 23 .1 9 0/ " 23 9.1 / 0 23 87 0/ 87 34.2 " 0/ 34 87 .2" 0/ 34 .2a " 2.
the 4 M5 screws and nuts provided (k). HEATING INSTALLATION INSTRUCTIONS CONTINUED... 12. Remove the 4 M5 screws fastening the heater mounting bracket to the back of the heater. Re-insert the screws with both halves of the ceiling support bracket in place and tighten firmly. (l) 13. Make electrical connection from heater to power supply. This is described under 'Electrical Installation' CEILING RECESS (SOLD SEPARATELY) k 11.
ELECTRICAL INSTALLATION ! WARNING ELECTRICAL INSTALLATION This heater MUST be permanently installed by an authorised/licenced person. Do not perform maintenance, or carry out installation or assembly procedure while electrical power is switched on. 1. 2. ! WARNING ELECTRICAL SHOCK HAZARD! Serious injury or death may occur. Disconnect from electrical supply before installing or servicing this heater. Read and follow installation clearance requirements outlined in this manual.
BRdM1c· HEATING 26. The manufacturer is not responsible for assuring compliance with jurisdictional codes and regulations governing sales, construction, installation and/or use of the heating products and cannot be responsible for how the product is installed or used.
