User Manual

BLOCK PART NUMBERS MAIN CAP PART NUMBERS SLEEVES
• 8B HS 3650: 3.650 X .4375 • 8B HS 4750: 4.750 X .4375 • 8B HS 5000: 5.000 X .4375 • 8B HS 5550: 5.550 X .4375 • 8B HS 6000: 6.000 X .4375 • 8B HS 6250 3/8: 6.250 X .4375 STEPPED TO .375 FOR -12 AND -18 • 8B HS 6300: 6.300 X .4375 • 8B HS 6600 3/8 H-11: 6.600 X .4375 STEPPED TO .375 FOR GB 2300 • AR 300-8303: 12 POINT 7/16 NUT • AR AJN 12-1: 3/8 12 POINT NUT • AR AJW 750: 3/8 WASHER • 8B MS HS WASHER: 7/16 HS WASHER
• 8B PLUG/BLOCK • 8B PLUG/-10 • 8B PLUG 814-6C: #6 AN ALUMINUM PLUG • 8B PLUG 814-7C: #7 AN ALUMINUM PLUG • 8B PPLUG ST 1/4: STEEL PIPE PLUG • 8B PPLUG AL 1/4: ALUMINUM PIPE PLUG • 8B PPLUG ST 3/8: STEEL PIPE PLUG • 8B PPLUG AL 3/8: ALUMINUM PIPE PLUG • 8B PPLUG ST 1/2: STEEL PIPE PLUG • 8B PPLUG AL 1/2: ALUMINUM PIPE PLUG • 8B 0-RING/-10 PLUG: O-RING FOR -10 PLUG • 8B O-RING/BLOCK PLUG
MAIN STUDS, NUTS, MAIN CAP BOLTS, AND WASHERS
CAM LOCATION AND SPECS
• STANDARD CAM LOCATION • RAISED CAM LOCATION -.391 • USE WIDE BEARING WITH 1/4” LOCKS IN CENTER BEARINGS AND SPIRAL LOCKS ON THE TWO END BEARINGS • AVAILABLE WITH BIG BLOCK CAM JOURNALS • REQUIRES SPECIAL CAM BEARINGS AVAILABLE FROM BRODIX • ROLLER CAM BEARINGS AVAILABLE UPON REQUEST • 50 mm CAM BEARINGS AVAILABLE UPON REQUEST • 55 mm CAM BEARINGS AVAILABLE UPON REQUEST • 8B 1200 SERIES .391 RAISED CAM ONLY ACCESSORIES • AVAILABLE WITH OR WITHOUT A FUEL PUMP • STANDARD BLOCK - STARTER BOSS ON RIGHT SIDE • NO STARTER PROVISION ON SPRINT CAR BLOCKS • HEAD STUDS AVAILABLE • PLUG KIT INCLUDED FOR BLOCKS MAIN CAPS • 350 OR 400 MAINS • BILLET STEEL MAIN CAPS STANDARD • ALIGN HONE AVAILABLE • ALL CAPS ARE WET SUMP - MUST BE PLUGGED FOR DRY SUMP USE
HEIGHTS OF BLOCKS
• 9.010 TO 9.510 • 9.010 TO 9.625, 8B 1200 SERIES STROKE CLEARANCE • STANDARD CAM LOCATION - 4.125 • RAISED CAM - 4.250 • RAISED CAM LOCATION HAS A WIDE PAN RAIL ONLY • 8B 1200 SERIES, UP TO 4.375 STANDARD, 4.500 WITH ADDITIONAL MACHINING
• 8B 1000*: 400 MAIN BLOCK, 4.125 BORE • 8B 1050*: 350 MAIN BLOCK, 4.125 BORE • 8B 1100*: 400 MAIN BLOCK, 4.000 BORE • 8B 1150*: 350 MAIN BLOCK, 4.000 BORE * PLEASE SPECIFY BELL HOUSING STYLE AND CAM LOCATION THAT IS DESIRED • 8B 1200 C: 400 MAIN BLOCK, 4.125 BORE STD BELL HOUSING • 8B 1200 D: 400 MAIN BLOCK, 4.125 BORE OPEN BELL HOUSING • 8B 1250 C: 350 MAIN BLOCK, 4.125 BORE STD BELL HOUSING • 8B 1250 D: 350 MAIN BLOCK, 4.125 BORE OPEN BELL HOUSING • 350 ST-L: 350 ALL STEEL, LIGHTENED • 400 ST-L: 400 ALL STEEL, LIGHTENED • 350 AL/ST-L: 350 ALUMINUM FRONT AND REAR, STEEL CENTERS, LIGHTENED • 400 AL/ST-L: 400 ALUMINUM FRONT AND REAR, STEEL CENTERS, LIGHTENED • 350 TI: 350 TITANIUM FRONT AND CENTERS, ALUMINUM OR STEEL REAR • 400 TI: 400 TITANIUM FRONT AND CENTERS, ALUMINUM OR STEEL REAR • 8B MS 4500: 7/16 X 4.500 LONG • 8B MS 4100: 7/16 X 4.100 LONG • 8B MS/HS: WASHER FOR MAIN STUD • 8B MS 12 PT NUT: 7/16 NUT • 8B BOLT/12 PT 3/8: 12 POINT 3/8 BOLT • 8B WASHER 3/8 H: 3/8 AN HARDENED WASHER • 8B SL 100-1010: 350 THICK WALL REPAIR SLEEVE ONLY • 8B SL 100-1011: THICK WALL REPAIR SLEEVE ONLY • 8B SL 100-1011 TD: 400 THICK WALL REPAIR SLEEVE ONLY FOR TALL DECK • 8B SL 43-075: STANDARD 400 WALL SLEEVE • 8B SL 43-075 A: STANDARD 350 WALL SLEEVE • 8B SL 43-075 TD: STANDARD 400 WALL SLEEVE FOR TALL DECK • 8B SL 43-075 TD 5: STANDARD 400 WALL SLEEVE FOR 9.500 TALL DECK • 8B SL 41-535 4.170 ID, 4.365 OD STD DECK SLEEVE FOR 8B 1200 SERIES BLOCKS • 8B SL 41-600 4.170 ID, 4.365 OD TALL DECK SLEEVE FOR 8B 1200 SERIES BLOCKS
HEAD STUDS
PLUGS AND O-RINGS
• 8B DOW/PULL: DOWEL FOR MAIN CAPS • 8B DOW/RING: RING DOWEL FOR MAIN CAPS • 8B DOW/TC HEAD: TIMING COVER HEAD DOWEL • 8B DOW/TC FRONT: TIMING COVER DOWEL • 8B DOW/BH 1.25: BELL HOUSING DOWEL 1.25 LONG • 8B DOW/BH 1.50: BELL HOUSING DOWEL 1.50 LONG DOWELS • 8B BOLT/CAM-LOCK: LOCK FOR CAM BEARING • 8B RCAM PLUG BB: BIG BLOCK CAM PLUG • 8B RCAM PLUG BB SPRINT: BIG BLOCK CAM PLUG FOR SPRINT • 8B RCAM PLUG 55: 55 mm CAM PLUG • 8B RCAM PLUG SPRINT: CAM PLUG FOR SPRINT • 8B RCAM PLUG STD: CAM PLUG FOR STD BLOCK • 8B O-RING/RCAM PLUG: O-RING FOR REAR CAM PLUG • 8B ORING/RCAM PLUG BB: O-RING FOR BB CAM PLUG • 8B ORING/RCAM PLUG 55: O-RING FOR 55 mm CAM PLUG • 8B RCAM-SNAP RING: REAR CAM SNAP RING • 8B RCAM BB RING: REAR CAM SNAP RING FOR BB CAM • 8B SPIRAL LOCK: SPIRAL RETAINING RING • 8B SPIRAL LOCK BB: SPIRAL RETAINING RING FOR BB CAM • 8B SPIRAL LOCK 55: SPIRAL RETAINING RING FOR 55 mm • 8B SPIRAL LOCK RB: SPIRAL RETAINING RING FOR ROLLER BEARING • 8B RCAM SEAL: REAR CAM SEAL FOR SPRINT CAM PLUGS
www.brodix.com • 301 MAPLE AVENUE • P.O. BOX 1347 • MENA, AR 71953
ORDER, TECH, AND INFORMATION: [phone] • FAX: [phone]
BRODIX® has been the innovative
leader in cylinder head quality and technology for the past 40 years. The BRODIX® block is no exception and is made from the highest quality virgin A-356 aluminum. The main webs have been reinforced to withstand all types of racing. This block is offered in several versions.
• 4.000 OR 4.125 BORE WITH MAX BORE 4.155 • STANDARD: 4.2725 o.d. X 5.540 o.a.l. • 9.300 TALL DECK: 4.2725 X 5.740 o.a.l. • 9.500 TALL DECK: 4.2725 o.d. X 6.040 o.a.l. • REPAIR SLEEVES AVAILABLE • 8B 1200 SERIES, 4.180 MIN BORE, 4.250 MAX BORE • 9.000 TALL DECK: 4.365 o.d. X 5.535 o.a.l. • 9.600 TALL DECK: 4.365 o.d. X 6.000 o.a.l.
SLEEVES TORQUE SPECS
• OUTSIDE MAIN: 65 ft-lb TORQUE WITH LIGHT OIL • INSIDE MAIN: 75 ft-lb • FRONT AND REAR MAIN: 3/8 12 POINT 30 ft-lb • HEAD TORQUE: 70 ft-lb
OILING SYSTEM • PRIMARY OILING SYSTEM • WHEN USING RAISED CAM BLOCK, OIL PUMP SHAFT MUST BE MODIFIED OR SPACER MUST BE INSTALLED UNDER WET SUMP OIL PUMP. (.350 THICK) • REMOTE OIL FILTER ONLY
Not legal for sale or use on pollution controlled motor vehicles. © Copyright 2010 Brodix, Inc.
Replacement Part Numbers
Not legal for sale or use on pollution controlled motor vehicles. © Copyright 2010 Brodix, Inc.
www.brodix.com • 301 MAPLE AVENUE • P.O. BOX 1347 • MENA, AR 71953
ORDER, TECH, AND INFORMATION: [phone] • FAX: [phone]
PRIMARY OIL SYSTEM
BRODIX® SMALL BLOCK
350 / 400 WET SUMP
OIL PASSAGE MAP