Owner's manual

Standby Management CPU [Slot-10]:
SW: Version 07.4.00T3e3 Copyright (c) 1996-2012 Brocade Communications Systems,
Inc. All rights reserved.
Compiled on Mar 02 2012 at 11:54:29 labeled as SXR07400
BootROM: Version 07.2.00T3e5 (FEv2)
HW: Chassis FastIron SX 800-PREM6 (PROM-TYPE SX-FIL3U-6-IPV6)
==========================================================================
SL 1: SX-FI-8XG 8-port 10G Fiber
Serial #: BQKxxxxxxxx
P-ASIC 0: type C341, rev 00 subrev 00
==========================================================================
SL 2: SX-FI-24GPP 24-port Gig Copper + PoE+
Serial #: BTUxxxxxxxx
P-ASIC 2: type C300, rev 00 subrev 00
==========================================================================
SL 8: SX-FI-48GPP 48-port Gig Copper + PoE+
Serial #: BFVxxxxxxxx
P-ASIC 14: type C300, rev 00 subrev 00
==========================================================================
SL 9: SX-FIZMR6 0-port Management
Serial #: Wxxxxxxxxx
License: SX_V6_HW_ROUTER_IPv6_SOFT_PACKAGE (LID: yGFJGOiFLd)
==========================================================================
SL 10: SX-FIZMR6 0-port Management
Serial #: Wxxxxxxxxx
License: SX_V6_HW_ROUTER_IPv6_SOFT_PACKAGE (LID: ÿÿÿÿÿÿÿÿÿÿ)
==========================================================================
Active Management Module:
660 MHz Power PC processor 8541 (version 0020/0020) 66 MHz bus
512 KB boot flash memory
16384 KB code flash memory
512 MB DRAM
Standby Management Module:
660 MHz Power PC processor 8541 (version 0020/0020) 66 MHz bus
512 KB boot flash memory
16384 KB code flash memory
512 MB DRAM
The system uptime is 1 minutes 2 seconds
The system : started=warm start reloaded=by "reload"
The version information is shown in bold type in this example:
• "03.1.00aT3e3" indicates the flash code version number. The "T3e3" is used by Brocade for record
keeping.
• "labeled as SXR03100a" indicates the flash code image label. The label indicates the image type
and version and is especially useful if you change the image file name.
• "Primary SXR03100a.bin" indicates the flash code image file name that was loaded.
Displaying the boot image version running on the device
To determine the boot image running on a device, enter the show flash command at any level of the
CLI. The following shows an example output.
device#show flash
Active Management Module (Slot 9):
Compressed Pri Code size = 3613675, Version 03.1.00aT3e3 (sxr03100a.bin)
Compressed Sec Code size = 2250218, Version 03.1.00aT3e1 (sxs03100a.bin)
Compressed BootROM Code size = 524288, Version 03.0.01T3e5
Code Flash Free Space = 9699328
Standby Management Module (Slot 10):
Compressed Pri Code size = 3613675, Version 03.1.00aT3e3 (sxr03100a.bin)
Compressed Sec Code size = 2250218, Version 03.1.00aT3e1 (sxs03100a.bin)
Compressed BootROM Code size = 524288, Version 03.0.01T3e5
Code Flash Free Space = 524288
The boot code version is shown in bold type.
Displaying the boot image version running on the device
90 FastIron Ethernet Switch Administration Guide
53-1003075-02