Owner's manual

Feature ICX 6430 ICX 6450 FCX ICX 6610 ICX 6650 FSX 800
FSX 1600
ICX 7750
10/100/1000 port speed 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Auto-negotiation 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Auto-negotiation maximum port speed
advertisement and down-shift
08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Duplex mode 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Auto MDI/MDIX detection 08.0.01 08.0.01 08.0.01 08.0.01 No 08.0.01 08.0.10
Port status (enable or disable) 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Flow control: Responds to flow control
packets, but does not generate them
08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Symmetric flow control: Can transmit
and receive 802.3x PAUSE frames
08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Auto-negotiation and advertisement of
flow control
08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 008.0.10
PHY FIFO Rx and TX Depth 08.0.01 08.0.01 08.0.01 08.0.01 No No No
Interpacket Gap (IPG) adjustment 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
CLI support for 100BaseTX and
100BaseFX
08.0.01
2
08.0.01
3
08.0.01 08.0.01 No 08.0.01 No
Gbps fiber negotiate mode No No 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
QoS priority 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
VoIP auto-configuration and CDP 08.0.01 08.0.01 08.0.01 08.0.01 No 08.0.01 08.0.10
Port flap dampening 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Port loop detection 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.01 08.0.10
Basic system parameter configuration
Brocade devices are configured at the factory with default parameters that allow you to begin using the
basic features of the system immediately. However, many of the advanced features such as VLANs or
routing protocols for the device must first be enabled at the system (global) level before they can be
configured. If you use the Command Line Interface (CLI) to configure system parameters, you can find
these system level parameters at the Global CONFIG level of the CLI.
NOTE
Before assigning or modifying any router parameters, you must assign the IP subnet (interface)
addresses for each port.
2
For 100BaseTX. ICX 6430-C supports 100BaseFX.
3
For 100BaseTX.
Basic system parameter configuration
30 FastIron Ethernet Switch Administration Guide
53-1003075-02