Manualshelf

Technical data

ManualsBrandsBrocade Communications Systems ManualsHome Theater ServerServerIron ADX 12.4.00a
121122123124125126127128129130
120 ServerIron ADX Advanced Server Load Balancing Guide
53-1002435-03
High availability designs with TCS
2
NOTE
This example shows commands that are valid on the ServerIron ADX device only when it is running
the Layer 3 router image.
NetIron(config)# vlan 1 name DEFAULT-VLAN by port
NetIron(config-vlan-1)# router-interface ve 1
NetIron(config-vlan-1)# exit
NetIron(config)# vlan 2 by port
NetIron(config-vlan-2)# untagged ethe 1 to 2
NetIron(config-vlan-2)# router-interface ve 2
NetIron(config-vlan-2)# exit
NetIron(config)# vlan 23 by port
NetIron(config-vlan-23)# untagged ethe 23
NetIron(config-vlan-23)# exit
NetIron(config)# interface ve 1
NetIron(config-ve-1)# ip address 172.1.1.4 255.255.255.0
NetIron(config-ve-1)# ip ospf area 0
NetIron(config-ve-1)# ip vrrp-extended vrid 3
NetIron(config-ve-1-vrid-3)# backup
NetIron(config-ve-1-vrid-3)# ip-address 172.1.1.1
NetIron(config-ve-1-vrid-3)# track-port e 1
NetIron(config-ve-1-vrid-3)# track-port e 2
NetIron(config-ve-1-vrid-3)# track-port e 8
NetIron(config-ve-1-vrid-3)# enable
NetIron(config-ve-1)# ip vrrp-extended vrid 4
NetIron(config-ve-1-vrid-4)# backup
NetIron(config-ve-1-vrid-4)# ip-address 172.1.1.2
NetIron(config-ve-1-vrid-4)# track-port e 1
NetIron(config-ve-1-vrid-4)# track-port e 2
NetIron(config-ve-1-vrid-4)# track-port e 8
NetIron(config-ve-1-vrid-4)# enable
NetIron(config-ve-1)# exit
NetIron(config)# interface ve 2
NetIron(config-ve-2)# ip address 10.2.24.2 255.255.255.0
NetIron(config-ve-2)# ip ospf area 0
NetIron(config-ve-2)# exit
NetIron(config)# interface ethernet 23
NetIron(config-if-23)# ip address 173.1.1.1 255.255.255.0
NetIron(config-if-23)# exit
NetIron(config)# ip route 0.0.0.0 0.0.0.0 10.2.24.251
NetIron(config)# ip router-id 10.2.24.2
NetIron(config)# router vrrp-extended
NetIron(config)# route-only
NetIron(config)# router ospf
NetIron(config-ospf-router)# area 0
NetIron(config-ospf-router)# redistribution connected
NetIron(config-ospf-router)# redistribution static
NetIron(config-ospf-router)# exit
Commands for ServerIron ADX 253
The following commands configure ServerIron ADX 253 in Figure 29.
NOTE
This example shows commands that are valid on the ServerIron ADX device only when it is running
the Layer 3 router image.