Home Theater Server User Manual
Table Of Contents
- Contents
- About This Document
- Network Security
- TCP SYN attacks
- IP TCP syn-proxy
- Granular application of syn-proxy feature
- Syn-def
- No response to non-SYN first packet of a TCP flow
- Prioritizing management traffic
- Peak BP utilization with TRAP
- Transaction Rate Limit (TRL)
- Understanding transaction rate limit
- Configuring transaction rate limit
- Configuring the maximum number of rules
- Saving a TRL configuration
- Transaction rate limit command reference
- Global TRL
- TRL plus security ACL-ID
- security acl-id
- Transaction rate limit hold-down value
- Displaying TRL rules statistics
- Displaying TRL rules in a policy
- Displaying IP address with held down traffic
- Refusing new connections from a specified IP address
- HTTP TRL
- Overview of HTTP TRL
- Configuring HTTP TRL
- Displaying HTTP TRL
- Display all HTTP TRL policies
- Display HTTP TRL policy from index
- Display HTTP TRL policy client
- Display HTTP TRL policy starting from index
- Display HTTP TRL policy matching a regular expression
- Display HTTP TRL policy client index (MP)
- Display HTTP TRL policy client index (BP)
- Display HTTP TRL policy for all client entries (BP)
- Downloading an HTTP TRL policy through TFTP
- HTTP TRL policy commands
- Logging for DoS Attacks
- Maximum connections
- clear statistics dos-attack
- Maximum concurrent connection limit per client
- Firewall load balancing enhancements
- Syn-cookie threshhold trap
- Service port attack protection in hardware
- Traffic segmentation
- DNS attack protection
- Access Control List
- How ServerIron processes ACLs
- Default ACL action
- Types of IP ACLs
- ACL IDs and entries
- ACL entries and the Layer 4 CAM
- Configuring numbered and named ACLs
- Modifying ACLs
- Displaying a list of ACL entries
- Applying an ACLs to interfaces
- ACL logging
- Dropping all fragments that exactly match a flow-based ACL
- Enabling ACL filtering of fragmented packets
- Enabling hardware filtering for packets denied by flow-based ACLs
- Enabling strict TCP or UDP mode for flow-based ACLs
- ACLs and ICMP
- Using ACLs and NAT on the same interface (flow-based ACLs)
- Displaying ACL bindings
- Troubleshooting rule-based ACLs
- IPv6 Access Control Lists
- Network Address Translation
- Syn-Proxy and DoS Protection
- Understanding Syn-Proxy
- Configuring Syn-Proxy
- DDoS protection
- Configuring a security filter
- Configuring a Generic Rule
- Configuring a rule for common attack types
- Configuring a rule for ip-option attack types
- Configuring a rule for icmp-type options
- Configuring a rule for IPv6 ICMP types
- Configuring a rule for IPv6 ext header types
- Binding the filter to an interface
- Clearing DOS attack statistics
- Clearing all DDOS Filter & Attack Counters
- Logging for DoS attacks
- Displaying security filter statistics
- Address-sweep and port-scan logging
- Secure Socket Layer (SSL) Acceleration
- SSL overview
- SSL acceleration on the ServerIron ADX
- Configuring SSL on a ServerIron ADX
- Basic SSL profile configuration
- Advanced SSL profile configuration
- Configuring Real and Virtual Servers for SSL Termination and Proxy Mode
- Configuration Examples for SSL Termination and Proxy Modes
- SSL debug and troubleshooting commands
- Displaying socket information
ServerIron ADX Security Guide 19
53-1002440-03
Configuring HTTP TRL
1
Syntax: [no] http-trl-policy <policy-name>
2. Configure an HTTP TRL client maximum connection.
ServerIronADX(config-http-trl-p1)# client-name c1 max-conn 10
Syntax: [no] client-name <client-name> max-conn <max-conn-value>
<max-conn-value>—specifies maximum number of connection client can setup.
3. Configure the action to take if a client exceeds the configured maximum connections
(optional).
ServerIronADX(config-http-trl-p1)# client-name c1 exceed-action reset
Syntax: [no] client-name <client-name> exceed-action reset
Configuring HTTP TRL defaults
Use the following procedures to configure the HTTP TRL default rate limit and the default maximum
connection.
Configuring HTTP TRL default rate limit
To configure HTTP TRL default rate limit, follow these steps.
1. Define an HTTP TRL policy.
ServerIronADX(config)# http-trl-policy p1
Syntax: [no] http-trl-policy <policy-name>
2. Configure an HTTP TRL default rate limit.
ServerIronADX(config-http-trl-p1)# default monitor-interval 1 10 20 0
Syntax: [no] default monitor-interval <interval-value> <warning-rate> <shutdown-rate>
<holddown-interval>
3. Configure the action to take if a client exceeds the configured rate limit (optional).
ServerIronADX(config-http-trl-p1)# default exceed-action reset
Syntax: [no] default exceed-action reset
Configuring HTTP TRL default maximum connection
To configure HTTP TRL default maximum connection, follow these steps.
1. Define an HTTP TRL policy.
ServerIronADX(config)# http-trl-policy p1
Syntax: [no] http-trl-policy <policy-name>
2. Configure an HTTP TRL default maximum connection.
ServerIronADX(config-http-trl-p1)# default max-conn 10
Syntax: [no] default max-conn <max-conn-value>
3. Configure the action to take if a client exceeds the configured maximum connection (optional).
ServerIronADX(config-http-trl-p1)# default exceed-action reset