Home Theater Server User Manual
Table Of Contents
- Contents
- About This Document
- Network Security
- TCP SYN attacks
- IP TCP syn-proxy
- Granular application of syn-proxy feature
- Syn-def
- No response to non-SYN first packet of a TCP flow
- Prioritizing management traffic
- Peak BP utilization with TRAP
- Transaction Rate Limit (TRL)
- Understanding transaction rate limit
- Configuring transaction rate limit
- Configuring the maximum number of rules
- Saving a TRL configuration
- Transaction rate limit command reference
- Global TRL
- TRL plus security ACL-ID
- security acl-id
- Transaction rate limit hold-down value
- Displaying TRL rules statistics
- Displaying TRL rules in a policy
- Displaying IP address with held down traffic
- Refusing new connections from a specified IP address
- HTTP TRL
- Overview of HTTP TRL
- Configuring HTTP TRL
- Displaying HTTP TRL
- Display all HTTP TRL policies
- Display HTTP TRL policy from index
- Display HTTP TRL policy client
- Display HTTP TRL policy starting from index
- Display HTTP TRL policy matching a regular expression
- Display HTTP TRL policy client index (MP)
- Display HTTP TRL policy client index (BP)
- Display HTTP TRL policy for all client entries (BP)
- Downloading an HTTP TRL policy through TFTP
- HTTP TRL policy commands
- Logging for DoS Attacks
- Maximum connections
- clear statistics dos-attack
- Maximum concurrent connection limit per client
- Firewall load balancing enhancements
- Syn-cookie threshhold trap
- Service port attack protection in hardware
- Traffic segmentation
- DNS attack protection
- Access Control List
- How ServerIron processes ACLs
- Default ACL action
- Types of IP ACLs
- ACL IDs and entries
- ACL entries and the Layer 4 CAM
- Configuring numbered and named ACLs
- Modifying ACLs
- Displaying a list of ACL entries
- Applying an ACLs to interfaces
- ACL logging
- Dropping all fragments that exactly match a flow-based ACL
- Enabling ACL filtering of fragmented packets
- Enabling hardware filtering for packets denied by flow-based ACLs
- Enabling strict TCP or UDP mode for flow-based ACLs
- ACLs and ICMP
- Using ACLs and NAT on the same interface (flow-based ACLs)
- Displaying ACL bindings
- Troubleshooting rule-based ACLs
- IPv6 Access Control Lists
- Network Address Translation
- Syn-Proxy and DoS Protection
- Understanding Syn-Proxy
- Configuring Syn-Proxy
- DDoS protection
- Configuring a security filter
- Configuring a Generic Rule
- Configuring a rule for common attack types
- Configuring a rule for ip-option attack types
- Configuring a rule for icmp-type options
- Configuring a rule for IPv6 ICMP types
- Configuring a rule for IPv6 ext header types
- Binding the filter to an interface
- Clearing DOS attack statistics
- Clearing all DDOS Filter & Attack Counters
- Logging for DoS attacks
- Displaying security filter statistics
- Address-sweep and port-scan logging
- Secure Socket Layer (SSL) Acceleration
- SSL overview
- SSL acceleration on the ServerIron ADX
- Configuring SSL on a ServerIron ADX
- Basic SSL profile configuration
- Advanced SSL profile configuration
- Configuring Real and Virtual Servers for SSL Termination and Proxy Mode
- Configuration Examples for SSL Termination and Proxy Modes
- SSL debug and troubleshooting commands
- Displaying socket information
104 ServerIron ADX Security Guide
53-1002440-03
Translation timeouts
4
ServerIronADX(config)# nat-forward-no-session
Syntax: [no] nat-forward-no-session
Translation timeouts
The NAT translation table contains all the currently active NAT translation entries on the device. An
active entry is one the ServerIron ADX creates for a private address when the client at that address
sends traffic.
NAT performs the following steps to provide an address translation for a source IP address:
• NAT looks in the translation table for an active NAT entry for the translation. If the table
contains an active entry for the session, the ServerIron ADX uses that entry.
• If NAT does not find an active entry in the NAT translation table, NAT creates an entry and
places the entry in the table. The entry remains in the table until the entry times out.
Each NAT entry remains in the translation table until the entry ages out.
After the configuration of a NAT timeout the following occurs:
• Existing entries of the modified protocol remain in the translation table.
• If existing session entries send or receive packets then the timeout value is updated to the new
configured value.
• If existing session entries do not process any traffic they will continue to age out in accordance
with the old timeout value.
• When the timeout (age of the session) expires, forward and reverse sessions in the ServerIron
ADX are deleted with no further actions. If traffic is received on this flow the ServerIron ADX
drops the packets because it will not find sessions related to that particular flow.
Configuring the NAT translation aging timer
Use the ip nat translation command to alter the NAT translation aging timer.
The NAT translation table contains all the currently active NAT translation entries on the device. An
active entry is one that the ServerIron ADX created for a private address when that client at that
address sent traffic to the Internet. NAT performs the following steps to provide an address
translation for a source IP address:
• The feature looks in the NAT translation table for an active NAT entry for the translation. If the
table contains an active entry for the session, the ServerIron ADX uses that entry.
• If NAT does not find an active entry in the NAT translation table, NAT creates an entry and
places the entry in the table. The entry remains in the table until the entry times out.
ServerIronADX(config)# ip nat translation tcp-timeout 1800
Syntax: [no] ip nat translation dns-timeout | finrst-timeout | icmp-timeout | syn-timeout |
tcp-timeout | udp-timeout <secs> maximum
Syntax: [no] ip nat translation max-entries <number-of-entries>
The dns-timeout keyword indicates connections to a Domain Name Server (DNS). The default is
120 seconds.