Home Theater Server User Manual
Table Of Contents
- Contents
- About This Document
- Network Security
- TCP SYN attacks
- IP TCP syn-proxy
- Granular application of syn-proxy feature
- Syn-def
- No response to non-SYN first packet of a TCP flow
- Prioritizing management traffic
- Peak BP utilization with TRAP
- Transaction Rate Limit (TRL)
- Understanding transaction rate limit
- Configuring transaction rate limit
- Configuring the maximum number of rules
- Saving a TRL configuration
- Transaction rate limit command reference
- Global TRL
- TRL plus security ACL-ID
- security acl-id
- Transaction rate limit hold-down value
- Displaying TRL rules statistics
- Displaying TRL rules in a policy
- Displaying IP address with held down traffic
- Refusing new connections from a specified IP address
- HTTP TRL
- Overview of HTTP TRL
- Configuring HTTP TRL
- Displaying HTTP TRL
- Display all HTTP TRL policies
- Display HTTP TRL policy from index
- Display HTTP TRL policy client
- Display HTTP TRL policy starting from index
- Display HTTP TRL policy matching a regular expression
- Display HTTP TRL policy client index (MP)
- Display HTTP TRL policy client index (BP)
- Display HTTP TRL policy for all client entries (BP)
- Downloading an HTTP TRL policy through TFTP
- HTTP TRL policy commands
- Logging for DoS Attacks
- Maximum connections
- clear statistics dos-attack
- Maximum concurrent connection limit per client
- Firewall load balancing enhancements
- Syn-cookie threshhold trap
- Service port attack protection in hardware
- Traffic segmentation
- DNS attack protection
- Access Control List
- How ServerIron processes ACLs
- Default ACL action
- Types of IP ACLs
- ACL IDs and entries
- ACL entries and the Layer 4 CAM
- Configuring numbered and named ACLs
- Modifying ACLs
- Displaying a list of ACL entries
- Applying an ACLs to interfaces
- ACL logging
- Dropping all fragments that exactly match a flow-based ACL
- Enabling ACL filtering of fragmented packets
- Enabling hardware filtering for packets denied by flow-based ACLs
- Enabling strict TCP or UDP mode for flow-based ACLs
- ACLs and ICMP
- Using ACLs and NAT on the same interface (flow-based ACLs)
- Displaying ACL bindings
- Troubleshooting rule-based ACLs
- IPv6 Access Control Lists
- Network Address Translation
- Syn-Proxy and DoS Protection
- Understanding Syn-Proxy
- Configuring Syn-Proxy
- DDoS protection
- Configuring a security filter
- Configuring a Generic Rule
- Configuring a rule for common attack types
- Configuring a rule for ip-option attack types
- Configuring a rule for icmp-type options
- Configuring a rule for IPv6 ICMP types
- Configuring a rule for IPv6 ext header types
- Binding the filter to an interface
- Clearing DOS attack statistics
- Clearing all DDOS Filter & Attack Counters
- Logging for DoS attacks
- Displaying security filter statistics
- Address-sweep and port-scan logging
- Secure Socket Layer (SSL) Acceleration
- SSL overview
- SSL acceleration on the ServerIron ADX
- Configuring SSL on a ServerIron ADX
- Basic SSL profile configuration
- Advanced SSL profile configuration
- Configuring Real and Virtual Servers for SSL Termination and Proxy Mode
- Configuration Examples for SSL Termination and Proxy Modes
- SSL debug and troubleshooting commands
- Displaying socket information
ServerIron ADX Security Guide 89
53-1002440-03
IACL overview
3
• If you want to tightly control access, configure ACLs consisting of permit entries for the access
you want to permit. The ACLs implicitly deny all other access.
• If you want to secure access in environments with many users, you might want to configure
ACLs that consist of explicit deny entries, then add an entry to permit all access to the end of
each ACL. The permit entry permits packets that are not denied by the deny entries.
Every IPv6 ACL has the following implicit condition as its last match conditions:
deny ipv6 any any – Denies IPv6 traffic. You must enter a permit ipv6 any any as the last
statement in the access-list if you want to permit IPv6 traffic that were not denied by the
previous statements.
NOTE
If an IPv6 ACL has the implicit deny condition, make sure it also permits the IPv6 link-local address,
in addition to the global unicast address. Otherwise, routing protocols such as OSPF will not work.
To view the link-local address, use the show ipv6 interface command.
The conditions are applied in the order shown above, with deny ipv6 any any as the last condition
applied.
For example, if you want to deny ICMP neighbor discovery acknowledgement, then permit any
remaining IPv6 traffic, enter commands such as the following:
The first permit statement permits ICMP traffic from hosts in the 2000:2383:e0bb::x network to
hosts in the 2001:3782::x network.
The deny statement denies ICMP neighbor discovery acknowledgement.
The last entry permits all packets that are not explicitly denied by the other entries. Without this
entry, the ACL will deny all incoming IPv6 traffic on the ports to which you assigned the ACL.
Furthermore, if you add the statement deny icmp any any in the access list, then all neighbor
discovery messages will be denied. You must explicitly enter the permit icmp any any nd-na and
permit icmp any any nd-ns statements just before the deny icmp statement if you want the ACLs to
permit neighbor discovery as in the example below.
ACL Syntax
NOTES: The following features are not supported:
• ipv6-operator flow-label
• ipv6-operator fragments when any protocol is specified. The option "fragments" can be
specified only when "permit/deny ipv6" is specified. If you specify "tcp" or any other protocol
instead of "ipv6" the keyword, "fragments" cannot be used.
• ipv6-operator routing when any protocol is specified. (Same limitation as for ipv6-operator
fragments)
ServerIronADX(config)# ipv6 access-list netw
ServerIronADX(config-ipv6-access-list-netw)# permit icmp 2000:2383:e0bb:
:/64 2001:3782::/64
ServerIronADX(config-ipv6-access-list-netw)# permit ipv6 any any
ServerIronADX(config)# ipv6 access-list netw
ServerIronADX(config-ipv6-access-list-netw)# permit icmp 2000:2383:e0bb:
:/64 2001:3782::/64
ServerIronADX(config-ipv6-access-list-netw)# deny icmp any any
ServerIronADX(config-ipv6-access-list-netw)# permit ipv6 any any