Installation guide

iv Brocade FastIron LS and FastIron LS-STK Hardware Installation Guide
53-1002187-01
DRAFT: BROCADE CONFIDENTIAL
Installing a redundant power supply . . . . . . . . . . . . . . . . . . . . . . . . . 17
About the RPS2-EIF redundant power supply . . . . . . . . . . . . . . 17
Installing a redundant power supply . . . . . . . . . . . . . . . . . . . . . . . . .19
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Selecting a site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Connecting devices to the redundant power supply . . . . . . . . .22
Ports pin-out (RPS2-EIF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installing an optional module in the device . . . . . . . . . . . . . . . . . . .25
Installing an SFP transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Powering on the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Verifying proper operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Attaching a PC or terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Wiring map for serial cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Chapter 3 Stacking EEPROM and Memory Upgrade for FastIron LS Series
Devices
Upgrade kit contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Upgrading hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Upgrading software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Chapter 4 Connecting Network Devices and Checking Connectivity
Assigning permanent passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Recovering from a lost password . . . . . . . . . . . . . . . . . . . . . . . .38
Configuring IP addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Devices running layer 2 software . . . . . . . . . . . . . . . . . . . . . . . .39
Devices running base layer 3 software . . . . . . . . . . . . . . . . . . .40
Assigning an IP address to an Ethernet port . . . . . . . . . . . . . . .40
Connecting network devices . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Cable specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Connecting to Ethernet or fast Ethernet hubs . . . . . . . . . . . . . .42
Connecting to workstations, servers, or routers . . . . . . . . . . . .43
Connecting a network device to a fiber port . . . . . . . . . . . . . . .44
Testing connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Observing LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Troubleshooting network connections. . . . . . . . . . . . . . . . . . . . . . . .46
Chapter 5 Maintaining the FLS and FLS-STK Hardware
Managing FastIron LS temperature settings. . . . . . . . . . . . . . . . . . .49
Using the temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . .49
Displaying the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Changing the temperature warning and shutdown levels . . . . 51
Changing the device temperature polling interval. . . . . . . . . . .52