Network Router User Manual
Table Of Contents
- About This Document
- Introduction
- Common Commands
- In this chapter
- Common commands
- show
- autoinstall
- banner
- commands
- crypto
- environment
- history
- interfaces
- ip
- ldap
- licenses
- logging
- mac
- mac-address-table
- management
- mobility
- ntp
- port-channel
- power
- privilege
- radius
- redundancy dynamic-ap-load-balance
- redundancy group
- redundancy history
- redundancy members
- rtls
- smtp-notification
- snmp
- snmp-server
- spanning-tree
- static-channel-group
- terminal
- timezone
- traffic-shape
- users
- version
- wireless
- (config-wireless) Executable Mode
- wlan-acl
- access-list
- aclstats
- alarm-log
- boot
- clock
- debugging
- dhcp
- file
- ftp
- password-encryption
- running-config
- securitymgr
- sessions
- startup-config
- upgrade-status
- mac-name
- firewall
- role
- virtual-IP
- wwan
- aap-wlan-acl
- aap-wlan-acl-stats
- protocol-list
- service-list
- User Exec Commands
- Privileged Exec Commands
- Global Configuration Commands
- In this chapter
- Global Configuration commands
- aaa
- access-list
- autoinstall
- banner
- boot
- bridge
- country-code
- crypto
- do
- end
- errdisable
- ftp
- hostname
- interface
- ip
- license
- line
- local
- logging
- mac
- mac-address-table
- mac-name
- management
- ntp
- prompt
- radius-server
- ratelimit
- redundancy
- role
- rtls
- service
- smtp-notification
- snmp-server
- spanning-tree
- timezone
- traffic-shape
- username
- vpn
- wireless
- wlan-acl
- network-element-id
- firewall
- virtual-ip
- wwan
- aap-wlan-acl
- arp
- power
- aap-ipfilter-list
- whitelist
- Crypto-isakmp Instance
- Crypto-group Instance
- Crypto-peer Instance
- Crypto-ipsec Instance
- Crypto-map Instance
- Crypto-trustpoint Instance
- Interface Instance
- Spanning tree-mst Instance
- Extended ACL Instance
- Standard ACL Instance
- Extended MAC ACL Instance
- DHCP Server Instance
- DHCP Class Instance
- Radius Server Instance
- Wireless Instance
- In this chapter
- Wireless configuration commands
- aap
- admission-control
- adopt-unconf-radio
- adoption-pref-id
- ap
- ap-containment
- ap-detection
- ap-image
- ap-ip
- ap-standby-attempts-threshold
- ap-timeout
- ap-udp-port
- auto-select-channels
- broadcast-tx-speed
- client
- clrscr
- cluster-master-support
- convert-ap
- country-code
- debug
- dhcp-one-portal-forward
- dhcp-sniff-state
- dot11-shared-key-auth
- end
- exit
- fix-broadcast-dhcp-rsp
- help
- hotspot
- load-balance
- mac-auth-local
- manual-wlan-mapping
- wireless-client
- mobility
- multicast-packet-limit
- multicast-throttle-watermark
- nas-id
- nas-port-id
- no
- proxy-arp
- qos-mapping
- radio
- rate-limit
- secure-wispe-default-secret
- self-heal
- sensor
- service
- show
- smart-rf
- smart-scan-channels
- wlan
- wlan-bw-allocation
- dot11k
- wips
- non-preferred-ap-attempts-threshold
- test
- RTLS Instance
- ESPI Instance
- RFID Instance
- SOLE Instance
- Smart RF Instance
- Role Instance
- AAP IP Filtering

298 Brocade Mobility RFS4000, RFS6000 and RFS7000 CLI Reference Guide
53-1001931-01
Global Configuration commands
5
• min-packets <1-65535> – Minimum packets
required for sending the trap
• <1-65535> – Defines the minimum packets for
sending the trap. This can be set with a decimal
number in the range of <1-65535>
• wireless-client [avg-bit-speed-less-than|
avg-retry-greater-than|avg-signal-less-than|
gave-up-percent-greater-than|
nu-percent-greater-than|pktsps-greater-than|
tput-greater-than|
undecrypt-percent-greater-than] – Modifies
wireless-client rate traps
• avg-bit-speed-less-than – Average bit speed in
Mbps is between <0.00> and <54.00>
• avg-retry-greater-than – Average retry is greater
than 0.00 and less than or equal to 16.00
• avg-signal-less-than – Average signal in dBm is
less than -0.00 and greater than or equal to
-120.00
• gave-up-percent-greater-than – Percentage of
pkts dropped is greater than 0.00 and less than
or equal to 100.00
• nu-percent-greater-than – Percentage of
non-unicast pkts is greater than 0.00 and less
than or equal to 100.00
• pktsps-greater-than – Packets per sec is greater
than 0.00 and less than or equal to 100000.00
• tput-greater-than – Throughput in Mbps is
greater than 0.00 and less than or equal to
100000.00
• undecrypt-percent-greater-than – Percentage of
undecryptable pkts is greater than 0.00 and
less than or equal to 100.00
engineid [netsnmp {<word>}|
text <word>]
Sets the SNMP server engine ID.
• netsnmp <word>– Sets the engine id to a
hexadecimal string
• text <word> – Sets the engine id to a text string
host <IP> [v2c|v3] {<1-65535>} SNMP server host.
• <IP> – SNMP server host IP address
• v2c <1-65535> – Use snmp version 2c
• v3 <1-65535> – Use snmp version 3
location <location-text> Text for mib object sysLocation.
manager [all|v2|v3] Enables the SNMP manager.
• all – Enables SNMP version v2 and v3
• v2 – Enables SNMP version v2
• v3 – Enables SNMP version v3
periodic-heartbeat-interval
<interval>
Sets periodic heartbeat trap interval. A periodic trap is
sent if no other traps are sent by the controller. The
default time period is 60 seconds. Set a value to between
10 and 1000 seconds.