Installation Guide

Page 4
MODELS QTXE080FLT • QTXE110FLT • QTXE150FLT
22
22
SERVICE PARTS
99043849A
Key No. Part No. Description
1 97016466 Housing
2 97016450 Duct Connector-6"
3 98010102 Wiring Plate
4 99170245 Screw, #8-18 X .375 (2 req’d)
5 97016933 Wire Panel/Harness Assembly
6 99020284 Blower Wheel
7 99080562 Motor (QTXE080FLT)
99080580 Motor (QTXE110FLT)
99080565 Motor (QTXE150FLT)
8 99100491 Isolator (4 req’d)
9 97016901 Motor Plate
10 99250959 Washer #8 (4 req’d)
11 99260558 Nut, Hex Lock #8-32 (4 req’d)
* 97016925 Blower Assembly (QTXE080FLT)
* 97016906 Blower Assembly (QTXE110FLT)
* 97016926 Blower Assembly (QTXE150FLT) (includes key nos. 6 thru 14)
12 99500397 Insulation (QTXE150FLT only)
13 99420648 Threaded Stud (QTXE150FLT only) (4 req’d)
14 99260570 Plastic Nut (QTXE150FLT only) (4 req’d)
15 97016864 Ballast Assembly
16 99260423 Nut, Hex #8-32 (2 req’d)
17 97016866 Grille Assembly (includes key nos. 18 & 20)
18 99140199 Grille Spring (2 req’d)
19 97016888 Bulb, 42W Fluorescent
20 99111284 Lens
21 99111293 Spacer (2 supplied)
22 QTHB1 Hanger Bar Kit
TAB
Order service parts by “Part No.” - not by “Key No.”
INSTALL GRILLE
5. Finish ceiling.
Install ceiling material. Cut out around housing.
6. Attach grille
to housing.
Squeeze grille
springs and insert
them into slots on
each side of
housing.
8. Remove
light lens.
Carefully insert a
small flat-blade
screwdriver
between grille and
lens. Pry lens out.
7. Push grille
against ceil-
ing.
9. Install light
bulbs.
Insert fluorescent
bulb* (supplied)
into its socket.
Purchase a 4W
incandescent
night-light bulb
and screw it into
its socket.
Replace lens.
* Use only one of the following 42W fluorescent lamps:
G.E. F42TBX827A4P/EOL or F42TBX830A4P/EOL
PHILIPS PL-T 42W/827/4P/ALTO or PL-T 42W/830/4P/ALTO
SYLVANIA CF42DT/E/IN/827 or CF42DT/E/IN/830
NEMA Type CFTR42W/GX24q/827 or CFTR42W/GX24q/830
Broan 97016888
SERVICE NOTE To
remove Blower Assembly:
Unplug motor (7).
Remove screw (4) from
motor plate (9) flange.
Find the single TA B on
the motor plate (located
next to the receptacle).
Push up near motor plate
tab while pushing out on
side of housing. Or insert
a straight-blade
screwdriver into slot in
housing (next to tab) and
twist screwdriver.
Replacement parts can
be ordered on our
website. Please visit us
at www.broan.com