INSTALLATION INSTRUCTIONS HB0072 E64000LC SERIES ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 13 & 14. Venmar Ventilation ULC, Drummondville, Québec www.broan.ca 877-896-1119 REGISTER YOUR PRODUCT ONLINE AT: www.broan.ca 21242 rev.
! WARNING ! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner.
- E64000LC SERIES RANGE HOOD SYSTEM INTERNAL BLOWERS MODEL 441 (10" ROUND WALL CAP) MODEL 437 (HIGH CAPACITY ROOF CAP) MODEL 647 (7" ROUND WALL CAP) MODEL 634 OR 644 (ROOF CAP) MODEL 415 (7" ROUND ADJUSTABLE ELBOW) MODEL 418 (10" ROUND ADJUSTABLE ELBOW) MODEL 412 TRANSITION (3¼" X 10" TO 7") MODEL 410 (10" ROUND DUCT — 2 FT. SECTIONS) MODEL 427 (4½" X 18½" TO 10" ROUND, 6" HIGH - LATERAL) 8" ROUND ADJUSTABLE ELBOW MODEL 407 (7" ROUND - 2 FT.
- E64000LC SERIES RANGE HOOD SYSTEM IN-LINE AND EXTERIOR BLOWERS MODEL 437 (HIGH CAPACITY ROOF CAP) MODEL HLB9 (800 CFM) OR HLB11 (1100 CFM) IN-LINE BLOWER (INCLUDES TWO 8" X 12" TO 10" ROUND TRANSITIONS) MODEL 331H (600 CFM) OR 332H (900 CFM) EXTERIOR BLOWER MODEL 335 (1200 CFM) OR 336 (1500 CFM) EXTERIOR BLOWER MODEL 441 (10" ROUND WALL CAP) MODEL 643 (8" ROUND WALL CAP) MODEL HLB6 (660 CFM) IN-LINE BLOWER (INCLUDES TWO 4½" X 18½" TO 10" ROUND TRANSITIONS) MODEL 421 (10" ROUND VERT.
1. SELECT BLOWER OPTION The Broan Elite E64000LC Series range hood includes many configurations: hoods with single or double internal blowers (included with the hoods), or hoods using external blowers. For hoods using external blowers, the Broan Elite E64000LC Series must be installed with in-line blower models HLB3, HLB6, HLB9 or HLB11, or exterior blower model 331H, 332H, 335 or 336 only. Other blowers cannot be substituted. (Blowers sold separately). Plan where and how the ductwork will be installed.
2. PREPARE THE INSTALLATION ! WARNING When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer.
2. PREPARE THE INSTALLATION (CONT’D) Cut-out the openings for duct (A) and power cable (B), in cabinet or wall, according to the direction of discharge chosen. See figures below. NOTE: For all internal blower hoods, the cut-out opening for house wiring can be made in cabinet bottom OR wall, no matter the discharge chosen (vertical or horizontal).
4. REMOVE THE FILTERS AND THE GREASE DRIP RAIL NOTE: For 36” and 42” wide double blower hoods, the adapter is taped on top of the filters. Remove adapter and set aside before removing filters. A. Remove tape on filters. Remove filters from hood and set aside. 1 NOTE: It is recommended to start with the middle filter(s). B. Lift out grease drip rail (1) and set aside. HD0584 A B 5.
6. CHOSE THE OPENING(S) (INTERNAL BLOWER HOODS ONLY) Remove the knockout for the chosen opening(s) (horizontal at the back of the hood or vertical on top). See illustrations below. VERTICAL DISCHARGE 1 2 3 HORIZONTAL DISCHARGE 1 2 3 HR0021 A B Punch out the appropriate electrical knockout hole on top (A) or back (B) of the hood. Install the wire clamp (included in parts bag). HR0024 7.
7. HORIZONTAL DISCHARGE INSTALLATION (INTERNAL BLOWER(S) ONLY) (CONT'D) Slide the blower to disengage its flange from the retaining bracket. HD0270 Flip the blower and engage its flange in the back wall retaining bracket. Using a 5/16" socket and the screws previously removed, secure the blower to the hood. RIGHT SIDE MOUNTING SCREW LOCATION LEFT SIDE MOUNTING SCREW LOCATION HD0271 HD0272 Plug the blower in. NOTE FOR DUAL BLOWER HOOD ONLY: Cut off the plastic tie wrap on left motor cable. HE0085 8.
9. INSTALL THE HOOD (ALL BLOWERS) INTERNAL BLOWER: Run power cable to installation location. Remove wiring cover and place the hood in its location. Mark the position of the screws (smaller part of the key holes [A]) with a pen. Remove the hood and install the four 1/2" double thread screws at marked positions, leaving a 1/8" gap. You may use up to eight key holes and screws for wider hoods and double blower hoods.
. LED LIGHTING The lighting of this hood is produced by two LED modules (included). ! WARNING Do not touch lamps during or soon after operation. Burns may occur. Cannot be replaced by any other type of light bulb or LED module. 13. REINSTALL GREASE DRIP RAIL AND BAFFLE FILTERS CAUTION Remove protective plastic film covering filters before installing them. Reinstall grease drip rail. The illustration at right shows how to reinsert the grease drip rail into the range hood.
14. USE AND CARE Baffle Filters The baffle filters should be cleaned frequently. Use a warm detergent solution. Wash often if your cooking style generates a lot of grease— like frying food or wok cooking. Remove baffle filters by pushing them towards the back of the hood and rotating them downward. Baffle filters are dishwasher safe. Allow filters to dry completely before reinstalling them in the hood. You may clean all-metal filters in the dishwasher using a non-phosphate detergent.
15. OPERATION (CONT'D) 1) LED lighting knob 2) Blower operation indicator 3) ON/OFF blower switch 4) Blower speed control knob 3 4 2 1 HC0073 A A) LED lighting knob B) Blower speed control knob B HC0035 COOKTOP LIGHTING The LED lighting of this hood is controled by a rotary dimmer switch (1). The lighting turns on at high intensity, and decreases as the knob is turned clockwise.
17.
18. SERVICE PARTS Broan Elite E64000LC Series Internal blower hoods Broan Elite E64000LC Series Exterior or In-Line blower hoods 1 15 15 14 14 13 2 2 17 12 3 11 4 18 10 3 11 12 13 16 4 10 5 6 6 7 7 8 HL0239 HL0238 KEY NO.
