Datasheet

ManualsBrandsBROADCOM ManualsLEDs & AccessoriesLED wired Yellow Rectangular 2 x 5 mm 4 mcd 110 ° 20 mA 2.1 V

HLMP-S100, HLMP-S201, HLMP-S301,

HLMP-S400, HLMP-S401, HLMP-S501, HLMP-S600

Package Dimensions

Features

• Rectangular light emitting surface

• Excellent for flush mounting on panels

• Choice of five bright colors

• Long life: solid state reliability

• Excellent uniformity of light output

Description

The HLMP-S100, -S201, -5301, -S400, -S401, -S501,

-S600 are epoxy encapsulated lamps in rectangular

packages which are easily stacked in arrays or used

for discrete front panel indicators. Contrast and

light uniformity are enhanced by a special epoxy

diffusion and tinting process.

The HLMP-S100 uses double heterojunction (DH)

absorbing substrate (AS) aluminum gallium arsenide

(AlGaAs) LEDs to produce outstanding light output

over a wide range of drive currents.

2.41 (0.100)

2.03 (0.085)

2.23 (0.088)

1.98 (0.078)

8.00 (0.315)

7.37 (0.290)

25.40 (1.00) MIN.

CATHODE LEAD

BOTTOM VIEW

SIDE VIEW

1.27 (0.50)

NOMINAL

NOTES:

1. ALL DIMENSIONS ARE IN

MILLIMETERS (INCHES).

2. AN EPOXY MENISCUS MAY EXTEND

ABOUT 1 mm (0.040") DOWN THE LEADS.

3. THERE IS A MXIMUM 1° TAPER FROM

BASE TO THE TOP OF LAMP.

2.54 (0.100)

NOMINAL

0.46 (0.018)

SQ. NOMINAL

5.46 (0.215)

4.95 (0.195)

5.18 (0.204)

4.93 (0.194)

HLMP-S100

2 mm x 5 mm Rectangular LED Lamps

Data Sheet

Summary of content (9 pages)

PAGE 1
HLMP-S100 2 mm x 5 mm Rectangular LED Lamps Data Sheet HLMP-S100, HLMP-S201, HLMP-S301, HLMP-S400, HLMP-S401, HLMP-S501, HLMP-S600 Description The HLMP-S100, -S201, -5301, -S400, -S401, -S501, -S600 are epoxy encapsulated lamps in rectangular packages which are easily stacked in arrays or used for discrete front panel indicators. Contrast and light uniformity are enhanced by a special epoxy diffusion and tinting process.
PAGE 2
Selection Guide Color AlGaAs Red HER Orange Yellow Green Emerald Green[1] Part Number HLMP-S100 HLMP-S201 HLMP-S201-D00xx HLMP-S201-E00xx HLMP-S201-EF0xx HLMP-S400 HLMP-S401 HLMP-S301 HLMP-S301-B00xx HLMP-S301-C00xx HLMP-S301-CDBxx HLMP-S501 HLMP-S501-C00xx HLMP-S501-D00xx HLMP-S501-DE0xx HLMP-S600-A00xx Luminous Intensity Iv (mcd) at 20 mA Min. Typ. Max. 3.4 7.5 – 2.1 3.4 3.4 2.1 3.4 3.5 7.5 7.5 3.5 7.5 – – 10.8 – – 1.4 2.2 2.2 2.1 4.0 4.0 – – 7.2 2.6 4.2 4.2 1.0 4.0 8.0 8.0 3.0 – – 13.
PAGE 3
Electrical/Optical Characteristics at TA = 25°C Sym. 2q1/2 lPEAK Description Included Angle Between Half Luminous Intensity Points Peak Wavelength ld Dominant Wavelength ts Speed of Response C Capacitance RqJ-PIN Thermal Resistance VF Forward Voltage VR hV Reverse Breakdown Voltage Luminous Efficacy Device HLMPAll Min.
PAGE 4
Absolute Maximum Ratings at TA = 25°C Parameter Peak Forward Current Average Forward Current[1] DC Current[2] Transient Forward Current[3] (10 µsec Pulse) LED Junction Temperature Operating Temperature Range Storage Temperature Range AlGaAs Red 300 20 30 110 -20 to +100 -55 to +100 High Efficiency Red/ Orange 90 25 30 500 Yellow 60 20 20 110 110 -55 to +100 -55 to +100 Green/ Emerald Green 90 25 30 110 -20 to +100 -55 to +100 Units mA mA mA mA °C °C Notes: 1.
PAGE 5
70 60 RED 50 YELLOW 40 30 20 GREEN/EMERALD GREEN 10 2.0 2.0 3.0 4.0 5.0 HER, YELLOW, EMERALD GREEN 1.5 1.0 AlGaAs RED 0.5 5 0 20 00 H E–1 4 3 z 2 0.8 50° 0.6 60° 0.4 0.2 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° Figure 6. Relative luminous intensity vs. angular displacement. 5 Hz 1.0 300 0° 30° 90° 1000 tp – PULSE DURATION – µs AlGaAs RED Figure 5. Maximum tolerable peak current vs. peak duration. (IPEAK MAX determined from temperature derated IDC MAX).
PAGE 6
Intensity Bin Limits Color Red/Orange Yellow 6 Bin D E F G H I J K L M N O P Q R S T U V W X Y Z B C D E F G H I J K L M N O P Q R S T U V W Intensity Bin Limits, continued Intensity Range (mcd) Min. Max. 2.4 3.8 3.8 6.1 6.1 9.7 9.7 15.5 15.5 24.8 24.8 39.6 39.6 63.4 63.4 101.5 101.5 162.4 162.4 234.6 234.6 340.0 340.0 540.0 540.0 850.0 850.0 1200.0 1200.0 1700.0 1700.0 2400.0 2400.0 3400.0 3400.0 4900.0 4900.0 7100.0 7100.0 10200.0 10200.0 14800.0 14800.0 21400.0 21400.0 30900.0 1.6 2.5 2.5 4.0 4.0 6.
PAGE 7
Color Categories Color Emerald Green Green Yellow Orange Category # 9 8 7 6 6 5 4 3 2 1 3 2 4 5 1 2 3 4 5 6 7 8 Lambda (nm) Min. Max. 552.5 555.5 555.5 558.5 558.5 561.5 561.5 564.5 561.5 564.5 564.5 567.5 567.5 570.5 570.5 573.5 573.5 576.5 582.0 584.5 584.5 587.0 587.0 589.5 589.5 592.0 592.0 593.0 597.0 599.5 599.5 602.0 602.0 604.5 604.5 607.5 607.5 610.5 610.5 613.5 613.5 616.5 616.5 619.5 Tolerance for each bin limit is ±0.5 nm.
PAGE 8
Precautions Lead Forming • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering into PC board. • If lead forming is required before soldering, care must be taken to avoid any excessive mechanical stress induced to LED package. Otherwise, cut the leads of LED to length after soldering process at room temperature. The solder joint formed will absorb the mechanical stress of the lead cutting from traveling to the LED chip die attach and wirebond.
PAGE 9
For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved.