Datasheet

ManualsBrandsBROADCOM ManualsLEDs & AccessoriesLED wired Blue Circular 5 mm 40 mcd 25 ° 30 mA 3.2 V

HLMP-DB25, HLMP-KB45

T-1¾ (5 mm), T-1 (3 mm)

Blue LED Lamps

Data Sheet

Package Dimensions

Features

• Popular T-1¾ and T-1 diameter packages

• General purpose leads

• Reliable and rugged

• Available on tape and reel

• Binned for color and intensity

Applications

• Status indicators

• Small message panel

• Running and decorative lights for commercial use

Description

These blue LEDs are designed in industry standard T-1 and

T-1¾ package with clear and non diused optics. They are

also available in tape and reel, and ammo-pack option for

ease of handling and use.

These blue lamps are ideal for use as indicators and for

general purpose lighting. Blue lamps oer color dieren-

tiation as blue is attractive and not widely available.

6.10 (0.240)

5.59 (0.220)

23.0

(0.90)

MIN.

0.45 (0.018)

SQUARE NOMINAL

2.54 (0.100)

NOM.

CATHODE

1.27 (0.050)

NOM.

0.89 (0.035)

0.64 (0.025)

9.19 (0.352)

8.43 (0.332)

5.08 (0.200)

4.57 (0.180)

NOTES:

1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).

2. EPOXY MENISCUS MAY EXTEND ABOUT 1 mm (0.040") DOWN THE LEADS.

HLMP-DB25

1.02 (0.040)

NOM.

3.43 (0.135)

2.92 (0.115)

23.0

(0.90)

MIN.

4.70 (0.185)

4.19 (0.165)

3.18 (0.125)

2.67 (0.105)

2.54 (0.100) NOM.

1.27 (0.050)

NOM.

6.35 (0.250)

5.58 (0.220)

0.45 (0.018)

SQUARE NOM.

CATHODE

HLMP-KB45

CAUTION: Devices are Class 1C HBM ESD sensitive per JEDEC Standard. Please observe appropriate pre-

cautions during handling and processing. Refer to Application Note AN-1142 for additional details.

Summary of content (8 pages)

PAGE 1
HLMP-DB25, HLMP-KB45 T-1¾ (5 mm), T-1 (3 mm) Blue LED Lamps Data Sheet Description Features These blue LEDs are designed in industry standard T-1 and T-1¾ package with clear and non diffused optics. They are also available in tape and reel, and ammo-pack option for ease of handling and use. • Popular T-1¾ and T-1 diameter packages These blue lamps are ideal for use as indicators and for general purpose lighting. Blue lamps offer color differentiation as blue is attractive and not widely available.
PAGE 2
Selection Guide Luminous Intensity Iv (mcd) Part Number Package Viewing Angle Min. Max. HLMP-KB45-A0000 T-1 40 30 – HLMP-DB25-B0000 T-1¾ 25 40 – Part Numbering System HLMP - x x xx - x x x xx Mechanical Option 00: Bulk Color Bin Options 0: Full Color Bin Distribution Maximum Iv Bin Options 0: Open (no max.
PAGE 3
Optical Characteristics at TA = 25°C Part Number Luminous Intensity IV (mcd) @ IF = 20 mA Min. Color, Dominant Wavelength ld[1] (nm) Typ. Peak Wavelength lPEAK (nm) Typ. Viewing Angle 2q1/2[2] Degrees Typ. HLMP-DB25-B0000 40 470 464 25 HLMP-KB45-A0000 30 470 464 40 Notes: 1. The dominant wavelength, ld, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 2.
PAGE 4
35 1.2 30 IF – FORWARD CURRENT – mA DC RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 1.4 1.0 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 30 IF – DC FORWARD CURRENT – mA 10° 30° 20 15 10 5 0 0 10 20 30 50° 0° 1.0 .6 60° .4 70° .2 80° 90° 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° Figure 7. Relative luminous intensity vs. angular displacement for HLMP-DB25 20° 30° 40° 50° 10° 0° 1.0 .8 .6 60° 70° 80° 90° .4 .2 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° Figure 8.
PAGE 5
Soldering/Cleaning Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloro-ethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. Intensity Bin Limits Color Bin Limits (nm at 20 mA) Intensity Range (mcd) Min Max Blue nm @ 20 mA Bin ID Bin ID Min. Max.
PAGE 6
Precautions: Lead Forming: • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering on PC board. • For better control, it is recommended to use proper tool to precisely form and cut the leads to applicable length rather than doing it manually. • If manual lead cutting is necessary, cut the leads after the soldering process. The solder connection forms a mechanical ground which prevents mechanical stress due to lead cutting from traveling into LED package.
PAGE 7
Example of Wave Soldering Temperature Profile for TH LED 250 Recommended solder: Sn63 (Leaded solder alloy) SAC305 (Lead free solder alloy) LAMINAR HOT AIR KNIFE TURBULENT WAVE Flux: Rosin flux Solder bath temperature: 245°C± 5°C (maximum peak temperature = 250°C) TEMPERATURE (°C) 200 Dwell time: 1.5 sec – 3.0 sec (maximum = 3sec) 150 Note: Allow for board to be sufficiently cooled to room temperature before exerting mechanical force.
PAGE 8
DeptID: Made In: Country of Origin (ii) Avago Baby Label (Only available on bulk packaging) Lamps Baby Label (1P) PART #: Part Number RoHS Compliant e3 max temp 250C (1T) LOT #: Lot Number (9D)MFG DATE: Manufacturing Date QUANTITY: Packing Quantity C/O: Country of Origin Customer P/N: CAT: Intensity Bin Supplier Code: BIN: Color Bin DATECODE: Date Code For product information and a complete list of distributors, please go to our web site: www.avagotech.