Datasheet

ManualsBrandsBROADCOM ManualsLEDs & AccessoriesLED wired Green Circular 5 mm 70 mcd 24 ° 30 mA 2.1 V

Description

This family of T-1

nondiused LED lamps is

specially designed for applica tions requiring higher

on-axis intensity than is achievable with a standard

lamp. The light generated is focused to a narrow

beam to achieve this eect.

Selection Guide

Luminous Intensity Iv (mcd) @ 10 mA

Color Part Number Min. Max.

Red HLMP-3316 24.8 -

HLMP-3316-I00xx 24.8 -

Yellow HLMP-3416 16.6 -

Green HLMP-3519 12.0 -

HLMP-3519-F00xx 12.0 -

Features

• High intensity

• Choice of 3 bright colors

- High Eciency Red

- Yellow

- High Performance Green

• Popular T-1

diameter package

• Selected minimum intensities

• Narrow viewing angle

• General purpose leads

• Reliable and rugged

• Available on tape and reel

HLMP-331x, HLMP-341x, HLMP-351x Series

T-1

(5 mm) High Intensity LED Lamps

Data Sheet

Summary of content (10 pages)

PAGE 1
HLMP-331x, HLMP-341x, HLMP-351x Series T-13/4 (5 mm) High Intensity LED Lamps Data Sheet Description Features This family of T-13/4 nondiffused LED lamps is specially designed for applica tions requiring higher on-axis intensity than is achievable with a standard lamp. The light generated is focused to a narrow beam to achieve this effect.
PAGE 2
Part Numbering System HLMP - 3 x 1 x - x x x xx Mechanical Options 00: Bulk 01: Tape & Reel, Crimped Leads 02: Tape & Reel, Straight Leads B1: Right Angle Housing, Uneven Leads B2: Right Angle Housing, Even Leads Color Bin Options 0: Full Color Bin Distribution Maximum Iv Bin Options 0: Open (no max.
PAGE 3
Electrical Characteristics at TA = 25°C Symbol Description Device HLMP- Min. Typ. IV 3316 24.8 3416 3519 2q1/2 Luminous Intensity Max. Units Test Conditions 60.0 mcd IF = 10 mA (Figure 3) 16.6 50.0 mcd IF = 10 mA (Figure 8) 12.0 70.0 mcd IF = 10 mA (Figure 13) Including Angle Between Half 3316 35 Deg. Luminous Intensity Points IF = 10 mA See Note 1 (Figure 6) 3416 35 Deg. IF = 10 mA See Note 1 (Figure 11) 3519 24 Deg.
PAGE 4
Absolute Maximum Ratings at TA = 25°C Parameter 331X Series 341X Series 351X Series Units Peak Forward Current 90 60 90 mA Average Forward Current[1] 25 20 25 mA DC Current[2] 30 20 30 mA Power Dissipation[3] 135 85 135 mW Reverse Voltage (IR = 100 µA) 5 5 5 V Transient Forward Current[4] (10 µsec Pulse) 500 500 500 mA LED Junction Temperature 110 110 110 °C Operating Temperature Range -40 to +100 -40 to +100 -20 to +100 °C Storage Temperature Range -40 to +100
PAGE 5
High Efficiency Red HLMP-331X Series Figure 2. Forward current vs. forward voltage characteristics. Figure 5. Maximum tolerable peak current vs. pulse duration (IDC MAX as per MAX ratings). 5 Figure 3. Relative luminous intensity vs. DC forward current. Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak LED current. Figure 6. Relative luminous intensity vs. angular displacement.
PAGE 6
Yellow HLMP-341X Series Figure 7. Forward current vs. forward voltage characteristics. Figure 10. Maximum tolerable peak current vs. pulse duration (IDC MAX as per MAX ratings). 6 Figure 8. Relative luminous intensity vs. DC forward current. Figure 9. Relative efficiency (luminous intensity per unit current) vs. peak current. Figure 11. Relative luminous intensity vs. angular displacement.
PAGE 7
Green HLMP-351X Series Figure 12. Forward current vs. forward voltage characteristics. Figure 15. Maximum tolerable peak current vs. pulse duration (IDC MAX as per MAX ratings). 7 Figure 13. Relative luminous intensity vs. DC forward current. Figure 14. Relative efficiency (luminous intensity per unit current) vs. peak LED current. Figure 16. Relative luminous intensity vs. angular displacement. T-13/4 lamp.
PAGE 8
Table 2. Intensity Bin Limit Table 2. (Cont'd) Table 2. (Cont'd) Intensity Range (mcd) Intensity Range (mcd) Intensity Range (mcd) Color Color Color Red Bin Min. Max. Bin Min. Max. H 15.5 24.8 G 16.6 26.5 I 24.8 39.6 H 26.5 42.3 J 39.6 63.4 I 42.3 K 63.4 101.5 J 67.7 L 101.5 162.4 K M 162.4 234.6 L N 234.6 340.0 O 340.0 540.0 P 540.0 Q 850.0 R Min. Max. E 7.6 12.0 F 12.0 19.1 67.7 G 19.1 30.7 108.2 H 30.7 49.
PAGE 9
Color Categories Lambda (nm) Color Green Yellow Cat # Min. Max. 6 561.5 564.5 5 564.5 567.5 4 567.5 570.5 3 570.5 573.5 2 573.5 576.5 1 582.0 584.5 3 584.5 587.0 2 587.0 589.5 4 589.5 592.0 5 592.0 593.0 Tolerance for each bin limit is ± 0.5 nm.
PAGE 10
Precautions Lead Forming • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering into PC board. • If lead forming is required before soldering, care must be taken to avoid any excessive mechanical stress induced to LED package. Otherwise, cut the leads of LED to length after soldering process at room temperature. The solder joint formed will absorb the mechanical stress of the lead cutting from traveling to the LED chip die attach and wirebond.