Datasheet

ManualsBrandsBROADCOM ManualsLEDs & AccessoriesLED wired Green Circular 3 mm 22 mcd 45 ° 30 mA 2.1 V

Features

• High intensity

• Choice of 3 bright colors

High Eciency Red

Yellow

High Performance Green

• Popular T-1 diameter package

• Selected minimum intensities

• Narrow viewing angle

• General purpose leads

• Reliable and rugged

• Available on tape and reel

• For more information, please refer to Tape and Reel

Option data sheet

Description

This family of T-1 lamps is specially designed for applica-

tions requiring higher on-axis intensity than is achiev-

able with a standard lamp. The light generated is focused

to a narrow beam to achieve this eect.

Package Dimensions

HLMP-132x Series, HLMP-142x Series,

HLMP-152x Series

T-1 (3 mm) High Intensity LED Lamps

Data Sheet

Selection Guide

Part Number

Package

Description Color

Luminous Intensity

Iv (mcd) @ 10 mA

Min. Max.

HLMP-1321 Tinted,

Non-diused

High Eciency

Red

8.6 –

HLMP-1321-G00xx 8.6 –

HLMP-1420 Microtinted,

Non-diused

Yellow

9.2 –

HLMP-1421 Tinted,

Non-diused

9.2 –

HLMP-1421-F00xx 9.2 –

HLMP-1520 Microtinted,

Non-diused

Green

6.7 –

HLMP-1521 Tinted,

Non-diused

6.7 –

HLMP-1521-E00xx 6.7 –

Notes:

1. All dimensions are in millimeters (inches).

2. An epoxy meniscus may extend about 1 mm (0.40") down the leads.

3. For PCB hole recommendations, see the Precautions section.

0.65 (0.026) max.

24.1(.95) min.

4.70 (.185)

4.19 (.165)

3.43 (.135)

2.92 (.115)

1.52 (.060)

1.02 (.040)

2.79 (.110)

2.29 (.090)

1.14 (.045)

0.51 (.020)

(0.022) 0.55

SQ. TYP.

(0.016) 0.40

3.17 (.125)

2.67 (.105)

6.35 (.250)

5.58 (.220)

Summary of content (9 pages)

PAGE 1
HLMP-132x Series, HLMP-142x Series, HLMP-152x Series T-1 (3 mm) High Intensity LED Lamps Data Sheet Description Features This family of T-1 lamps is specially designed for applica tions requiring higher on-axis intensity than is achievable with a standard lamp. The light generated is focused to a narrow beam to achieve this effect.
PAGE 2
Part Numbering System HLMP - 1 x xx - x x x xx Mechanical Option 00: Bulk 01: Tape & Reel, Crimped Leads 02: Tape & Reel, Straight Leads A1: Right Angle Housing, Uneven Leads A2: Right Angle Housing, Even Leads Color Bin Options 0: Full Color Bin Distribution Maximum Iv Bin Options 0: Open (no max.
PAGE 3
Electrical Characteristics at TA = 25°C Symbol Description IV Luminous Intensity Device HLMP- Min. Typ. Max. Units Test Conditions 1320 1321 8.6 8.6 30 30 mcd IF = 10 mA (Figure 3) 1420 1421 9.2 9.2 15 15 mcd IF = 10 mA (Figure 8) 1520 1521 6.7 6.7 22 22 mcd IF = 10 mA (Figure 3) 2q1/2 Including Angle Between Half Luminous Intensity Points All 45 Deg.
PAGE 4
Figure 1. Relative intensity vs. wavelength. 1.6 1.6 80 80 80 3.5 3.5 3.5 1.5 1.5 1.5 70 70 60 60 50 50 40 40 30 30 20 20 10 10 70 3.0 60 50 40 30 20 10 0 0 0 1.0 1.0 2.0 1.02.0 3.0 2.03.0 4.0 3.04.0 5.0 4.05.0 5.0 VF – FORWARD VF – FORWARD VFVOLTAGE – FORWARD VOLTAGE – V VOLTAGE –V –V Figure 2. Forward current vs. forward voltage characteristics.
PAGE 5
T-1 Yellow Non-Diffused 0 1.0 30 30 20 20 10 10 0 0 1.5 1.0 1.02.0 1.5 1.52.5 2.0 2.03.0 2.5 2.53.5 3.0 3.04.0 3.5 3.5 4.0 4.0 VF – FORWARD – FORWARD – V VOLTAGE VF – VFORWARD VOLTAGE –V –V F VOLTAGE TA = 25° T =T25° = 25° A A 2.0 2.0 2.0 1.5 1.5 1.5 1.0 1.0 1.0 0.5 0 0.5 0.
PAGE 6
20 10 0 1.0 30 20 10 50 40 30 20 10 0 2.0 1.0 0 3.0 2.0 1.0 4.0 3.0 2.0 5.0 4.0 3.0 5.0 4.0 5.0 3.0 3.0 3.0 2.5 2.5 2.5 2.0 2.0 2.0 1.5 1.5 1.0 1.0 1.0 0.5 0.5 0 0 Figure 12. Forward current vs. forward voltage characteristics. 5 010 5 4 4 3 3 1.6 1.5 1.5 1.5 1.4 1.3 1.2 1.1 1.0 1.3 1.2 1.1 1.0 1.4 1.3 1.2 1.1 1.0 0.9 0.9 0.5 0.8 0.8 0.8 0 515 01020 51525102030152535203040 2535 3040 35 0.7 40 0 Figure 13. Relative luminous intensity vs. forward current.
PAGE 7
Intensity Bin Limits Intensity Bin Limits Intensity Range (mcd) Color Red Yellow 7 Bin Min. Max. G 9.7 H I Intensity Range (mcd) Color Bin Min. Max. 15.5 E 7.6 12.0 15.5 24.8 F 12.0 19.1 24.8 39.6 G 19.1 30.7 J 39.6 63.4 H 30.7 49.1 K 63.4 101.5 I 49.1 78.5 L 101.5 162.4 J 78.5 125.7 M 162.4 234.6 K 125.7 201.1 N 234.6 340.0 L 201.1 289.0 O 340.0 540.0 M 289.0 417.0 P 540.0 850.0 N 417.0 680.0 Q 850.0 1200.0 O 680.0 1100.
PAGE 8
Color Categories Lambda (nm) Color Green Yellow Category # Min. Max. 6 561.5 564.5 5 564.5 567.5 4 567.5 570.5 3 570.5 573.5 2 573.5 576.5 1 582.0 584.5 3 584.5 587.0 2 587.0 589.5 4 589.5 592.0 5 592.0 593.0 Maximum tolerance for each bin limit is ±0.5 nm.
PAGE 9
Precautions: Lead Forming • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering into PC board. • If lead forming is required before soldering, care must be taken to avoid any excessive mechanical stress induced to LED package. Otherwise, cut the leads of LED to length after soldering process at room temperature. The solder joint formed will absorb the mechanical stress of the lead cutting from traveling to the LED chip die attach and wirebond.