Datasheet

ManualsBrandsBROADCOM ManualsLEDs & AccessoriesLED indicator light (multi-colour) Red, Green Rectangular 2 x 5 mm 2.1 mcd, 2.6 mcd 100 ° 20 mA, 20 mA 1.9 V, 2.2 V Broa

Description

The T-1 3/4 HLMP-40xx and 2 mm by 5 mm

rectangular HLMP-08xx are three leaded bicolor

light sources designed for a variety of applications

where dual state illumination is required in the same

package. There are two LED chips, mounted on a

central common cathode lead for maximum on-axis

viewability. Colors between the two chips can be

generated by independently pulse width modulating

the LED chips.

Features

• Two color operation

• Three leads with one common cathode

• Option of straight or spread leads configuration

• Diffused, wide visibility range

Selection Guide

Min. Luminous Intensity Iv (mcd)

Package Part Number Color Green Red Yellow I

(mA)

T-1 3/4 HLMP-4000 Green/HER 4.2 2.1 10

HLMP-4000#xxx 4.2 2.1 10

HLMP-4015 Green/Yellow 20.0 20 20

Rectangular HLMP-0800 Green/HER 2.6 2.1 20

HLMP-0805 Green/Yellow 2.6 1.4 20

HLMP-40xx/HLMP-08xx

T-1 3/4, 2 mm x 5 mm Rectangular Bicolor LED Lamps

Data Sheet

Summary of content (7 pages)

PAGE 1
HLMP-40xx/HLMP-08xx T-1 3/4, 2 mm x 5 mm Rectangular Bicolor LED Lamps Data Sheet Description The T-1 3/4 HLMP-40xx and 2 mm by 5 mm rectangular HLMP-08xx are three leaded bicolor light sources designed for a variety of applications where dual state illumination is required in the same package. There are two LED chips, mounted on a central common cathode lead for maximum on-axis viewability. Colors between the two chips can be generated by independently pulse width modulating the LED chips.
PAGE 2
Part Numbering System HLMP - X X X X # X X X Mechanical Options 002: Tape & Reel, Straight Leads 010: Right Angle Housing, Even Leads Color Options 00: High Efficiency Red (HER)/High Efficiency Green 05/15: Yellow/High Efficiency Green Package Options 40: T-1 3/4 (5 mm) 08: Rectangular Package Dimensions 2.23 (0.088) 1.98 (0.078) 5.08 (0.200) 4.57 (0.180) 5.18 (0.204) 4.93 (0.194) 8.00 (0.315) 7.37 (0.290) 9.19 (0.362) 8.43 (0.332) 25.40 (1.00) MIN. 1.27 (0.050) NOM. 0.89 (0.035) 0.64 (0.
PAGE 3
Absolute Maximum Ratings at TA = 25°C Parameter Peak Forward Current Average Forward Current[1,2] (Total) DC Current[2] (Total) Power Dissipation[3] (Total) Operating Temperature Range Storage Temperature Range Reverse Voltage (IR = 100 µA) Transient Forward Current[4] (10 µsec Pulse) HER/Green 90 25 30 135 –20 to +100 –55 to +100 5 500 Yellow/Green 60 20 20 135 –20 to +100 –55 to +100 5 500 Units mA mA mA mW °C °C V mA Notes: 1. See Figure 5 to establish pulsed operating conditions. 2.
PAGE 4
1.0 RELATIVE INTENSITY TA = 25° C ORANGE EMERALD GREEN HIGH PERFORMANCE GREEN HIGH EFFICIENCY RED 0.5 YELLOW 0 500 550 600 650 700 750 WAVELENGTH – nm Figure 1. Relative intensity vs. wavelength. HIGH EFFICIENCY RED, ORANGE, YELLOW, AND HIGH PERFORMANCE GREEN, EMERALD GREEN HER, ORANGE, YELLOW, AND HIGH PERFORMANCE GREEN, EMERALD GREEN 1.6 HIGH PERFORMANCE GREEN, EMERALD GREEN 80 HIGH EFFICIENCY RED/ORANGE 60 YELLOW 40 20 0 1.0 0 2.0 3.0 4.
PAGE 5
20° 10° 0° 1.0 30° 0.8 40° 50° 0.6 60° 0.4 70° 0.2 80° 90° 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° Figure 6. Relative luminous intensity vs. angular displacement for HLMP-40xx. 20° 10° 30° 40° 0° 1.0 0.8 50° 0.6 60° 70° 80° 90° 0.4 0.2 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° Figure 7. Relative luminous intensity vs. angular displacement for HLMP-08xx.
PAGE 6
Precautions Lead Forming • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering into PC board. • If lead forming is required before soldering, care must be taken to avoid any excessive mechanical stress induced to LED package. Otherwise, cut the leads of LED to length after soldering process at room temperature. The solder joint formed will absorb the mechanical stress of the lead cutting from traveling to the LED chip die attach and wirebond.
PAGE 7
For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Limited. All rights reserved.