Datasheet

ManualsBrandsBROADCOM ManualsLEDs & AccessoriesLED indicator light (multi-colour) Red, Green Rectangular 2 x 5 mm 2.1 mcd, 2.6 mcd 100 ° 20 mA, 20 mA 1.9 V, 2.2 V Broa

Description

The T-1 3/4 HLMP-40xx and 2 mm by 5 mm rectangular

HLMP-08xx are three leaded bicolor light sources de-

signed for a variety of applications where dual state illu-

mination is required in the same package. There are two

LED chips, mounted on a central common cathode lead

for maximum on-axis viewability. Colors between the two

chips can be generated by independently pulse width

modulating the LED chips.

Features

• Two color operation

• Three leads with one common cathode

• Option of straight or spread leads conguration

Selection Guide

Package Part Number Color Package lens

Min. Luminous Intensity Iv (mcd)

Green Red Yellow I

(mA)

T-1 3/4 HLMP-4000 Green/HER Non tinted, diused 4.2 2.1 10

HLMP-4000#xxx 4.2 2.1 10

HLMP-4015 Green/Yellow Non tinted, non-diused 20.0 20 20

Rectangular HLMP-0800 Green/HER Non tinted, diused 2.6 2.1 20

HLMP-0805 Green/Yellow Non tinted, diused 2.6 1.4 20

HLMP-40xx, HLMP-08xx

T-1 3/4, 2 mm x 5 mm Rectangular Bicolor LED Lamps

Data Sheet

Summary of content (6 pages)

PAGE 1
HLMP-40xx, HLMP-08xx T-1 3/4, 2 mm x 5 mm Rectangular Bicolor LED Lamps Data Sheet Description Features The T-1 3/4 HLMP-40xx and 2 mm by 5 mm rectangular HLMP-08xx are three leaded bicolor light sources designed for a variety of applications where dual state illumination is required in the same package. There are two LED chips, mounted on a central common cathode lead for maximum on-axis viewability. Colors between the two chips can be generated by independently pulse width modulating the LED chips.
PAGE 2
Part Numbering System HLMP - X X X X # X X X Mechanical Options 002: 010: Tape & Reel, Straight Leads Right Angle Housing, Even Leads Color Options 00: High Efficiency Red (HER)/High Efficiency Green 05/15: Yellow/High Efficiency Green Package Options 40: 08: T-1 3/4 (5 mm) Rectangular Package Dimensions 2.23 (0.088) 1.98 (0.078) 5.08 (0.200) 4.57 (0.180) 8.00 (0.315) 7.37 (0.290) 9.19 (0.362) 8.43 (0.332) 0.89 (0.035) 0.64 (0.025) 25.40 (1.00) MIN. COMMON CATHODE 1.27 (0.050) NOM. 0.508 (0.
PAGE 3
Absolute Maximum Ratings at TA = 25°C Parameter HER/Green Yellow/Green Units Peak Forward Current 90 60 mA Average Forward Current[1,2] (Total) 25 20 mA DC Current[2] (Total) 30 20 mA Power Dissipation[3] (Total) 135 135 mW Operating Temperature Range –20 to +100 –20 to +100 °C Storage Temperature Range –40 to +100 –40 to +100 °C Reverse Voltage (IR = 100 µA) 5 5 V Transient Forward Current[4] (10 µsec Pulse) 500 500 mA Notes: 1.
PAGE 4
RELATIVE INTENSITY 1.0 TA = 25° C ORANGE EMERALD GREEN HIGH PERFORMANCE GREEN HIGH EFFICIENCY RED 0.5 YELLOW 0 500 550 600 650 700 750 WAVELENGTH – nm Figure 1. Relative intensity vs. wavelength. HIGH EFFICIENCY RED, ORANGE, YELLOW, AND HIGH PERFORMANCE GREEN, EMERALD GREEN 1.
PAGE 5
20° 10° 0° 1.0 30° 0.8 40° 50° 0.6 60° 0.4 70° 0.2 80° 90° 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° Figure 6. Relative luminous intensity vs. angular displacement for HLMP-40xx. 20° 30° 40° 50° 10° 0° 1.0 0.8 0.6 60° 70° 80° 0.4 0.2 90° 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° Figure 7. Relative luminous intensity vs. angular displacement for HLMP-08xx.
PAGE 6
Precautions: Lead Forming • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering into PC board. • If lead forming is required before soldering, care must be taken to avoid any excessive mechanical stress induced to LED package. Otherwise, cut the leads of LED to length after soldering process at room temperature. The solder joint formed will absorb the mechanical stress of the lead cutting from traveling to the LED chip die attach and wirebond.