Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysDarlington Transistor-Output Optocoupler SO 8 Type (misc.) 100 kBd, 2-channel, 3.3 V

Description

These high gain series couplers use a Light Emitting Di-

ode and an integrated high gain photodetector to pro-

vide extremely high current transfer ratio between input

and output. Separate pins for the photodiode and out-

put stage result in LVTTL compatible saturation voltages

and high speed operation. Where desired, the V

and V

terminals may be tied together to achieve conventional

photo-darlington operation. A base access terminal al-

lows a gain bandwidth adjustment to be made.

These optocouplers are for use in LVTTL/LVCMOS or

other low power applications. A 400% minimum current

transfer ratio is guaranteed over 0 to +70˚C operating

range for only 0.5 mA of LED current.

The HCPL-070L and HCPL-073L are surface mount de-

vices packaged in an industry standard SOIC-8 footprint.

The SOIC-8 does not require "through holes" in a PCB.

This package occupies approximately one-third the foot-

print area of the standard dual-in-line package. The lead

prole is designed to be compatible with standard sur-

face mount processes.

Functional Diagram

Features

• 3.3V/5V Dual Supply Voltages

• Low power consumption

• High current transfer ratio

• Low input current requirements – 0.5 mA

• LVTTL/LVCMOS compatible output

• Performance guaranteed over temperature 0°C to +70°C

• Base access allows gain bandwidth adjustment

• High output current – 60 mA

• Safety approval, UL, IEC/EN/DIN EN 60747-5-2, CSA

Applications

• Ground isolate most logic families – LVTTL/LVCMOS

• Low input current line receiver

• High voltage insulation

• EIA RS-232C line receiver

• Telephone ring detector

• V AC line voltage status indicator – low input power

dissipation

• Low power systems – ground isolation

A 0.1 µF bypass capacitor connected between pins 8 and 5 is recommended.

CAUTION: It is advised that normal static precautions be taken in handling and assembly

of this component to prevent damage and/or degradation which may be induced by ESD.

HCPL-270L/070L/273L/073L

Low Input Current, High Gain, LVTTL/LVCMOS Compatible Optocouplers

Data Sheet

ANODE

CATHODE

GND

TRUTH TABLE

HCPL-270L/070L HCPL-273L/073L

LED

OFF

LOW

HIGH

GND

ANODE

CATHODE

ANODE

SHIELD

Summary of content (12 pages)

PAGE 1
HCPL-270L/070L/273L/073L Low Input Current, High Gain, LVTTL/LVCMOS Compatible Optocouplers Data Sheet Description Features These high gain series couplers use a Light Emitting Diode and an integrated high gain photodetector to provide extremely high current transfer ratio between input and output. Separate pins for the photodiode and output stage result in LVTTL compatible saturation voltages and high speed operation.
PAGE 2
Ordering Information HCPL-270L, HCPL-273L, HCPL-070L and HCPL-073L are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are approved under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 3
Selection Guide 8-Pin DIP (300 Mil) Small Outline SO-8 Single Channel Package HCPL- Dual Channel Package HCPL- Single Channel Package HCPL- Dual Channel Package HCPL- Minimum Input ON Current (IF) Minimum CTR 270L 273L 070L 073L 0.5 mA 400% Schematic V CC 1 8 + I CC ANODE 2 8 V CC V F1 IF + - VF CATHODE I CC I F1 I O1 2 IO 3 6 VO 3 5 SHIELD 7 I F2 - I O2 GND 6 V F2 IB VB V O1 V O2 7 + 4 5 SHIELD USE OF A 0.
PAGE 4
Package Outline Drawings 8-Pin DIP Package 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) TYPE NUMBER 8 7 6 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* DATE CODE A XXXXZ YYWW RU 1 2 3 UL RECOGNITION 4 1.78 (0.070) MAX. 1.19 (0.047) MAX. + 0.076 - 0.051 + 0.003) (0.010 - 0.002) 0.254 5° TYP. 3.56 ± 0.13 (0.140 ± 0.005) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 ± 0.320 (0.043 ± 0.013) DIMENSIONS IN MILLIMETERS AND (INCHES).
PAGE 5
Solder Reflow Temperature Profile 300 PREHEATING RATE 3°C + 1°C/-0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. 200 PEAK TEMP. 245°C PEAK TEMP. 240°C TEMPERATURE (°C) 2.5°C ± 0.5°C/SEC. 30 SEC. 160°C 150°C 140°C PEAK TEMP. 230°C SOLDERING TIME 200°C 30 SEC. 3°C + 1°C/-0.5°C 100 PREHEATING TIME 150°C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 150 200 250 TIME (SECONDS) Note: Non-halide flux should be used.
PAGE 6
Insulation and Safety Related Specifications Parameter Symbol 8-Pin DIP (300 Mil) Value SO-8 Value Units Conditions Minimum External Air L (101) 7.1 4.9 mm Gap (External Clearance) Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking L (102) 7.4 4.8 mm (External Creepage) Measured from input terminals to output terminals, shortest distance path along body. Minimum Internal Plastic 0.08 0.
PAGE 7
Absolute Maximum Ratings (No Derating Required up to +85˚C) Parameter Symbol Min. Max. Units Storage Temperature TS –55 125 ˚C Operating Temperature TA –40 85 ˚C Average Forward Input Current IF(AVG) 20 mA Peak Forward Input Current (50% Duty Cycle, 1 ms Pulse Width) IF(PEAK) 40 mA Peak Transient Input Current (< 1 µs Pulse Width, 300 pps) IF(TRAN) 1.
PAGE 8
Electrical Specifications 0˚C ≤ TA ≤ +70˚C, 2.7 V ≤ VCC ≤ 3.3 V, 0.5 mA ≤ IF(ON) ≤ 12 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specified. All typicals at TA = 25˚C. (See Note 8.) Parameter Sym. Device HCPL- Min. Typ.* Max. Units Test Conditions Current Transfer CTR 400 1300 5000 % IF = 0.5 mA Ratio VCC = 3.3 V VO = 0.4 V Logic Low VOL 0.05 0.3 V Output Voltage IF = 1.6 mA, IO = 8 mA VCC = 3.3 V 0.05 0.4 V IF = 5.
PAGE 9
Switching Specifications (AC) Over Recommended Operating Conditions (TA = 0˚C to +70˚C), VCC = 3.3 V, unless otherwise specified. (See Note 8.) Parameter Sym. Max. Units Test Conditions Fig. Note Propagation Delay Time to Logic Low at Output tPHL Min. Typ.* 30 µs IF = 0.5 mA, Rl = 4.7 kΩ 5 2 Propagation Delay Time to Logic High at Output tPLH 90 µs IF = 0.5 mA, RL = 4.
PAGE 10
Package Characteristics Parameter Sym. Device HCPL- Min. Typ.* Max. Units Test Conditions Fig. Note Input-Output VISO 3750 V rms Momentary Withstand Voltage** RH ≤ 50%, t = 1 min., TA = 25˚C 4, 9 Resistance RI-O 1012 Ω (Input-Output) VI-O = 500 Vdc RH ≤ 45% 4 Capacitance (Input-Output) pF f = 1 MHz 11 Input-Input II-I 0.
PAGE 11
CTR - CURRENT TRANSFER RATIO - % 25°C 1600 70°C -40°C 1200 800 V CC = 3.3 V V O = 0.4 V 400 0 0.1 1.0 T A = 25° C 2000 T A = 70° C T A = 85° C 1500 T A = -40° C 1000 500 0 10 0.1 1.0 IF - FORWARD CURRENT - mA T A = 85° C T A = 25° C T A = -40° C 0.1 1 TA = 70°C 0.1 TA = 25°C 0.001 10 1.5 1.4 1.3 TA = -40°C 1.1 1.2 1.3 1.4 1.5 1.2 -60 -40 1.6 -20 VF - FORWARD VOLTAGE - V Figure 5. Input diode forward current vs. forward voltage 0 20 3.
PAGE 12
PULSE GEN. Z O = 50 W t r = 5 ns IF 5V VO 1.5 V IF RL V OL t PHL 5V 2 7 3 6 VO C L = 15 pF 0.1µF IF MONITOR IF 0 +5 V 8 1 5 4 RM VO 1.5 V V OL t PLH Figure 8. Switching test circuit 10 V V CM 0V 90% IF tr, tf = 16 ns 90% 10% tf VO A 3.3 V V FF SWITCH AT A: I F = 0 mA VO 8 2 7 3 6 4 5 V CM + V OL SWITCH AT B: IF = 1.6 mA R CC (SEE NOTE 6) RL VO - PULSE GEN. Figure 9.