Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysIntelligent-Power-Module-Interface-Optocoupler SO 8 Type (misc.) 1 MBd

Description

These diode-transistor opto coup lers use an insulating

layer between a LED and an integrated photodetector to

provide elec trical in su lation between input and out put.

Separate connections for the photodiode bias and out-

put-transistor collector increase the speed up to a hun-

dred times that of a conven tional phototransistor coupler

by reduc ing the base-collector capacitance.

These single channel optocoup lers are available in

8-Pin DIP , SO-8 and Widebody package conﬁgurations.

The HCPL-4502/4503 and HCNW4502/4503 are designed

for high speed TTL/TTL applications. A standard 16 mA TTL

sink current through the input LED will provide enough

output current for 1 TTL load and a 5.6 kΩ pull-up resistor.

CTR for these devices is 19% minimum at I

= 16 mA.

Functional Diagram

A 0.1 µF bypass capacitor must be connected between pins 5 and 8.

HCNW4502/3

HCPL-0452/0453/4502/4503

Single Channel, High Speed Optocouplers

Data Sheet

Features

• 15 kV/µs minimum common mode transient

immunity at V

= 1500 V

• High speed: 1 Mb/s

• TTL compatible

• Available in 8-Pin DIP, SO-8, widebody packages

• Open collector output

• Guaranteed performance from temperature:

0°C to 70°C

• Safety approval

UL Recognized – 3750 V

rms

for 1 minute (5000 V

rms

for 1 minute for HCNW and Option 020 devices)

per UL1577

CSA Approved

IEC/EN/DIN EN 60747-5-2 Approved

– V

IORM

= 630 V peak for HCPL-4503#060

– V

IORM

= 1414 V peak for HCNW devices

• Dual channel version available (4534/0534)

• MIL-PRF-38534 hermetic version available

(55XX/65XX/4N55)

Applications

• High voltage insulation

• Video signal isolation

• Power transistor isolation in motor drives

• Line receivers

• Feedback element in switched mode power supplies

• High speed logic ground isolation

– TTL/TTL, TTL/CMOS, TTL/LSTTL

• Replaces pulse transformers

• Replaces slow phototransistor isolators

• Analog signal ground isolation

Lead (Pb) Free

RoHS 6 fully

compliant

RoHS 6 fully compliant options available;

-xxxE denotes a lead-free product

CAUTION: It is advised that normal static precautions be taken in handling and assembly

of this component to prevent damage and/or degradation which may be induced by ESD.

ANODE

CATHODE

GND

TRUTH TABLE

(POSITIVE LOGIC)

LED

OFF

LOW

HIGH

Summary of content (16 pages)

PAGE 1
HCNW4502/3 HCPL-0452/0453/4502/4503 Single Channel, High Speed Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output.
PAGE 2
The HCPL-4502, HCPL-0452, and HCNW4502 provide the electrical and switching performance of the 6N136, HCPL0501, and HCNW136 with increased ESD protection. The HCPL-4503, HCPL-0453, and HCNW4503 are similar to the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers but have increased common mode transient immunity of 15 kV/µs minimum at VCM = 1500 V guaranteed.
PAGE 3
Ordering Information HCPL-4502 and HCPL-4503, HCPL-0452, HCPL-0453 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW4502 and HCNW4503 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All devices above listed are approved under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 4
Package Outline Drawings 8-Pin DIP Package (HCPL-4502/3) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 8 TYPE NUMBER 7 6 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* DATE CODE A XXXXZ YYWW RU 1 2 3 UL RECOGNITION 4 1.78 (0.070) MAX. 1.19 (0.047) MAX. 5° TYP. 3.56 ± 0.13 (0.140 ± 0.005) 4.70 (0.185) MAX. 0.254 + 0.076 - 0.051 + 0.003) (0.010 - 0.002) 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 ± 0.320 (0.043 ± 0.013) Dimensions in millimeters and (inches).
PAGE 5
Small Outline SO-8 Package (HCPL-0452/3) LAND PATTERN RECOMMENDATION 8 7 6 5 5.994 ± 0.203 (0.236 ± 0.008) TYPE NUMBER (LAST 3 DIGITS) DATE CODE XXX YWW 3.937 ± 0.127 (0.155 ± 0.005) 1 PIN ONE 0.406 ± 0.076 (0.016 ± 0.003) 2 3 7.49 (0.295) 1.9 (0.075) 4 1.270 BSC (0.050) 0.64 (0.025) * 5.080 ± 0.127 (0.200 ± 0.005) 7° 3.175 ± 0.127 (0.125 ± 0.005) 0.432 45° X (0.017) 0 ~ 7° 1.524 (0.060) 0.228 ± 0.025 (0.009 ± 0.001) 0.203 ± 0.102 (0.008 ± 0.
PAGE 6
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW4502/3) 11.15 ± 0.15 (0.442 ± 0.006) 8 7 6 LAND PATTERN RECOMMENDATION 5 9.00 ± 0.15 (0.354 ± 0.006) 1 2 3 13.56 (0.534) 4 2.29 (0.09) 1.3 (0.051) 1.55 (0.061) MAX. 12.30 ± 0.30 (0.484 ± 0.012) 11.00 MAX. (0.433) 4.00 (0.158) MAX. 1.78 ± 0.15 (0.070 ± 0.006) 2.54 (0.100) BSC 0.75 ± 0.25 (0.030 ± 0.010) 1.00 ± 0.15 (0.039 ± 0.006) 0.076 0.254 -+0.0051 0.003) (0.010 + - 0.002) Dimensions in millimeters (inches). 7° NOM.
PAGE 7
Recommended Pb-Free IR Profile tp * 260 +0/-5°C TEMPERATURE Tp TL 217°C Tsmax Tsmin 150 - 200°C RAMP-UP 3°C/SEC. MAX. 15 SEC. RAMP-DOWN 6°C/SEC. MAX. ts PREHEAT 60 to 180 SEC. 25 TIME WITHIN 5°C of ACTUAL PEAK TEMPERATURE tL Notes: The time from 25°C to peak Temperature = 8 minutes max. Tsmax = 200°C, tsmin = 150°C 60 to 150 SEC. Non-halide flux should be used.
PAGE 8
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (Option 060 ONLY) Description Symbol Characteristic HCPL-4502/4503 HCPL-0452/0453 Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤300 V rms I-IV I-III for rated mains voltage ≤450 V rms I-III Climatic Classification 55/100/21 Units 55/100/21 Pollution Degree (DIN VDE 0110/1.
PAGE 9
Absolute Maximum Ratings Parameter Symbol Device Storage Temperature TS Min. Max.
PAGE 10
Electrical Specifications (DC) Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. See note 13. Parameter Symbol Device Current Transfer Ratio CTR Typ.* Max. 24 24 50 TA = 25°C VO = 0.4 V VO = 0.5 V IF = 16 mA, 1, 2, VCC = 4.5 V 4 0.1 0.1 0.4 0.5 TA = 25°C IO = 3.0 mA IO = 2.4 mA IF = 16 mA, VCC = 4.5 V Logic High IOH Output Current 0.003 0.01 µA Logic Low ICCL Supply Current Logic High ICCH Supply Current 50 0.5 1 50 200 0.
PAGE 11
Switching Specifications (AC) Over recommended temperature (TA = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specified. Parameter Sym. Device Min. Typ.* Max. Units Test Conditions Fig. Note Propagation tPHL Delay Time to Logic Low at Output Propagation tPLH Delay Time to Logic High at Output HCPL-4502/3 0.2 HCPL-0452/3 HCNW4502/3 0.8 TA = 25°C RL = 1.9 kΩ 1.0 5, 6, 10 8 HCPL-4502/3 0.6 HCPL-0452/3 HCNW4502/3 0.8 TA = 25°C RL = 1.9 kΩ 1.
PAGE 12
Package Characteristics Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. Parameter Sym. Input-Output VISO Momentary Withstand Voltage** Device Min. Typ.* Max. Units Note RH < 50%, t = 1 min., 6, 11 Widebody TA = 25°C 6, 12 5000 8-Pin DIP 5000 (Option 020) 6, 13 6 1012 Ω VI-O = 500 Vdc Widebody 1013 TA = 25°C 1012 10 11 8-Pin DIP SO-8 0.6 Widebody 0.
PAGE 13
8 PIN DIP, SO-8 TA = 25°C VCC = 5.0 V 35 mA IO - D OUTPUT CURRENT - mA IO - D OUTPUT CURRENT - mA 10 30 mA 25 mA 5 0 20 mA 15 mA 10 mA IF = 5 mA 0 10 VO - OUTPUT VOLTAGE - V WIDEBODY 16 40 mA 40 mA 35 mA 30 mA 25 mA 20 mA 15 mA 10 mA 12 8 4 IF = 5 mA 0 20 TA = 25°C VCC = 5.0 V 0 10 VO - OUTPUT VOLTAGE - V 20 8 PIN DIP, SO-8 1.5 HCPL-4502/3, HCPL-0452/0453 1.0 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25C 0.5 0.1 0 WIDEBODY 1.
PAGE 14
NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO 8 PIN DIP, SO-8 1.1 1.0 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25C 0.9 0.8 0.7 0.6 HCPL-4502/3, HCPL-0452/0453 -60 -40 - 20 20 40 60 0 TA - TEMPERATURE - °C 80 100 WIDEBODY 1.1 1.0 HCNW4502/3 0.9 0.8 0.7 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25C 0.6 0.5 0.4 -60 -40 -20 0 20 40 60 TA - TEMPERATURE - °C 80 100 Figure 4. Current transfer ratio vs. temperature.
PAGE 15
IF = 0 VO = VCC = 5.0 V 10+3 10+2 10+1 100 10-1 10-2 -75 -50 -25 0 +25 +50 TA - TEMPERATURE - °C +75 WIDEBODY 10+3 IOH - LOGIC HIGH OUTPUT CURRENT - nA IOH - LOGIC HIGH OUTPUT CURRENT - nA 8 PIN DIP, SO-8 10+4 IF = 0 VO = VCC = 15 V 10+2 10+1 100 +100 -60 -20 -40 0 20 40 TA - TEMPERATURE - °C 60 80 100 0.20 0.10 0 0 4 16 8 12 20 IF - QUIESCENT INPUT CURRENT - mA 25 WIDEBODY 0.50 TA = 25°C, RL = 100, VCC = 5 V 0.40 0.30 0.20 0.
PAGE 16
IF PULSE GEN. ZO = 50 tr = 5 ns 0 5V VO 1.5 V 10% DUTY CYCLE 1/f < 100 S 1.5 V VOL IF MONITOR 1 8 2 7 3 6 4 5 +5 V RL 0.1F Figure 10. Switching test circuit. IF 1 8 2 7 3 6 4 5 +5 V B VCM 0 V 10% 90% 90% 10% tr tf VO VO SWITCH AT A: IF = 0 mA 5V A VFF VOL SWITCH AT B: IF = 16 mA + VCM RL 0.1 F VO - PULSE GEN. Figure 11. Test circuit for transient immunity and typical waveforms.