Datasheet

ManualsBrandsBROADCOM ManualsLEDs & AccessoriesSMD LED (multi-colour) PLCC6 RGB 745 mcd, 1600 mcd, 380 mcd 120 ° 20 mA, 20 mA, 20 mA 2.1 V, 3.2 V, 3.2 V ASMT-

ASMT-YTB2-0BB02

High Brightness Tricolor PLCC6 Black Surface LED

Data Sheet

Description

The high brightness black top surface tri-color PLCC-6

family of SMT LEDs has a separate heat path for each LED

dice, enabling the LED to be driven at higher current.

These SMT LEDs are in the high brightness category,

are high reliability devices, are high performance and

are designed for a wide range of environmental condi-

tions. By integrating the black top surface Avago devices

deliver better contrast enhancement for your applica-

tion. They also provide super wide viewing angle at 120°

with the built in reector pushing up the intensity of the

light output. The high reliability characteristics and other

features make the black top surface tri-color PLCC-6 family

ideally suitable for exterior and interior full color signs ap-

plication conditions.

For easy pick & place, the LEDs are shipped in EIA-com-

pliant tape and reel. Every reel is shipped from a single

intensity and color bin; except red color providing better

uniformity. These tri-color LEDs are compatible with

reow soldering process.

Features

x Industry Standard PLCC-6 package (Plastic Leaded Chip

Carrier) with individual addressable pin-out for higher

exibility of driving conguration

x High reliability LED package with silicone encapsulation

x High brightness using AlInGaP and InGaN dice

technologies

x Wide viewing angle at 120°

x Compatible with reow soldering process

x JEDEC MSL 2a

x Water-Resistance (IPX6*) per IEC 60529:2001

* The test is conducted on component level by mounting the

components on PCB with proper potting to protect the leads. It is

strongly recommended that customers perform necessary tests on

the components for their nal application.

Applications

x Indoor and outdoor full color display

CAUTION: LEDs are Class 1C ESD sensitive. Please observe appropriate precautions during han-

dling and processing. Please refer to Avago Application Note AN-1142 for additional details.

Summary of content (11 pages)

PAGE 1
ASMT-YTB2-0BB02 High Brightness Tricolor PLCC6 Black Surface LED Data Sheet Description Features The high brightness black top surface tri-color PLCC-6 family of SMT LEDs has a separate heat path for each LED dice, enabling the LED to be driven at higher current. These SMT LEDs are in the high brightness category, are high reliability devices, are high performance and are designed for a wide range of environmental conditions.
PAGE 2
Package Dimensions Lead Configuration 3 5 2 6 1 1 Cathode Blue 2 Cathode Green 3 Cathode Red 4 Anode Red 5 Anode Green 6 Anode Blue 0.50 4 2.30 2.30 2.80 2.30 3.00 3.40 4 Notes: 1. All Dimensions are in millimeters 2. Tolerance = ±0.2 mm unless otherwise specified 3. Terminal Finish: Ag plating 4. Encapsulantion material: silicone resin 3 1.80 Red 5 2 Green 6 0.20 1 Blue 0.90 Table 1. Device Selection Guide Color 2 - InGaN Green Color 1 - AlInGaP Red Min.
PAGE 3
Table 2. Absolute Maximum Ratings (TA = 25°C) Parameter Red Green & Blue Unit DC forward current [1] 50 30 mA Peak forward current [2] 100 100 mA Power dissipation 125 114 mW Reverse voltage 4V[3] V Maximum junction temperature Tj max 125 °C -40 to + 110[4] °C -40 to + 120 °C Operating temperature range Storage temperature range Notes: 1. Derate linearly as shown in Figure 4a & 4b. 2. Duty Factor = 10% Frequency = 1KHz 3.
PAGE 4
100 0.8 80 BLUE GREEN FORWARD CURRENT-mA RELATIVE INTENSITY 1.0 RED 0.6 0.4 0.2 0.0 400 450 500 550 600 WAVELENGTH - nm 650 RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20mA) 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 Blue / Green 60 40 20 0 700 Figure 1. Relative Intensity vs Wavelength Red 0 1 2 3 FORWARD VOLTAGE-V 4 5 Figure 2. Forward Current-mA vs Forward Voltage-V Red Blue Green 0 20 40 60 80 DC FORWARD CURRENT-mA 100 120 Figure 3.
PAGE 5
1.0 0.8 0.8 NORMALIZED INTENSITY NORMALIZED INTENSITY 1.0 0.6 0.4 0.2 Red 0.0 -90 -60 Green 0.6 0.4 0.2 Blue -30 0 30 ANGULAR DISPLACEMENT-DEGREE Red 60 0.0 -90 90 Figure 5a. Radiation Pattern for X axis -60 Green Blue -30 0 30 60 ANGULAR DISPLACEMENT-DEGREE 90 Figure 5b. Radiation Pattern for Y axis Y X X Y Figure 5c. Component Axis for Radiation Patterns 0.3 1 0.1 -40 Red -20 Green Blue 0 20 40 60 80 100 TJ - JUNCTION TEMPERATURE & Figure 6.
PAGE 6
1.35 4.35 4.35 4.35 1.60 0.40 0.50 Reflow soldering direction 5.25 0.50 0.40 2.35 4.35 1.60 Figure 8a. Recommended soldering land pattern. Figure 8b. LED Configuration on land pattern ID OD ID = 1.7mm OD = 3.5mm Figure 9. Recommended Pick and Place Nozzle Tip 20 SEC. MAX. 183°C 100-150°C -6°C/SEC. MAX. 3°C/SEC. MAX. 120 SEC. MAX. 60-150 SEC. TIME Figure 10. Recommended leaded reflow soldering profile. TEMPERATURE TEMPERATURE 10 to 30 SEC. 240°C MAX. 3°C/SEC. MAX.
PAGE 7
Package Marking 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 1.50 +0.10 –0 1.75 ±0.10 2.29 ±0.1 3.50 ±0.05 8.00 1.00 3.05 ±0.10 +0.30 –0.10 +0.10 –0 3.81 ±0.10 0.229 ±0.01 8° Figure 12. Carrier tape Dimension Ø 20.5 ±0.3 +0.5 2 –0 62.5 +0 –2.5 180 Ø 13 ±0.2 8.4 +1.50 –0.00 (MEASURED AT OUTER EDGE) 14.4 (MAX. MEASURED AT HUB) LABEL AREA (111 mm x 57 mm) WITH DEPRESSION (0.25 mm) Figure 13. Reel Dimension 7 7.9 (MIN.) 10.9 (MAX.
PAGE 8
USER FEED DIRECTION PIN 1 PRINTED LABEL Figure 14.
PAGE 9
Example indicates luminous Intensity information for Red, Green and Blue respectively from label: CAT: V1 W1 T2 Intensity for Blue Intensity for Green Intensity for Red Example indicates color bin information for Green and Blue from label: BIN: A B Color Bin for Blue Color Bin for Green Note: There will be no red color bin information appear on label as it is not binned and support with full distribution range.
PAGE 10
Color Bin Limits Red Color Bin Table Bin ID Min Dom Max Dom Full Distribution 618 628 x 0.6873 0.6696 0.6866 0.7052 y 0.3126 0.3136 0.2967 0.2948 x 0.1142 0.1799 0.2138 0.1625 y 0.8262 0.6783 0.6609 0.8012 0.1387 0.1971 0.2298 0.1854 Tolerance of each bin limit is ± 1 nm Green Color Bin Table Bin ID Min Dom Max Dom A 525.0 531.0 B 528.0 534.0 x y 0.8148 0.6703 0.6507 0.7867 C 531.0 537.0 x 0.1625 0.2138 0.2454 0.2077 y 0.8012 0.6609 0.6397 0.
PAGE 11
Handling Precaution B. Control after opening the MBB The encapsulation material of the LED is made of silicone for better product reliability. Since silicone is a soft material, avoid pressing on the silicon or poking the silicon with a sharp object as the product could be damaged and cause premature failure. During assembly handling, the unit should be held by the body only. Please refer to Avago Application Note AN 5288 for additional handling information and proper procedures.