Datasheet

11
Electrical Specications
Over recommended operating range (4.5V ≤ V
DD1
≤ 5.5V, 4.5V ≤ V
DD2
≤ 5.5V, T
A
= -40°C to +100°C) unless otherwise specied.
All typical specications are at T
A
= +25°C, V
DD1
= V
DD2
= +5.0V.
Parameter Symbol Min. Typ. Max. Units Test Conditions
Input Threshold Current I
TH
2.7 7.0 mA I
OL(Sinking)
=13 mA, V
O
= 0.6V
High Level Output Current I
OH
3.8 100.0 µA I
F
= 250 µA, V
O
= 5.5V
Low Level Output Voltage V
OL
0.36 0.6 V I
OL(Sinking)
=13 mA, I
F
=7 mA
High Level Supply Current (per channel) I
DDH
4.3 7.5 mA I
F
= 0 mA
Low Level Supply Current (per channel) I
DDL
5.8 10.5 mA I
F
= 10 mA
Input Forward Voltage V
F
1.25 1.52 1.8 V I
F
= 10 mA, T
A
= 25°C
Input Reverse Breakdown Voltage BV
R
5.0 V I
R
= 10 µA
Input Diode Temperature Coecient ∆V
F
/ ∆T
A
-1.8 mV/°C I
F
= 10 mA
Input Capacitance C
IN
80 pF f = 1 MHz, V
F
= 0V
Switching Specications
Over recommended operating range (4.5V ≤ V
DD1
≤ 5.5V, 4.5V ≤ V
DD2
≤ 5.5V, I
F
= 8.0 mA, T
A
= -40°C to +100°C) unless otherwise
specied. All typical specications are at T
A
=+25°C, V
DD1
= V
DD2
= +5.0V.
Parameter Symbol Min. Typ. Max. Units Test Conditions
Maximum Data Rate 10 15 MBd R
L
= 350Ω, C
L
=15 pF
Pulse Width t
PW
100 ns R
L
= 350Ω, C
L
=15 pF
Propagation Delay Time to Logic High Output Level
[5]
t
PLH
46 100 ns R
L
= 350Ω, C
L
=15 pF
Propagation Delay Time to Logic Low Output Level
[6]
t
PHL
43 100 ns R
L
= 350Ω, C
L
=15 pF
Pulse Width Distortion |t
PHL
– t
PLH
| |PWD| 5 35 ns R
L
= 350Ω, C
L
=15 pF
Propagation Delay Skew
[7]
t
PSK
40 ns R
L
= 350Ω, C
L
=15 pF
Output Rise Time (10 – 90%) t
R
30 ns R
L
= 350Ω, C
L
=15 pF
Output Fall Time (10 – 90%) t
F
12 ns R
L
= 350Ω, C
L
=15 pF
Logic High Common Mode Transient Immunity
[8]
|CM
H
| 10 kV/µs V
cm
= 1000V, I
F
=0 mA,
V
O
= 2.0V, R
L
=350Ω,
T
A
= 25°C
Logic Low Common Mode Transient Immunity
[8]
|CM
L
| 10 kV/µs V
cm
= 1000V, I
F
= 8 mA,
V
O
= 0.8V, R
L
= 350Ω,
T
A
= 25°C
Notes:
5. t
PLH
is measured from the 4.0 mA level on the falling edge of the input pulse to the 1.5V level on the rising edge of the output pulse.
6. t
PHL
is measured from the 4.0 mA level on the rising edge of the input pulse to the 1.5V level on the falling edge of the output pulse.
7. t
PSK
is equal to the worst case dierence in t
PHL
and/or t
PLH
that will be seen between units at any given temperature and specied test condi-
tions.
8. CM
H
is the maximum common mode voltage slew rate that can be sustained while maintaining V
O
> 2.0V. CM
L
is the maximum common mode
voltage slew rate that can be sustained while maintaining V
O
< 0.8V. The common mode voltage slew rates apply to both rising and falling
common mode voltage edges.