Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysLogicGate Optocoupler SSO 6 Type (misc.) 10 MBd, 35 ns, 1-channel

Description

The ACPL-W611/ACPL-P611 is an optically coupled gate

that combines a GaAsP light emitting diode and an inte-

grated high gain photo detector. The output of the de-

tector IC is an open collector Schottky clamped transis-

tor. The internal shield provides a guaranteed common

mode transient immunity specication of 10,000 V/µs for

the ACPL-W611.

This unique design provides maximum ac and dc circuit

isolation while achieving TTL compatibility. The optocou-

pler ac and dc operational parameters are guaranteed

from -40°C to +85°C allowing trouble-free system perfor-

mance.

The ACPL-W611/ACPL-P611 is suitable for high speed

logic interfacing, input/output buering, as line

receivers in environments that conventional line receiv-

ers cannot tolerate and are recommended for use in ex-

tremely high ground or induced noise environments.

Features

• 10 kV/µs minimum Common Mode Rejection (CMR)

at VCM = 1000 V

• High speed: 10 MBd typical

• LSTTL/TTL compatible

• Low input current capability: 5 mA

• Guaranteed ac and dc performance over temperature:

-40°C to +85°C

• Stretched SO-6 package

• Safety Approval:

– UL Recognized: 3750 V rms for 1 minute and 5000

Vrms* for 1 minute per UL1577

– CSA

– IEC/EN/DIN EN 60747-5-2– pending approval

Applications

• Isolated line receiver

• Computer-peripheral interfaces

• Microprocessor system interfaces

• Digital isolation for A/D, D/A conversion

• Switching power supply

• Instrument input/output isolation

• Ground loop elimination

• Pulse transformer replacement

• Power transistor isolation in motor drives

• Isolation of high speed logic systems

Functional Diagram

A 0.1 µF bypass capacitor must be connected be-

tween pins V

and GND.

ACPL-W611/ACPL-P611

High CMR, High Speed TTL Compatible Optocoupler

Data Sheet

CATHODE

GND

ACPL-W611/ACPL-P611

ANODE

LED

OFF

OUTPUT

TRUTH TABLE

(POSITIVE LOGIC)

SHIELD

CAUTION: It is advised that normal static precautions be taken in handling and assembly

of this component to prevent damage and/or degradation which may be induced by ESD.

Lead (Pb) Free

RoHS 6 fully

compliant

RoHS 6 fully compliant options available;

-xxxE denotes a lead-free product

Summary of content (11 pages)

PAGE 1
ACPL-W611/ACPL-P611 High CMR, High Speed TTL Compatible Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features The ACPL-W611/ACPL-P611 is an optically coupled gate that combines a GaAsP light emitting diode and an integrated high gain photo detector. The output of the detector IC is an open collector Schottky clamped transistor.
PAGE 2
Schematic Diagram ACPL-W60L IF ICC 6 1+ IO 5 VCC VO VF – 3 4 SHIELD GND Ordering Information ACPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577 and is approved under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 3
Package Outline Drawings ACPL-W611 Stretched SO-6 Package LAND PATTERN RECOMMENDATION 12.650 (0.498) 1.270 (0.050) 0.381 (0.015) 1 6 2 5 3 4 0.760 (0.030) 4.580 (0.180) 1.905 (0.075) 7° 0.450 (0.018) 7° 45° 1.590 (0.063) 3.180 (0.125) 0.200 ± 0.100 (0.008 ± 0.004) 6.807 (0.268) 0.750 (0.0295) DIMENSIONS IN MILLIMETERS AND (INCHES). 11.500 ± 0.300 (0.453 ± 0.012) COPLANARITY = 0.10 mm (0.004 INCHES). ACPL-P611 Stretched SO-6 Package LAND PATTERN RECOMMENDATION 10.7 (0.421) 1.27 (0.
PAGE 4
Recommended Solder Reflow Thermal Profile 300 TEMPERATURE (°C) PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. 200 PEAK TEMP. 245°C PEAK TEMP. 240°C 2.5°C ± 0.5°C/SEC. 30 SEC. 160°C 150°C 140°C PEAK TEMP. 230°C SOLDERING TIME 200°C 30 SEC. 3°C + 1°C/–0.5°C 100 PREHEATING TIME 150°C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 150 200 250 TIME (SECONDS) Note: Use of non chlorine-activated fluxes is highly recommended.
PAGE 5
Insulation and Safety Related Specifications Parameter Symbol ACPL-P611 ACPL-W611 Units Conditions Minimum External Air Gap L(101) 7 8 mm Clearance) Measured from input (External terminals to output terminals, shortest distance through air. Minimum External Tracking L(102) 8 8 mm (External Creepage) Measured from input terminals to output terminals, shortest distance path along body. Minimum Internal Plastic Gap 0.08 0.
PAGE 6
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics* (ACPL-W611/ ACPL-P611 Option 060) ACPL-P611 Option 060 ACPL-W611 Option 060 for rated mains voltage ≤ 150 Vrms I – IV I – IV for rated mains voltage ≤ 300 Vrms I – IV I – IV for rated mains voltage ≤ 450 Vrms I – III I – III for rated mains voltage ≤ 600 Vrms I – III I – III Description Symbol Unit Installation classification per DIN VDE 0110/1.
PAGE 7
Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -55 125 °C Operating Temperature TA -40 85 °C Average Input Current IF(AVG) 20 mA Reverse Input Voltage VR 5 V Input Power Dissipation PI 45 mW Supply Voltage (1 Minute Maximum) VCC 7 V Output Collector Current IO 50 mA Output Collector Voltage VO 7 V Output Collector Power Dissipation PO 85 mW Lead Solder Temperature TLS 260°C for 10 sec.
PAGE 8
Switching Specifications (AC) Over recommended operating conditions TA = -40°C to 85°C, VCC = 5 V, IF = 7.5 mA unless otherwise specified. All typicals at VCC = 5 V, TA = 25 °C. Parameter Symbol Min. Typ. Max. Units Test Conditions Propagation Delay Time to tPLH 20 48 High Output Level 75 ns TA = 25°C 100 25 50 Propagation Delay Time to tPHL Low Output Level 75 100 ns Pulse Width Distortion |tPHL - tPLH| 3.5 35 ns 40 Fig.
PAGE 9
0.5 VCC = 5.5 V VO = 5.5 V IF = 250 µA VOL – LOW LEVEL OUTPUT VOLTAGE – V IOH – HIGH LEVEL OUTPUT CURRENT – µA 15 10 5 0 -60 -40 -20 0 20 40 60 VCC = 5.5 V IF = 5.0 mA 0.4 IO = 12.8 mA IO = 16 mA 0.3 IO = 6.4 mA 0.2 IO = 9.6 mA 0.1 -60 -40 -20 80 100 TA – TEMPERATURE – °C Figure 1. High level output current vs. temperature 0.1 0.01 1.20 1.30 1.40 80 60 100 VCC = 5 V TA = 25 °C 5 VO – OUTPUT VOLTAGE – V IF – FORWARD CURRENT – mA IF + VF – 0.001 1.10 40 6 TA = 25°C 1.
PAGE 10
5 VCC = 5.0 V IF = 7.5 mA tPLH , RL = 4 KΩ 80 tP – PROPAGATION DELAY – ns tP – PROPAGATION DELAY – ns 100 tPHL , RL = 350 Ω 1 KΩ 4 KΩ 60 tPLH , RL = 1 KΩ 40 tPLH , RL = 350 Ω 20 0 -60 -40 -20 0 20 40 80 60 tPLH , RL = 4 KΩ 90 75 tPLH , RL = 350 Ω 60 tPLH , RL = 1 KΩ 45 30 100 VCC = 5.0 V TA = 25°C tPHL , RL = 350 Ω 1 KΩ 4 KΩ 5 7 TA – TEMPERATURE – °C Figure 7. Propagation delay vs. temperature tr, tf – RISE, FALL TIME – ns PWD – PULSE WIDTH DISTORTION – ns 30 VCC = 5.
PAGE 11
ITH – INPUT THRESHOLD CURRENT – mA 6 5 VCC = 5.0 V VO = 0.6 V 4 3 RL = 350 Ω RL = 1 kΩ 2 1 RL = 4 kΩ 0 -60 -40 -20 0 20 40 60 80 100 TA – TEMPERATURE – °C Figure 13. Input threshold current vs. temperature For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change.