Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysLogicGate Optocoupler SSO 6 Type (misc.) 15 MBd, 25 ns, 1-channel, 3.3 V

CATHODE

GND

ANODE

CATHODE

ANODE

GND

ACPL-W60L

ACPL-K63L

ANODE

LED

OFF

ENABLE

OUTPUT

TRUTH TABLE

(POSITIVE LOGIC)

LED

OFF

OUTPUT

TRUTH TABLE

(POSITIVE LOGIC)

SHIELD

Description

The ACPL-W60L/K63L are optically coupled gates that

combine a GaAsP light emitting diode and an integrated

high gain photo detector. The output of the detector IC is

an open collector Schottky-clamped transistor. The internal

shield provides a guaranteed common mode transient

immunity specication of 15 kV/µs at 3.3V.

This unique design provides maximum AC and DC circuit

isolation while achieving LVTTL/LVCMOS compatibility.

The optocoupler AC and DC operational parameters are

guaranteed from –40˚C to +85˚C allowing trouble-free

system performance.

Functional Diagram

Features

• Dual Voltage Operation (3.3V/5V)

• Package clearance/creepage at 8 mm

• Low power consumption

• 15 kV/µs minimum Common Mode Rejection (CMR)

at V

= 1000V

• High speed: 15 MBd typical

• LVTTL/LVCMOS compatible

• Low input current capability: 5 mA

• Guaranteed AC and DC performance over tempera-

ture: –40˚C to +85˚C

• Available in 6-pin stretched SO-6 and 8 pin stretched

SO-8

• Safety approvals: UL, CSA, IEC/EN/DIN EN 60747-5-2

– in process

Applications

• Isolated line receiver

• Computer-peripheral interfaces

• Microprocessor system interfaces

• Digital isolation for A/D, D/A conversion

• Switching power supply

• Instrument input/output isolation

• Ground loop elimination

• Pulse transformer replacement

• Fieldbus

A 0.1 µF bypass capacitor must be connected between pins 5 and 8.

ACPL-W60L/K63L

High Speed LVTTL Compatible 3.3 Volt/5 Volt Optocouplers

Data Sheet

Lead (Pb) Free

RoHS 6 fully

compliant

RoHS 6 fully compliant options available;

-xxxE denotes a lead-free product

CAUTION: It is advised that normal static precautions be taken in handling and assembly

of this component to prevent damage and/or degradation which may be induced by ESD.

Summary of content (13 pages)

PAGE 1
ACPL-W60L/K63L High Speed LVTTL Compatible 3.3 Volt/5 Volt Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features The ACPL-W60L/K63L are optically coupled gates that combine a GaAsP light emitting diode and an integrated high gain photo detector. The output of the detector IC is an open collector Schottky-clamped transistor.
PAGE 2
Schematic Diagrams IF ACPL-W60L ACPL-K63L ICC 6 1+ IO 5 VCC 1 VO ICC 8 IF1 IO1 + 7 VCC VO1 VF1 VF – – 3 4 SHIELD 2 GND SHIELD 3 IO2 – USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED 6 VO2 VF2 BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5).
PAGE 3
Package Outline Drawings ACPL-W60L Stretched SO-6 Package LAND PATTERN RECOMMENDATION 12.65 (0.498) 1.27 (0.050) BSG 0.381 ± 0.127 (0.015 ± 0.005) 1 6 2 5 3 4 +0.127 6.807 0 +0.005 0.268 -0.000 ( 0.45 (0.018) 7° +0.254 4.580 0 +0.010 0.180 -0.000 ( 0.76 (0.030) ) 1.91 (0.075) ) 1.590 ± 0.127 (0.063 ± 0.005) 7° 45° 3.180 ± 0.127 (0.125 ± 0.005) 0.20 ± 0.10 (0.008 ± 0.004) 0.750 ± 0.250 (0.0295 ± 0.010) DIMENSIONS IN MILLIMETERS (INCHES). 11.50 ± 0.250 (0.453 ± 0.
PAGE 4
Recommended Solder Reflow Thermal Profile 300 TEMPERATURE (°C) PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. 200 PEAK TEMP. 245°C PEAK TEMP. 240°C 2.5°C ± 0.5°C/SEC. SOLDERING TIME 200°C 30 SEC. 160°C 150°C 140°C PEAK TEMP. 230°C 30 SEC. 3°C + 1°C/–0.5°C 100 PREHEATING TIME 150°C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 150 200 TIME (SECONDS) Note: Non-halide flux should be used.
PAGE 5
Insulation and Safety Related Specifications Parameter Symbol Stretched SO-6 and SO-8 Value Units Minimum External Air L (101) 8 mm Gap (External Clearance) Minimum External Tracking L (102) 8 mm (External Creepage) Minimum Internal Plastic 0.08 mm Gap (Internal Clearance) Tracking Resistance CTI 175 Volts (Comparative Tracking Index) Isolation Group IIIa Conditions Measured from input terminals to output terminals, shortest distance through air.
PAGE 6
Absolute Maximum Ratings (No Derating Required up to 85˚C) Parameter Symbol Min. Max.
PAGE 7
Electrical Specifications Over Recommended Operating Conditions (TA = –40°C to +85°C , 2.7V ≤ Vcc ≤ 3.6V) unless otherwise specified. All Typicals at VCC = 3.3 V, TA = 25˚C. Parameter Sym. Device Min. Typ. Max. Units Test Conditions Fig. Note High Level IOH* 4.5 50 µA VCC = 3.3 V, VO = 3.3 V, 1 1 Output Current IF = 250 µA Input Threshold ITH 3.0 5.0 mA VCC = 3.3 V, VO = 0.6 V, 2 Current IOL (Sinking) = 13 mA Low Level VOL* 0.35 0.6 V VCC = 3.
PAGE 8
Switching Specifications Over Recommended Temperature (TA = –40˚C to +85˚C), VCC = 3.3 V, IF = 7.5 mA unless otherwise specified. All Typicals at TA = 25˚C, VCC = 3.3 V. Parameter Sym. Min. Typ. Max. Units Propagation Delay tPLH 90 ns Time to High Output Level Test Conditions Fig.
PAGE 9
Parameter Sym. Device Min. Typ. Units Test Conditions Fig. Note Output High Level Common Mode Transient Immunity |CMH| ACPL-W60L ACPL-K63L 15 25 kV/ms VCC = 3.3 V, IF = 0 mA, VO(MIN) = 2 V, RL = 350 W, TA = 25°C, VCM = 1000 V and VCM = 10 V 9 10, 12 Output Low Level Common Mode Transient Immunity |CML| ACPL-W60L ACPL-K63L 15 25 kV/ms VCC = 3.3 V, IF = 7.5 mA, VO(MAX) = 0.
PAGE 10
Package Characteristics All Typicals at TA = 25˚C. Parameter Sym. Package Min. Typ. Max Units Test Conditions Fig. Note Input-Output II-O* Single 1 µA 45% RH, t = 5 s, 13, 14 Insulation VI-O = 3 kV DC, TA = 25˚C Input-Output VISO Single, 3750 V rms RH ≤ 50%, t = 1 min, 13, 14 Momentary Dual Channel TA = 25˚C Withstand Voltage* Input-Output RI-O Single, 1012 Ω VI-O =500 V dc 1, 13, 15 Resistance Dual Channel Input-Output CI-O Single, 0.
PAGE 11
15 VCC = 3.3 V VO = 3.3 V IF = 250 µA 10 5 0 -60 -40 -20 0 20 40 60 80 100 I OH - HIGH LEVEL OUTPUT CURRENT - µA IOH – HIGH LEVEL OUTPUT CURRENT – µA 15 V CC = 5.5 V V O = 5.5 V I F = 250 µA 10 5 0 -60 -40 0 -20 20 40 80 100 60 T A - TEMPERATURE - °C TA – TEMPERATURE – C 12 10 VCC = 3.3 V VO = 0.6 V 8 RL = 350 KΩ 6 RL = 1 KΩ 4 2 RL = 4 KΩ 0 -60 -40 -20 0 20 40 60 80 100 ITH – INPUT THRESHOLD CURRENT – mA ITH – INPUT THRESHOLD CURRENT – mA Figure 1.
PAGE 12
60 50 IF = 5.0 mA 40 20 -60 -40 -20 0 20 40 80 80 60 1000 V CC = 5.0 V V OL = 0.6 V TA = 25 °C IF – FORWARD CURRENT – mA VCC = 3.3 V VOL = 0.6 V I OL - LOW LEVEL OUTPUT CURRENT - mA IOL – LOW LEVEL OUTPUT CURRENT – mA 70 60 40 I F = 5.0 mA 20 0 -60 -40 100 -20 0 20 40 60 PULSE GEN. ZO = 50 Ω tf = tr = 5 ns VCC 6 0.1 µF BYPASS INPUT MONITORING NODE RL 5 2 *CL 3 GND 2 7 3 6 4 5 IF = 7.50 mA IF = 3.75 mA tPLH 1.
PAGE 13
40 VCC = 3.3 V IF = 7.5 mA 40 PWD - PULSE WIDTH DISTORTION - ns PWD – PULSE WIDTH DISTORTION – ns 50 30 RL = 350 Ω 20 10 0 -60 -40 -20 0 20 40 60 80 30 20 R L = 350 kΩ 10 0 -10 100 V CC = 5.0 V I F = 7.5 mA -60 -40 TA – TEMPERATURE – C -20 0 20 40 80 60 100 T A - TEMPERATURE - °C Figure 8. Typical pulse width distortion vs. temperature. IF IF SINGLE CHANNEL B A VFF 1 VCC 6 5 2 3 GND DUAL CHANNEL B 0.1 µF BYPASS VCC 8 1 A +3.