User manual

5-6 Section 5: Module Configuration
Moseley SL9003Q 602-12016 Revision G
ISO/MPEG Decoder Board
M1 M2 M3 M4 ISO/MPEG Rate
off=0 off=0 off=0 off=0 reserved
off=0 off=0 off=0 on=1 32 kb/s
off=0 off=0 on=1 off=0 48 kb/s
off=0 off=0 on=1 on=1 56 kb/s
off=0 on=1 off=0 off=0 64 kb/s
off=0 on=1 off=0 on=1 80 kb/s
off=0 on=1 on=1 off=0 96 kb/s
off=0 on=1 on=1 on=1 112 kb/s
on=1 off=0 off=0 off=0 128 kb/s
on=1 off=0 off=0 on=1 160 kb/s
on=1 off=0 on=1 off=0 192 kb/s
on=1 off=0 on=1 on=1 224 kb/s
on=1 on=1 off=0 off=0 256 kb/s
on=1 on=1 off=0 on=1 320 kb/s
on=1 on=1 on=1 off=0 384 kb/s
on=1 on=1 on=1 on=1 forbidden
S21 – Data Channel
D1 D2 Aux Data # of Bits
off=0 off=0 6 (6N/5E/50)
off=0 on=1 7 (7N/6E/60)
on=1 off=0 8 (8N/7E/70) [default]
on=1 on=1 9 (9N/8E/80)
D3 D4 D5 Aux Date Rate
off=0 off=0 off=0 300
off=0 off=0 on=1 600
off=0 on=1 off=0 1200 [default]
off=0 on=1 on=1 2400
on=1 off=0 off=0 4800
on=1 off=0 on=1 9600 +
on=1 on=1 off=0 19200 +
on=1 on=1 on=1 38400 +
+ MUST use CTS Line
D6 Reserved
off=0 Reserved [default]
on-1 Reserved
D7 Test
off=0 Disabled [default]
on=1 Enabled
D8 Debug
off=0 Normal [default]
on=1 Enabled
S22 – Board ID
A2 A3 A4 A5 A6 A7 A8 A9 Board # Base Addr
off off off off off off off off 0 0
off on off off off off off off 2 8
off off on off off off off off 3 16
off off off on off off off off 4 32
off off off off off on off off 6 128
off off off off off off on off 7 256
S23 – System Config
R1 R2 Sample Rate Cnvtr Data Source
off=0 off=0 Compressed
off=0 on=1 Linear
on=1 off=0 Zeros (gnd)
on=1 on=1 Sine
R3 Trunk Compressed Input Clock
off=0 Normal [default]
on=1 Inverted
R4 Trunk Linear Input Clock
off=0 Normal [default]
on=1 Inverted
R5 R6 2-/4-Channel Select
off=0 off=0 2-Channel
off=0 on=1 reserved
on=1 off=0 4-Channel Master (1
st
pair)
on=1 on=1 4-Channel Slave (2
nd
pair)
R7 9003 LEDs & Metering
off=0 Disabled/FP Select [default]
on=1 Enabled/Forced On
R8 Debug (B-Bus)
off=0 disabled [default]
on=1 enabled
S32 – System Config
M1 M2 Input Rate (A/D & AES/EBU/SPDIF &SRC
off=0 off=0 44.1 kHz (internal osc)
off=0 on=1 48.0 kHz (internal osc)
on=1 off=0 32.0 kHz (internal osc) [default]
on=1 on=1 Linear Rate (M7, M8)
M3 VCO Test
off=0 Normal (external)
on=1 Test (internal)
M4 FIFO data source
off=0 trunk
on=1 mux
M5 M6 VCO Source
off=0 off=0 trunk compresssed
off=0 on=1 trunk linear
on=1 off=0 mux compressed
on=1 on=1 mux linear
M7 M8 VCO Rate Clk Freq
off=0 off=0 44.1 kHz 11.286 MHz
off=0 on=1 48.0 kHz 12.2880 MHz
on=1 off=0 32.0 kHz 8.1920 MHz
on=1 on=1 44.0 kHz 11.2460 MHz
S52 – System Clock
RXD RXC Modem RX Compressed
off X RXDATA disabled [default]
on X RXDATA enabled
X off RXCLK disabled [default]
X on RXCLK enabled
S52-3
S52-4 Modem RX Linear
off X RXDATA disabled [default]
on X RXDATA enabled
X off RXCLK disabled [default]
X on RXCLK enabled
S81- AES/EBU
S81-A S81-B S81-c S81-D S81-E AES/EBU/SPDIF
off off off off on AES/EBU [default]
on on off off off SPDIF
Audio Out Card
E3-E4-E7-E8 Analog Output Impedence
LO <5 ohms
600 600 ohms [default]
Figure 5-4 Audio Decoder PC Board / Switch & Jumper Settings